Using the XGATE for Manchester DecodingTable of Contents 1 Introduction 1.1 XGATE Module in S12X 2 Decoding Algorithm 3 Software Implementation 3.1 Frame Scheme 3.2 Operating Modes and Demo 3.3 Files Summary 3.4 Complete Mode Flowchart 4 Manchester Encoder 4.1 Devices Used 5 Conclusion Appendix A Noise Elements During RF Transmissions in the Manchester Decoding ImplementationA.1 Types of Noise A.2 Effects of Noise A.3 Workaround for Noise Effects
标签： Manchester XGATE 译码
上传时间： 2013-10-15
上传用户：wqq123456
The PAM2862 is a continuous mode inductivestep-down converter, designed for driving singleor multiple series connected LEDs efficientlyfrom a voltage source higher than the LEDvoltage. The device operates from an inputupply between 6V and 30V and provides anexternally adjustable output current of up to 1A.Depending upon supply voltage and externalcomponents, this can provide up to 24 watts ofoutput power.
上传时间： 2013-11-16
上传用户：司令部正军级
The PCA9670 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9670 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-15
上传用户：stella2015
The PCA9671 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plus(Fm+) family.The PCA9671 is a drop in upgrade for the PCF8575 providing higher I2C-bus speeds(1 MHz versus 400 kHz) so that the output can support PWM dimming of LEDs, higherI2C-bus drive (30 mA versus 3 mA) so that many more devices can be on the bus withoutthe need for bus buffers, higher total package sink capacity (400 mA versus 100 mA) thatsupports having all 25 mA LEDs on at the same time and more device addresses (64versus 8) to allow many more devices on the bus without address conflicts.
上传时间： 2013-10-12
上传用户：laomv123
The PCA9672 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9672 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-23
上传用户：jasonheung
The PCA9673 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9673 is a drop in upgrade for the PCF8575 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(400 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-29
上传用户：wkchong
The PCA9674/74A is a drop-in upgrade for the PCF8574/74A providing higher Fast-modePlus I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-22
上传用户：wwwwwen5
The TL2575 and TL2575HV represent superior alternatives to popular three-terminal linear regulators. Due totheir high efficiency, the devices significantly reduce the size of the heatsink and, in many cases, no heatsink isrequired. Optimized for use with standard series of inductors available from several different manufacturers, theTL2575 and TL2575HV greatly simplify the design of switch-mode power supplies by requiring a minimaladdition of only four to six external components for operation.
标签： STEP-DOWN SWITCHING SIMPLE 1A
上传时间： 2013-11-20
上传用户：jelenecheung
摘要：本水位监测报警器使用5V低压直流电源（也可以用3节5号电池代替）就可以对5~15厘米的水位进行监测，用LED显示和数码管显示水位，并可以对不再此范围内的水位发出报警。主要采用CD4066、74LS86、74LS32、CD4511芯片，再加上数码管、蜂鸣器、发光二极管、电阻这些器件组成一个简单而灵敏的监测报警电路，操作简单，接通电源即可工作。因为大部分电路采用数字电路，所以本水位监测报警器还具有耗能低、准确性高的特点。关键字：译码电路 报警电路 监测电路 Abstract: The water level alarm monitoring the use of 5 V low-voltage DC power (can also use three batteries replaced on the 5th) will be able to 5 to 15 centimeters of water level monitoring, with LED display and digital display of water level, and this can no longer Within the scope of a water level alarm. Mainly CD4066, 74LS86, 74LS32, CD4511 chips, coupled with digital control, buzzer, light-emitting diode, the resistance of these devices composed of a simple and sensitive monitoring alarm circuits. Because the majority of circuits using digital circuitry, so the water level monitored alarm system also has low energy consumption, high accuracy of the characteristics. Keyword: Decoding circuit alarm circuit monitoring circuit
上传时间： 2013-11-05
上传用户：王庆才
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
