This application note shows how to write an Inter Integrated Circuit bus driver (I²C) for the Philips P90CL301micro-controller.It is not only an example of writing a driver, but it also includes a set of application interface software routines toquickly implement a complete I²C multi-master system application.For specific applications the user will have to make minimal changes in the driver program. Using the drivermeans linking modules to your application software and including a header-file into the application sourceprograms. A small example program of how to use the driver is listed.The driver supports i.a. polled or interrupt driven message handling, slave message transfers and multi-mastersystem applications. Furthermore, it is made suitable for use in conjunction with real time operating systems, likepSOS+.
上传时间： 2013-11-23
上传用户：weixiao99
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
上传时间： 2014-01-24
上传用户：zl5712176
基于单片机的汽车多功能报警系统设计The Design of Automobile Multi-function AlarmingBased on Single Chip Computer刘法治赵明富宁睡达(河 南 科 技 学 院 ，新 乡 453 00 3)摘要介绍了一种基于单片机控制的汽车多功能报警系统，它能对汽车的润滑系统油压、制动系统气压、冷却系统温度、轮胎欠压及防盗进行自动检测，并在发现异常情况时，发出声光报警。阐述了该报警系统的硬件组成及软件设计方法。关键词单片机传感器数模转换报警Abstract Am ulti-fimctiona utomobilea larnungs ystemb asedo ns inglec hipc omputerco ntorlis in torducedin th isp aper.Th eo ilpr essuero flu bricatesystem, air pressure of braking system, temperature of cooling system, under pressure of tyre and guard against theft， detected automaticaly场thesystem. Audio and visual alarms wil be provided under abnormal conditions厂The hardware composition and software design of the system， described.Keywords Singlec hipc omputer Sensor Digital-t-oanaloguec onversion Alarmin 汽车多功能报苦器硬件系统设计根据 系 统 实际需要和产品性价比，选用ATMEL公司新生产的采用CMOs工艺的低功耗、高性能8位单片机AT89S52作为系统的控制器。AT89S52的片内有8k Bytes LSP Flash闪烁存储器，可进行100(〕次写、擦除操作;256Bytes内部数据存储器(RAM);3 2 根可编程输N输出线;2个可编程全双工串行通道;看门狗(WTD)电路等。系统由传感器、单片机、模数转换器、无线信号发射电路、指示灯驱动电路、声光报警驱动电KD一9563，发出三声二闪光。并触发一个高电平，驱动无线信号发射电路。
上传时间： 2013-11-09
上传用户：gxmm
Emu51Form是一个软仿真计时器，copy到keil\c51\bin下 project->option for target "target 1"->debug->dialog.dll->parameter改为-p51R -dEmu51Form即可在keil 7.0运行成功，因为使用的一些函数是在最新的AGSI文档中获得，所以大家试试在6.23下能不能用。
上传时间： 2013-10-28
上传用户：15736969615
设计一种应用于某全地形ATV车载武器装置中的中控系统，该系统设计是以TMS320F2812型DSP为核心，采用模块化设计思想，对其硬件部分进行系统设计，能够完成对武器装置高低、回转方向的运动控制，实现静止或行进状态中对目标物的测距，自动瞄准以及按既定发射模式发射弹丸和各项安全性能检测等功能。通过编制相应的软件，对其进行系统调试，验证了该设计运行稳定。 Abstract: A central control system applied to an ATV vehicle weapons is designed. The system design is based on TMS320F2812 DSP as the core， uses modular design for its hardware parts. The central control system can complete the motion control of the level of weapons and equipment， rotation direction， to achieve a state of static or moving objects on the target ranging， auto-targeting and according to the established target and the projectile and the launch of the security performance testing and other functions. Through the development of appropriate software and to carry out system testing to verify the stability of this design and operation.
上传时间： 2013-11-02
上传用户：jshailingzzh
中文版详情浏览：http://www.elecfans.com/emb/fpga/20130715324029.html Xilinx UltraScale:The Next-Generation Architecture for Your Next-Generation Architecture The Xilinx® UltraScale™ architecture delivers unprecedented levels of integration and capability with ASIC-class system- level performance for the most demanding applications. The UltraScale architecture is the industr y's f irst application of leading-edge ASIC architectural enhancements in an All Programmable architecture that scales from 20 nm planar through 16 nm FinFET technologies and beyond, in addition to scaling from monolithic through 3D ICs. Through analytical co-optimization with the X ilinx V ivado® Design Suite, the UltraScale architecture provides massive routing capacity while intelligently resolving typical bottlenecks in ways never before possible. This design synergy achieves greater than 90% utilization with no performance degradation. Some of the UltraScale architecture breakthroughs include: • Strategic placement (virtually anywhere on the die) of ASIC-like system clocks, reducing clock skew by up to 50% • Latency-producing pipelining is virtually unnecessary in systems with massively parallel bus architecture, increasing system speed and capability • Potential timing-closure problems and interconnect bottlenecks are eliminated, even in systems requiring 90% or more resource utilization • 3D IC integration makes it possible to build larger devices one process generation ahead of the current industr y standard • Greatly increased system performance, including multi-gigabit serial transceivers, I/O, and memor y bandwidth is available within even smaller system power budgets • Greatly enhanced DSP and packet handling The Xilinx UltraScale architecture opens up whole new dimensions for designers of ultra-high-capacity solutions.
标签： UltraScale Xilinx 架构
上传时间： 2013-11-13
上传用户：瓦力瓦力hong
UG157 - LogiCORE™ IP Initiator/Target v3.1 for PCI™ 入门指南
上传时间： 2013-11-06
上传用户：ewtrwrtwe
为提升虚拟仪器传输速率与实时性能，扩展监测范围，在VC的软件平台上设计了一种全功能虚拟示波器。与传统虚拟示波器相比，该系统采用嵌入式系统完成信号采集，采用工业以太网为传输介质，通过线性插值算法和多线程编程思想，实现波形显示、参数计算、频谱分析以及波形存储及回放功能。实验结果表明，该虚拟示波器可以实现20 kHz采样频率下的波形精确显示，达到预期的各项指标。 Abstract: o enhance the transfer rate and real-time of virtual instrument performance， expand scope of monitoring， this paper uses the VCs software platform to design a fully functional virtual oscilloscope. Compared with traditional virtual oscilloscope， this system adopts the embedded system to complete the data acquisition， industrial Ethernet as the transmission medium used by the linear interpolation algorithm and multi-threaded programming ideas， namely to achieve waveform display， parameter calculation， spectrum analysis and waveform storage and playback. Experimental results show that the virtual oscilloscope can accurately display the waveform with 20kHz sampling frequency， and achieve the desired targets.
上传时间： 2013-11-25
上传用户：wbwyl
用MDK 生成bin 文件1用MDK 生成bin 文件Embest 徐良平在RV MDK 中，默认情况下生成*.hex 的可执行文件，但是当我们要生成*.bin 的可执行文件时怎么办呢？答案是可以使用RVCT 的fromelf.exe 工具进行转换。也就是说首先将源文件编译链接成*.axf 的文件，然后使用fromelf.exe 工具将*.axf 格式的文件转换成*.bin格式的文件。下面将具体说明这个操作步骤：1. 打开Axf_To_Bin 文件中的Axf_To_Bin.uv2 工程文件；2. 打开Options for Target ‘Axf_To_Bin’对话框，选择User 标签页；3. 构选Run User Programs After Build/Rebuild 框中的Run #1 多选框，在后边的文本框中输入C:\Keil\ARM\BIN31\fromelf.exe --bin -o ./output/Axf_To_Bin.bin ./output/Axf_To_Bin.axf 命令行；4. 重新编译文件，在./output/文件夹下生成了Axf_To_Bin.bin 文件。在上面的步骤中，有几点值得注意的是：1. C:\Keil\ARM\BIN31\表示RV MDK 的安装目录；2. fromelf.exe 命令的具体语法格式如下：命令的格式为：fromelf [options] input_file命令选项如下：--help 显示帮助信息--vsn 显示版本信息--output file 输出文件(默认的输出为文本格式)--nodebug 在生成的映象中不包含调试信息--nolinkview 在生成的映象中不包含段的信息二进制输出格式：--bin 生成Plain Binary 格式的文件--m32 生成Motorola 32 位十六进制格式的文件--i32 生成Intel 32 位十六进制格式的文件--vhx 面向字节的位十六进制格式的文件t--base addr 设置m32，i32 格式文件的基地址--text 显示文本信息文本信息的标志-v 打印详细信息-a 打印数据地址(针对带调试信息的映象)-d 打印数据段的内容-e 打印表达式表print exception tables-f 打印消除虚函数的信息-g 打印调试表print debug tables-r 打印重定位信息-s 打印字符表-t 打印字符串表-y 打印动态段的内容-z 打印代码和数据大小的信息
上传时间： 2013-12-17
上传用户：AbuGe
同步技术是跳频通信系统的关键技术之一，尤其是在快速跳频通信系统中，常规跳频通信通过同步字头携带相关码的方法来实现同步，但对于快跳频来说，由于是一跳或者多跳传输一个调制符号，难以携带相关码。对此引入双跳频图案方法，提出了一种适用于快速跳频通信系统的同步方案。采用短码携带同步信息，克服了快速跳频难以携带相关码的困难。分析了同步性能，仿真结果表明该方案同步时间短、虚警概率低、捕获概率高，同步性能可靠。 Abstract: Synchronization is one of the key techniques to frequency-hopping communication system， especially in the fast frequency hopping communication system. In conventional frequency hopping communication systems， synchronization can be achieved by synchronization-head which can be used to carry the synchronization information， but for the fast frequency hopping， Because modulation symbol is transmitted by per hop or multi-hop， it is difficult to carry the correlation code. For the limitation of fast frequency hopping in carrying correlation code， a fast frequency-hopping synchronization scheme with two hopping patterns is proposed. The synchronization information is carried by short code， which overcomes the difficulty of correlation code transmission in fast frequency-hopping. The performance of the scheme is analyzed， and simulation results show that the scheme has the advantages of shorter synchronization time， lower probability of false alarm， higher probability of capture and more reliable of synchronization.
上传时间： 2013-11-23
上传用户：mpquest
