Keil C51 UV2调试命令（中文版）
上传时间： 2014-07-19
上传用户：wangjin2945
AT系列单片机烧写器
上传时间： 2013-10-17
上传用户：xanxuan
针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移，一般采用光电轴角编码器检测位置信号，输出正交编码脉冲信号。若采用其他方法检测位置信号，必然导致电路设计复杂，可靠性降低。因此，提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理，LS7266R1与单片机的接口硬件设计，以及主程序软件流程图。巧妙地把力量传感器，位移传感器等机械运动状态的压力或拉力以及位置坐标，变成了电压信号和电脉冲数字信号，供A/D测量和LS7266R1计数，从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上传时间： 2013-11-02
上传用户：yl1140vista
Designing Boards with Atmel AT89C51, AT89C52, AT89C1051, and AT89C2051 for Writing Flash at In-Circuit Test:Recent improvements in chips andtesters have made it possible for thetester to begin taking over the role traditionallyassigned to the PROM programmer.Instead of having a PROM programmerwrite nonvolatile memoriesbefore assembling the board, the in-circuittester writes them during in-circuittesting operations. Many Teradyne Z18-series testers are now in use loadingcode into nonvolatile memories, microcontrollersand in-circuit programmable logic devices. The purpose of this note is to explain how the Z18 approaches the writing task for Atmel AT89C series IC’s,so that designers of boards using these chips can get the best results.
标签： Designing Boards Atmel with
上传时间： 2013-11-20
上传用户：lijianyu172
上一讲中我们学习了如何建立工程、汇编、连接工程，并获得目标代码，但是做到这一步仅仅代表你的源程序没有语法错误，至于源程序中存在着的其它错误，必须通过调试才能发现并解决，事实上，除了极简单的程序以外，绝大部份的程序都要通过反复调试才能得到正确的结果，因此，调试是软件开发中重要的一个环节，这一讲将介绍常用的调试命令、利用在线汇编、各种设置断点进行程序调试的方法，并通过实例介绍这些方法的使用。
上传时间： 2014-04-14
上传用户：sdq_123
思科交换机配置命令大全
上传时间： 2014-12-29
上传用户：gaojiao1999
华为交换机配置命令大全
上传时间： 2013-10-26
上传用户：181992417
uinterface fastethernet slot-number/interface-number 该命令用于指定一个快速以太网接口，并进入该接口的配置模式 uip address ip-address subnet-mask [secondary] uno ip address [ip-address subnet-mask] [secondary] 设置接口的IP地址和子网掩码。使用 no 选项可删除接口的IP地址。 uShutdown 和no shutdown
上传时间： 2014-12-02
上传用户：qwe1234
UNIX系统操作命令大全
上传时间： 2013-11-18
上传用户：qq527891923
linux常用命令
上传时间： 2013-10-18
上传用户：zhangyi99104144
