ARM S3C2410硬件手册重点 a.Memory Controller b.Nand Flash c.UART d.Interrupt e.Timer
标签: Controller Interrupt S3C2410 Memory
上传时间: 2013-12-16
上传用户:懒龙1988
MSP430F1610 generates a sine wave from a look up table using timer interrupt.
标签: generates interrupt F1610 table
上传时间: 2016-10-31
上传用户:hustfanenze
Echo a received character, RX ISR used. Normal mode is LPM0. // USART1 RX interrupt triggers TX Echo. // Baud rate divider with 1048576hz = 1048576/38400 = ~27.31 (01Bh|03h) // ACLK = LFXT1 = 32768Hz, MCLK = SMCLK = default DCO = 32 x ACLK = 1048576Hz // //* An external watch crystal between XIN & XOUT is required for ACLK
标签: character interrupt received triggers
上传时间: 2016-10-31
上传用户:rishian
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上传时间: 2013-12-12
上传用户:himbly
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上传时间: 2014-01-19
上传用户:三人用菜
ST32 基于(英蓓特)STM32V100的EXTI程序 This example shows how to configure an external interrupt line. In this example, the EXTI line 9 is configured to generate an interrupt on each falling edge. In the interrupt routine a led connected to PC.06 is toggled. This led will be toggled due to the softawre interrupt generated on EXTI Line9 then at each falling edge.
标签: configure interrupt external example
上传时间: 2016-11-17
上传用户:GavinNeko
Hid Led Tester is a simple USB(interrupt mode)device tester package. There are firmware and software in it. Hid Led tester follows USB HID protocol, we don’t need to install driver for the device, and Windows (Win 2000 and later) will install the device automatic.
标签: interrupt firmware software package
上传时间: 2014-01-02
上传用户:llandlu
A Programmer s Reference to BIOS, DOS, and Third-Party Calls X86 Interrupt 使用
标签: Third-Party Programmer Interrupt Reference
上传时间: 2013-12-12
上传用户:shus521
RMI asynchronism receive message callback() register and deregister to control update or interrupt
标签: asynchronism deregister interrupt callback
上传时间: 2016-12-20
上传用户:来茴
这是利用atmega对interrupt的程序设计,请参考
上传时间: 2016-12-30
上传用户:zhengzg