Abstract: This Design idea explains how to implement an 8-bit analog-to-digital converter (ADC), using a microcontroller
上传时间： 2013-10-30
上传用户：爱死爱死
Abstract: A perfect voltage reference produces a stable voltage independent of any external factors. Real-world voltagereferences, of course, are subject to errors caused by many external factors. One causeof these major errors istemperature. Without care, it is easy to operate a voltage reference outside its operating temperature range. Thisapplication note describes how references respond to temperature changes, and how self-heating can cause a voltagereference to operate outside its recommended temperature range. Once understood, this knowledge can then be used toavoid making this Design error.
上传时间： 2013-11-08
上传用户：xianglee
平行耦合微带线带通滤波器在微波电路系统中广泛应用。为了提高带通滤波器性能，缩短设计周期，采用奇偶模原理分析与ADS（Advanced Design System）仿真相结合的方法，设计出一个中心频率为2.5 GHz，相对带宽为10%的平行耦合微带线带通滤波器。进一步优化参数，得到电路版图。最终结果证明，这种方法具有设计周期短、可靠性高的特点，且各项参数满足设计要求。
上传时间： 2013-10-12
上传用户：jrsoft
Abstract: A laser module Designer can use a fixed resistor, mechanical pot, digital pot, or a digital-to-analogconverter (DAC) to control the laser driver's modulation and bias currents. The advantages of a programmablemethod (POT or DAC) are that the manufacturing process can be automated and digital control can be applied(e.g., to compensate for temperature). Using POTs can be a more simple approach than a DAC. There can be aslight cost advantage to using a POT, but this is usually not significant relative to other pieces of the Design.Using a DAC can offer advantages, including improved linearity (translating to ease of software implementationand ability to hit the required accuracy), increased board density, a wider range of resolutions, a betteroptimization range, ease of use with a negative voltage laser driver, and unit-to-unit consistency
上传时间： 2013-11-13
上传用户：ca05991270
This document and the associated reference Design provide guidance for assigning anddebugging software to or in FLASH memory, specifically for a MicroBlaze™ embeddedprocessor Design.
上传时间： 2013-11-11
上传用户：dgann
Photodiodes can be broken into two categories: largearea photodiodes with their attendant high capacitance(30pF to 3000pF) and smaller area photodiodes withrelatively low capacitance (10pF or less). For optimalsignal-to-noise performance, a transimpedance amplifi erconsisting of an inverting op amp and a feedback resistoris most commonly used to convert the photodiode currentinto voltage. In low noise amplifi er Design, large areaphotodiode amplifi ers require more attention to reducingop amp input voltage noise, while small area photodiodeamplifi ers require more attention to reducing op amp inputcurrent noise and parasitic capacitances.
上传时间： 2013-10-28
上传用户：hanbeidang
Digital-to-analog converters (DACs) are prevalent inindustrial control and automated test applications.General-purpose automated test equipment often requiresmany channels of precisely controlled voltagesthat span several voltage ranges. The LTC2704 is ahighly integrated 16-bit, 4-channel DAC for high-endapplications. It has a wide range of features Designed toincrease performance and simplify Design.
上传时间： 2013-11-22
上传用户：元宵汉堡包
Recent advances in low voltage silicon germaniumand BiCMOS processes have allowed the Design andproduction of very high speed amplifi ers. Because theprocesses are low voltage, most of the amplifi er Designshave incorporated differential inputs and outputs to regainand maximize total output signal swing. Since many lowvoltageapplications are single-ended, the questions arise,“How can I use a differential I/O amplifi er in a single-endedapplication?” and “What are the implications of suchuse?” This Design Note addresses some of the practicalimplications and demonstrates specifi c single-endedapplications using the 3GHz gain-bandwidth LTC6406differential I/O amplifi er.
上传时间： 2013-11-23
上传用户：rocketrevenge
The Reactor Design pattern handles service requests that are delivered concurrently to an application by one or more clients. Each service in an application may consist of serveral methods and is represented by a separate event handler that is responsible for dispatching service-specific requests.
上传时间： 2013-10-15
上传用户：libinxny
This note describes some of the unique IC Design techniques incorporated into a fast, monolithic power buffer, the LT1010. Also, some application ideas are described such as capacitive load driving, boosting fast op amp output current and power supply circuits.
上传时间： 2013-11-12
上传用户：671145514
