The design of battery-powered equipment can often bequite challenging. Since few ICs can operate Directly fromthe end-of-life voltage from a 2-cell battery (about 1.8V),most systems require a DC/DCconverter. The systemdesigner often has a limited area in which to place the DC/DC converter; associated inductors and capacitors must be
上传时间： 2013-11-23
上传用户：wys0120
Digitemp Junior – An RS-232 Port-Powered Digital Thermometer Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it rel- atively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power sup- plies or batteries. It is powered Directly by the RS-232 port.
上传时间： 2013-10-21
上传用户：baitouyu
Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it relatively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power supplies or batteries. It is powered Directly by the RS-232 port.
上传时间： 2013-10-20
上传用户：Maple
详细介绍工控软件组态王与单片机多机串口通讯的设计原理。分析组态王提供的直接与单片机串口通信方法的优点，给出系统基于RS-485总线传输的接口电路原理图。根据组态王提供的通讯协议和单片机多机串口通讯的原理，给出程序设计流程与思路。 Abstract: In this paper，the design principle of communication between multi-SCM and KingView by serial ports is described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM Directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
上传时间： 2013-12-19
上传用户：tecman
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects Directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上传时间： 2013-10-26
上传用户：fengweihao158@163.com
The XL6003 regulator is fixed frequency PWM Boost (step-up) DC/DC converter, capable ofdriving 1050mA load current with excellent line and load regulation. The regulator is simple to use because it includes internal frequency compensation and a fixed-frequency oscillator so that it requires a minimum number of external components to work. The XL6003 could Directly drive 5~10 3W LED units at VIN=12V.
上传时间： 2013-11-07
上传用户：xy@1314
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware Directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
标签： Demonstration 3200 USB for
上传时间： 2014-02-27
上传用户：zhangzhenyu
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 Microcontroller Core. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementation of the USB hardware Directly on the chip, complying with the Universal Serial Bus Specification, Revision 1.1.This application note describes a demonstration program that has been written for the DK3200 hardware demonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to work with the device, using the HID class as a ready-made device driver for the USB connection.
上传时间： 2014-04-03
上传用户：lizhizheng88
The XPS Ethernetlite peripheral does not provide any mechanism to access the Ethernet PHYregisters. These registers are used to configure auto negotiation parameters and to obtain PHYstatus. This application note provides reference systems and associated software to accessPHY registers by connecting the serial management bus signals MDC and MDIO to GPIOswhich the software controls Directly.
上传时间： 2013-10-17
上传用户：JamesB
多远程二极管温度传感器-Design Considerations for pc thermal management Multiple RDTS (remote diode temperature sensing) provides the most accurate method of sensing an IC’s junction temperature. It overcomes thermal gradient and placement issues encountered when trying to place external sensors. PCB component count decreases when using a device that provides multiple inputs.Better temperature sensing improves product performance and reliability. Disk drive data integrity suffers at elevated temperatures. IBM published an article stating that a 5°C rise in operating temperature causes a 15% increase in the drive’s failure rate. The overall performance of a system can be improved by providing a more accurate temperature measurement of the most critical devices allowing them to run just a few degrees hotter.The LM83 Directly senses its own temperature and the temperature of three external PN junctions. One is dedicated to the CPU of choice, the other two go to other parts of your system that need thermal monitoring such as the disk drive or graphics chip. The SMBus-compatible LM83 supports SMBus timeout and logic levels. The LM83 has two interrupt outputs; one for user-programmable limits and WATCHDOG capability (INT), the other is a Critical Temperature Alarm output (T_CRIT_A) for system power supply shutdown.
标签： Considerat Design 远程 二极管
上传时间： 2014-12-21
上传用户：ljd123456
