I2C(Inter Integrated Circuits)是PhiLips公司开发的用于芯片之间连接的串行总线，以其严格的规范、卓越的性能、简便的操作和众多带I2C接口的外围器件而得到广泛的应用并受到普遍的欢迎。 现场可编程门阵列(FPGA)设计灵活、速度快，在数字专用集成电路的设计中得到了广泛的应用。本论文主要讨论了如何利用Verilog/FPGA来实现一个随机读/写的I2C接口电路，实现与外围I2C接口器件E2PROM进行数据通信，实现读、写等功能，传输速率实现为100KBps。在Modelsim6.0仿真软件环境中进行仿真，在XiLinx公司的ISE9.Li开发平台上进行了下载，搭建外围电路，用Agilem逻辑分析仪进行数据采集，分析测试结果。 首先，介绍了微电子设计的发展概况以及设计流程，重点介绍了HDL/FPGA的设计流程。其次，对I2C串行总线进行了介绍，重点说明了总线上的数据传输格式并对所使用的AT24C02 E2PROM存储器的读／写时序作了介绍。第三，基于Verilog _HDL设计了随机读/写的I2C接口电路、测试模块和显示电路；接口电路由同步有限状态机(FSM)来实现；测试模块首先将数据写入到AT24C02的指定地址，接着将写入的数据读出，并将两个数据显示在外围LED数码管和发光二极管上，从而直观地比较写入和输出的数据的正确性。FPGA下载芯片为XiLinx SPARTAN Ⅲ XC3S200。第四，用Agilent逻辑分析仪进行传输数据的采集，分析数据传输的时序，从而验证电路设计的正确性。最后，论文对所取得的研究成果进行了总结，并展望了下一步的工作。
上传时间： 2013-06-08
上传用户：再见大盘鸡
Li> <Li>移动电源方案功能要求: 1、单芯片控制充电、升压输出、电量指示功能，输出电流可达1A，效率90%以上 按开关键开机6灯频闪几次后待机， Li为充电指示，L2频闪指示有输出。L2I常亮为输出充满指示，L3-L6为电量指示。在输出时L2频闪。充电时Li频闪。当有负载设备连接时自动输出，无负载电流转为待机。 当按开关工作后，无负载（无操作）10秒自动关机。 2、移动电源方案，单芯片控制为内电池充电、升压输出、电量显示、边充边放；输入电压5V、300-1000MA，输出电压5V、；输出电流可达1A，输出效率90%以上 1）、电性能参数： USB输入电压：DC 5V 输出DC5V
上传时间： 2013-11-19
上传用户：wangfei22
Li> <Li>The CN3052A is a complete constant-current /constant voltage Linear charger for single cell Li-ion and Li Polymer rechargeable batteries. The device contains an on-chip power MOSFET and eLiminates the need for the external sense resistor and blocking diode.
上传时间： 2013-11-10
上传用户：子虚乌有
Li> <Li>Linear Technology offers a variety of devices that simpLifyconverting power from a USB cable, but the LTC®3455represents the highest level of functional integration yet. The LTC3455 seamlessly manages power flowbetween an AC adapter, USB cable and Li-ion battery,while complying with USB power standards, all from a4mm × 4mm QFN package. In addtion, two high efficiencysynchronous buck converters generate low voltage railswhich most USB-powered peripherals require. TheLTC3455 also provides power-on reset signals for themicroprocessor, a Hot SwapTM output for poweringmemory cards as well as an uncommitted gain blocksuitable for use as a low-battery comparator or an LDOcontroller. The PCB real estate required for the entire USBpower control circuit and two DC/DC converters is only225mm2.
上传时间： 2013-11-02
上传用户：名爵少年
Li> <Li>Although recent popular attention is focused on LithiumIon batteries, one must not forget that other batterychemistries, such as Nickel Cadmium (NiCd) and NickelMetal Hydride (NiMH) have advantages in rechargeablepower systems. Nickel-based batteries are robust, capableof high discharge rates, have good cycle Life, do notrequire special protection circuitry and are less expensivethan Li-Ion. Among the two, NiMH batteries are rapidlyreplacing NiCd because of their higher capacity (40% to50% more) and the environmental concerns of the toxiccadmium contained in NiCd batteries.
上传时间： 2013-11-04
上传用户：qq10538412
Li> <Li>A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered appLications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, complex magnetics,polarity inversion and/or circuit complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
上传时间： 2013-10-21
上传用户：ljt101007
Li> <Li>The LTC®3562 quad output step-down regulator is designedfor multicore handheld microprocessor appLications thatoperate from a single Li-Ion battery. Its four monoLithic, higheffi ciency buck regulators support Intel’s mobile CPU P-Stateand C-State energy saving operating modes. The outputvoltages are independently controllable via I2C, and eachoutput can be independently started and shut down. Designerscan choose from power saving pulse-skipping mode orBurst Mode® operation, or select low noise LDO mode. Thespace-saving LTC3562 is available in a 3mm × 3mm QFNpackage and requires few external components.
上传时间： 2013-10-07
上传用户：1583060504
Li> <Li>Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabiLization. Theyare relatively small, Lightweight and effi cient, but theyalso require a compLicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上传时间： 2013-11-18
上传用户：hulee
Li> <Li>Automotive power systems are unforgiving electronicenvironments. Transients to 90V can occur when thenominal voltage range is 10V to 15V (ISO7637), along withbattery reversal in some cases. It’s fairly straightforwardto build automotive electronics around this system, butincreasingly end users want to operate portable electronics,such as GPS systems or music/video players,and to charge their Li-Ion batteries from the automotivebattery. To do so requires a compact, robust, effi cientand easy-to-design charging system
上传时间： 2013-11-04
上传用户：wfl_yy
Li> <Li>The LTC®4155 and LTC4156 are dual multiplexed-inputbattery chargers with PowerPath™ control, featuring I2CprogrammabiLity and USB On-The-Go for systems suchas tablet PCs and other high power density appLications.The LTC4155’s float voltage (VFLOAT) range is optimizedfor Li-Ion batteries, while the LTC4156 is optimized forLithium iron phosphate (LiFePO4)batteries, supportingsystem loads to 4A with up to 3.5A of battery chargecurrent. I2C controls a broad range of functions and USBOn-The-Go functionaLity is controlled directly from theUSB connector ID pin.
上传时间： 2013-10-09
上传用户：hanhanj
Li>