Circular convolution using 6713 tms320 kit
标签： convolution Circular using 6713
上传时间： 2013-12-24
上传用户：天诚24
Circular convolution code in matlab
标签： convolution Circular matlab code
上传时间： 2017-07-01
上传用户：pompey
Circular Buffer / Queue immplementation
标签： immplementation Circular Buffer Queue
上传时间： 2013-12-24
上传用户：huannan88
source code c54x FIR filter with Circular addressing
标签： addressing Circular source filter
上传时间： 2017-08-17
上传用户：hebmuljb
基于幅移键控技术ASK（Amplitude-Shift Keying），以C8051F340单片机作为监测终端控制器，C8051F330D单片机作为探测节点控制器，采用半双工的通信方式，通过监控终端和探测节点的无线收发电路，实现数据的双向无线传输。收发电路采用直径为0.8 mm的漆包线自行绕制成圆形空心线圈天线，天线直径为（3.4±0.3）cm。试验表明，探测节点与监测终端的通信距离为24 cm，通过桥接方式，节点收发功率为102 mW时，节点间的通信距离可达20 cm。与传统无线收发模块相比，该无线收发电路在受体积、功耗、成本限制的场合有广阔的应用前景。 Abstract: Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm Circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
上传时间： 2013-10-19
上传用户：xz85592677
The view238 application is a simple tool for graphically displaying STEP-NC toolpaths. It is a Java application that reads AP-238 XML data using the DOM inferface, then finds and display the toolpaths within. At present, only polylines, and Circular arcs are processed.
标签： application graphically displaying toolpaths
上传时间： 2013-12-02
上传用户：zhangliming420
These Simulink blocks contain transfer functions that model the pressure and flow transients for axisymmetric 2D viscous flow of a compressible fluid in a straight rigid Circular cross section pipelines. Three models are available: (1) pressures at the ends (2) flow rates at the ends (3) pressure at one end and flow rate at the other Filtering is incorporated to reduce numerical oscillation (Gibbs phenomenon). See J. Dyn. Systems, Meas. & Control vol 122 (2000) pp. 153-162.
标签： transients functions Simulink transfer
上传时间： 2014-01-22
上传用户：Shaikh
This example describes how to use the ADC and DMA to transfer continuously converted data from ADC to a data buffer. The ADC is configured to converts continuously ADC channel14. Each time an end of conversion occurs the DMA transfers, in Circular mode, the converted data from ADC1 DR register to the ADC_ConvertedValue variable. The ADC1 clock is set to 14 MHz.
标签： continuously ADC describes converted
上传时间： 2014-01-03
上传用户：徐孺
usb bulk 传输例程。 * The bulkusb driver is a generic function driver, based on the Windows Driver Model (WDM). * Supports Plug and Play(PnP), Power Management(PM), Windows Management Instrumentation (WMI) and the Selective Suspend (SS) features. * This sample is based off the selSusp DDK sample. Please refer the selSusp sample and the DDK docs to understand the handling of PnP, PM, WMI and SS features and implementations. * The USB device used for this sample is a generic Intel I82930 USB evaluation board programmed with a simple loopback test using a 64 KB Circular buffer. None of the code in the sample is specific to this controller chip.
标签： driver function Windows bulkusb
上传时间： 2016-04-25
上传用户：270189020
cordic methods describe essentially the same algorithm that with suitably chosen inputs can be used to calculate a whole range of scientific functions including sin, cos, tan, arctan, arcsin, arccos, sinh, cosh, tanh, arctanh, log, exp, square root and even multiply and divide. the method dates back to volder [1959], and due to its versatility and compactness, it made possible the microcoding of the hp35 pocket scientific calculator in 1972. here is some code to illustrate the techniques. ive split the methods into three parts linear, Circular and hyperbolic. in the hp35 microcode these would be unified into one function (for space reasons). because the linear mode can perform multiply and divide, you only need add/subtract and shift to complete the implementation. you can select in the code whether to do the multiples and divides also by cordic means. other multiplies and divides are all powers of 2 (these dont count). to eliminate these too, would involve ieee hackery.
标签： essentially algorithm describe suitably
上传时间： 2017-03-02
上传用户：litianchu
