建立用于完成复数算术运算的类Complex。编写一个程序测试该类。
上传时间： 2017-06-19
上传用户：lifangyuan12
Hardware random number generators attempt to extract randomness directly from Complex physical systems. In this way they create random outputs without requiring any seed inputs. In this paper we describe how to use Physical Random Functions (or Physical Unclonable Functions, PUFs) to create a candidate hardware random number generator.
标签： generators randomness Hardware directly
上传时间： 2013-12-20
上传用户：缥缈
定义一个复数类Complex，使得下面的代码能够工作 Complex c1(3,5); // 用复数3+5i初始化c1 Complex c2 = 4.5; // 用实参4.5初始化c2 c1.add(c2); // 将c1与c2相加，结果保存在c1中 c1.show(); // 将c1输出（这时结果应该是7.5+5i）
上传时间： 2016-05-17
上传用户：拉梅系数
进入20世纪90年代后，随着全球信息化、智能化、网络化的发展，嵌入式系统技术获得了前所未有的发展空间。 嵌入式系统的最大特点之_是其所具有的目的性或针对性，即每一套嵌入式系统的开发设计都有其特殊的应用场合与特定功能，这也是嵌入式系统与通刚的计算机系统最主要的区别。由于嵌入式系统是为特定的目的而设计的，且常常受到体积、成本、功能、处理能力等各种条件的限制。因此，如果可以最大限度地提高应用系统硬件上和软件上的灵活性，就可以用最低的成本，最少的时间，快速的完成功能的转换。 本课题的目的在于提出并设计一种基于ARM(Advanced RISC Machines)和CPLD(Complex Programmable Logic Device)的可扩展功能嵌入式系统平台，并完成了系统的硬件设计和PCI(Peripheral Component Interconnect)桥的固件设计。设计过程中采用美国ALTIUM公司的ALTIUM DESIGNER 6.0 EDA软件开发了系统的硬件部分。在整个硬件开发环节中，充分采用高速PCB(Printed Circuit Board)的设计原则，并进行全面的电路仿真试验，保证了硬件系统的高度可靠性。本系统承袭了ARM7系列处理器高性能、低功耗、低成本的优点，并充分考虑到用户的需要，扩展了多种常用的外部设备接口以及蓝牙无线接口等，为将米各种可能的应用提供了完善的硬件基础。概括总结起来本文具体工作如下： 1．完全自主设计了具有高扩展性的基于LPC2292嵌入式处理器的嵌入式系统应用开发平台。基于该硬件平台，可以实现许多基于ARM架构处理器的嵌入式应刚而无需对硬什系统作出大的改变，如多协议转换器、CAN(Control Area Network)总线网关、以太网关、各种工业控制应用等。并在具体的设计实践中，总结出了嵌入式系统硬件平台的设计原则及设计方法。 2．完成了基于CPLD的PCI桥接芯片的同什设计，在ARM硬件平台上成功扩展了PCI设备，成功解决了ARM处理器和PCI从设备之间通讯的问题。 3．完成了对所开发的嵌入式系统硬件平台的测试工作，完成了基于AT89C51的PCI测试卡软硬件设计。基于此测试卡，可以实现对系统中的PCI通讯功能进行有效测试，以保证整个硬件系统正常、高效、稳定地运行。本系统的设计完成，使其可以作为嵌入式应用的二次开发或实验平台，用于工业产品开发及高校相关专业的实践教学。
上传时间： 2013-05-21
上传用户：sztfjm
Abstract: Using a wafer-level package (WLP) can reduce the overall size and cost of your solution.However when using a WLP IC, the printed circuit board (PCB) layout can become more Complex and, ifnot carefully planned, result in an unreliable design. This article presents some PCB designconsiderations and general recommendations for choosing a 0.4mm- or 0.5mm-pitch WLP for yourapplication.
标签： Considerations Guidelines and Design
上传时间： 2013-10-14
上传用户：ysystc699
Many Complex systems—such as telecom equipment,memory modules, optical systems, networking equipment,servers and base stations—use FPGAs and otherdigital ICs that require multiple voltage rails that muststart up and shut down in a specific order, otherwise theICs can be damaged. The LTC®2924 is a simple andcompact solution to power supply sequencing in a 16-pinSSOP package (see Figures 1 and 2).
上传时间： 2013-10-28
上传用户：tonyshao
A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered applications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, Complex magnetics,polarity inversion and/or circuit Complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
上传时间： 2013-10-21
上传用户：ljt101007
Once relegated to the hinterlands of low cost indicatorlights, the LED is again in the spotlight of the lightingworld. LED lighting is now ubiquitous, from car headlightsto USB-powered lava lamps. Car headlights exemplifyapplications that capitalize on the LED’s clear advantages—unwavering high quality light output, tough-assteelrobustness, inherent high effi ciency—while a USBlava lamp exemplifi es applications where only LEDs work.Despite these clear advantages, their requirement forregulated voltage and current make LED driver circuitsmore Complex than the venerable light bulb, but some newdevices are closing the gap. For instance, the LTM®8040μModule™ LED driver integrates all the driver circuitryinto a single package, allowing designers to refocus theirtime and effort on the details of lighting design criticalto a product’s success.
上传时间： 2013-10-16
上传用户：togetsomething
In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more Complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during DC to DC conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
上传时间： 2013-11-24
上传用户：defghi010
As logic systems get larger and more Complex, theirsupply current requirements continue to rise. Systemsrequiring 100A are fairly common. A high current powersupply to meet such requirements usually requires parallelingseveral power regulators to alleviate the thermalstress on the individual power components. A powersupply designer is left with the choice of how to drive theseparalleled regulators: brute-force single-phase or smartPolyPhaseTM.
上传时间： 2013-10-08
上传用户：zhqzal1014
