在开放式数控系统结构模型的基础上，研究了基于ISA总线的DSP通信控制原理。采用中断方式完成了PC机和DSP之间的通信。介绍了以DriverWorks为工具开发ISA设备WDM驱动程序的方法，探讨了中断处理、驱动程序与应用程序之间的通信,简要说明了驱动程序的安装与调试。通过调试,系统设计运行稳定。 Abstract: The ISA bus and DSP correspondence control principle is investigated in the basis of the existing open architecture numerical control system.The interrupt method is used to realize the communication between PC and DSP based on the ISA bus.The methods of WDM driver exploitation for ISA device using Driver Works are introduced.The main process of driver program and the keys such as handle interrupt and the communication between the drivers and application are presented.And how to debug and install the drive is explained.
上传时间： 2013-11-04
上传用户：kang1923
为了解决磁放大器性能测试过程中，需要对其供给不同数值恒定电流的问题，设计了一种基于DAC7512和单片机的数控恒流源系统。该系统采用AT89C51作为主控器件，将计算机发送的电流控制字命令转换为D/A转换器控制字，通过模拟SPI通信接口，写D/A控制字到DAC7512，从而控制其输出相应数字电压值，经差动缩放电路、电压/电路变换电路和功率驱动电路，最后输出恒定电流。实验结果表明，恒流源输出电流调节范围为-45~+45 mA、精度为±0.1 mA，分辨率达0.024 4 mA，具有应用灵活，外围电路简单，可靠性高的特点。该数控直流恒流源也可为相关产品的测试系统研发提供参考。 Abstract: In order to solve the need to supply different values constant current for the magnetic amplifier in testing process， numerical control constant current source system was designed based on DAC7512 chip and microcontroller technology. The system used the AT89C51 as the main chip， which can convert the current control word from computer into to D/A control words. And the system wrote D/A control word into the DAC7512 chip to control the output voltage value by the SPI communication interface， which can output corresponding constant current figures by scaling circuit， the V/I converter and power drive circuit. Experimental results show that the current source output current adjustment range is -45~+45mA， accuracy is ± 0.1mA， and resolution ratio is 0.024 4mA
上传时间： 2014-12-27
上传用户：invtnewer
针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移，一般采用光电轴角编码器检测位置信号，输出正交编码脉冲信号。若采用其他方法检测位置信号，必然导致电路设计复杂，可靠性降低。因此，提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理，LS7266R1与单片机的接口硬件设计，以及主程序软件流程图。巧妙地把力量传感器，位移传感器等机械运动状态的压力或拉力以及位置坐标，变成了电压信号和电脉冲数字信号，供A/D测量和LS7266R1计数，从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上传时间： 2013-11-02
上传用户：yl1140vista
Virtex-5, Spartan-DSP FPGAs Application Note This application note demonstrates how efficient implementations of Digital Up Converters(DUC) and Digital Down Converters (DDC) can be done by leveraging the Xilinx DSP IPportfolio for increased productivity and reduced time to development. Step-by-step instruction is given on how to perform system-level trade off analysis and develop the most efficient FPGA implementation, thus allowing engineers a flexible, low-cost and low-power alternative to ASSP technologies.
标签： Spartan-DSP Virtex FPGAs Ap
上传时间： 2013-10-23
上传用户：raron1989
汇编器在微处理器的验证和应用中举足轻重，如何设计通用的汇编器一直是研究的热点之一。本文提出了一种开放式的汇编器系统设计思想，在汇编语言与机器语言间插入中间代码CMDL（code mapping description language）语言，打破汇编语言与机器语言的直接映射关系，由此建立起一套描述汇编语言与机器语言的开放式映射体系。基于此开放式映射体系开发了一套汇编器系统，具有较高层次上的通用性和可移植性。【关键词】指令集，CMDL，汇编器，开放式 Design of Retargetable Assembler System Liu Ling Feng Wen Nan Wang Ying Chun Jiang An Ping Ji Li Jiu IME of Peking University, 100871【摘要】An assembler plays a very important role in the field of microprocessor verifications and applications, thus how to build a retargetable assembler system has been a hotspot in this field for long time. This paper presents a new method about the retargetable assembler system design.It provides a kind of language CMDL, code mapping description language. During the process of assembling, assembler languages are firstly translated to CMDL, and then mapped to the machine codes. In an other word, CMDL is inserted between assembler languages and machine codes during the translation procedure. As a medium code, CMDL has a lot of features, such as high extraction, strong descript capabilities. It can describe almost all attributes of assembler languages. By breaking the direct mapping relationship between assembler languages and machine codes, the complexities of machine codes are hided to the users, therefore, the new retargetable assembler system has higher retargetable level by converting the mapping from assembler languages and machine codes to assembler languages and CMDL, and implementationof it becomes easier. Based on the new mapping system structure, a retargetable assemblersystem is developed. It proved the whole system has good retargetability and implantability.【关键词】instruction set, symbol table, assembler, lexical analysis, retargetability
上传时间： 2013-10-10
上传用户：meiguiweishi
本文依据集成电路设计方法学，探讨了一种基于标准Intel 8086 微处理器的单芯片计算机平台的架构。研究了其与SDRAM，8255 并行接口等外围IP 的集成，并在对AMBA协议和8086 CPU分析的基础上，采用遵从AMBA传输协议的系统总线代替传统的8086 CPU三总线结构，搭建了基于8086 IP 软核的单芯片计算机系统，并实现了FPGA 功能演示。关键词：微处理器； SoC；单芯片计算机；AMBA 协议 Design of 8086 CPU Based Computer-on-a-chip System（School of Electrical Engineering and Automation, Heifei University of Technology, Hefei, 230009,China）Abstract: According to the IC design methodology, this paper discusses the design of one kind of Computer-on-a-chip system architecture, which is based on the standard Intel8086 microprocessor,investigates how to integrate the 8086 CPU and peripheral IP such as, SDRAM controller, 8255 PPI etc. Based on the analysis of the standard Intel8086 microprocessor and AMBA Specification,the Computer-on-a-chip system based on 8086 CPU which uses AMBA bus instead of traditional three-bus structure of 8086 CPU is constructed, and the FPGA hardware emulation is fulfilled.Key words: Microprocessor; SoC; Computer-on-a-chip; AMBA Specification
上传时间： 2013-12-27
上传用户：kernor
在综合分析谐波励磁无刷同步发电机励磁控制系统的基础上,对其励磁控制策略进行了研究,开发了一套基于DSP( TMS320F2812) 控制的新型柴油发电机励磁控制系统,该系统采用参数自适应模糊PID 控制励磁,选用交流采样方式实时检测各信号的瞬时特性,系统仿真结果以及在1 台25 kW 工频柴油发电机上的试验结果证明了该控制器具有较好的电压调节特性,系统稳态和暂态性能完全满足发电机对励磁系统的要求。关键词:励磁调节;模糊PID 控制;数字信号处理器;交流采样 Abstract :According to the general analysis of the excitation cont rol system of the harmonious wave excitation brushless synchronous generator and it s characteristics ,a new type of diesel generator excitation cont rol system based on DSP( TMS320F2812) was designed. An adaptive fuzzy PID cont rol of excitation is used in this system. To detect the t ransient characteristics of the signals in a timely manner ,AC sampling was applied.The system simulation result s and the testing result s f rom a 25 kW diesel generator (50 Hz) can prove that the voltage regulation characteristics of the excitation cont rol system are very well ,and both the steadyOstate performance and the t ransient performance of the generator are also good.Key words :excitation cont rol ;fuzzy PID cont rol ;digital signal processor (DSP) ;AC sampling
上传时间： 2013-10-29
上传用户：fxf126@126.com
摘 要 瞬态仿真领域的许多工作需要获得可视化数据, 仿真电路不能将输出参数绘制成图形时研究工作将受到很大影响. 而权威电路仿真软件PSpice 在这个方面不尽如人意. 本文提出了一种有效的解决办法: 通过MATLAB 编程搭建一个PSpice 与MATLAB 的数据接口,使PSpice输出数据文件可以导入到MATLAB中绘制图形. 这令我们能够很方便地获得数据的规律以有效地分析仿真结果, 这项技术对于教学和工程实践都有比较实际的帮助.关键词: 瞬态仿真 仿真程序 PSpice MATLAB 可视化数据The Data Transfer from Pspice to MATLABWu hao Ning yuanzhong Liang yingAbstract Many works in the area of transient simulation has shown how a emulator such asPSpice can be interfaced to an control analysis package such as MATLAB to get viewdata. Thepaper describes how such interfaces can be made using the MATLAB programming. The platformas a typical platform will solve the problem that PSpice software sometimes can not draw the datato a picture. It can make us find the rule from numerous data very expediently, so we can analyzethe outcome of the simulation. And it also can be used in the field of education.Keywords Transient Simulation Emulator PSpice MATLAB Viewdata1 引言科学研究和工程应用常需要进行电路仿真 PSpice可进行直流 交流 瞬态等基本电路特性分析 也可进行蒙托卡诺 MC 统计分析 最坏情况 Wcase 分析 优化设计等复杂电路特性分析 它是国际上仿真电路的权威软件 而MATLAB的主要特点有 高效方便的矩阵和数组运算 编程效率高 结构化面向对象 方便的绘图功能 用户使用方便 工具箱功能强大 两者各有着重点 两种软件结合应用 对研究工作有很重要的意义香港理工大学Y. S. LEE 等人首先将PSpice和MATLAB结合 开发了电力电子电路优化用的CAD 程序MATSPICE[6] 将两者相结合的关键在于 如何用MATLAB 获取PSpice的仿真数据 对此参考文献 6 里没有详细叙述 本文着重说明用MATLAB 读取PSpice仿真数据的具体方法本论文利用MATLAB对PSpice仿真出的数据处理绘制出后者无法得到或是效果不好的仿真图形 下面就两者结合使用的例子 进行具体说明
上传时间： 2013-10-20
上传用户：wuchunzhong
This application note describes how to implement the Bus LVDS (BLVDS) interface in the supported Altera ® device families for high-performance multipoint applications. This application note also shows the performance analysis of a multipoint application with the Cyclone III BLVDS example.
标签： Implementing LVDS 522 Bus
上传时间： 2013-11-10
上传用户：frank1234
针对嵌入式机器视觉系统向独立化、智能化发展的要求，介绍了一种嵌入式视觉系统--智能相机。基于对智能相机体系结构、组成模块和图像采集、传输和处理技术的分析，对国内外的几款智能相机进行比较。综合技术发展现状，提出基于FPGA+DSP模式的硬件平台，并提出智能相机的发展方向。分析结果表明，该系统设计可以实现脱离PC运行，完成图像获取与分析，并作出相应输出。 Abstract: This paper introduced an embedded vision system-intelligent camera ，which was for embedded machine vision systems to an independent and intelligent development requirements. Intelligent camera architecture， component modules and image acquisition， transmission and processing technology were analyzed. After comparing integrated technology development of several intelligent cameras at home and abroad， the paper proposed the hardware platform based on FPGA+DSP models and made clear direction of development of intelligent cameras. On the analysis of the design， the results indicate that the system can run from the PC independently to complete the image acquisition and analysis and give a corresponding output.
上传时间： 2013-10-24
上传用户：bvdragon
