Abstract: Designers who must interface 1-Wire temperature sensors with Xilinx field-programmable gate arrays(FPGAs) can use this reference design to drive a DS28EA00 1-Wire slave device. The downloadable softwarementioned in this document can also be used as a starting point to connect other 1-Wire slave devices. The systemimplements a 1-Wire master connected to a UART and outputs temperature to a PC from the DS28EA00 temperaturesensor. In addition, high/low alarm outputs are displayed from the DS28EA00 PIO pins using LEDs.
标签： PicoBlaze Create Master Xilinx
上传时间： 2013-11-05
上传用户：a6697238
AstroII-EVB-F1K(A)-L144开发板用户指南
标签： AstroII-EVB-F 144 开发板 用户
上传时间： 2013-11-22
上传用户：zhichenglu
Abstract: This application note discusses the development and deployment of 3G cellular femtocell base stations. The technicalchallenges for last-mile residential connectivity and adding system capacity in dense urban environments are discussed, with 3Gfemtocell base stations as a cost-effective solution. Maxim's 3GPP TS25.104-compliant transceiver solution is presented along withcomplete radio reference designs such as RD2550. For more information on the RD2550, see reference design 5364, "FemtocellRadio Reference Designs Using the MAX2550–MAX2553 Transceivers."
标签： Base-Station Applications Single-Chip Transceiver
上传时间： 2013-11-07
上传用户：songrui
This application note covers the design considerations of a system using the performance features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The design focuses on high system throughput through the AXI Interconnect core with F MAX and area optimizations in certain portions of the design. The design uses five AXI video direct memory access (VDMA) engines to simultaneously move 10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary video timing signals. Data read by each AXI VDMA is sent to a common on-screen display (OSD) core capable of multiplexing or overlaying multiple video streams to a single output video stream. The output of the OSD core drives the DVI video display interface on the board. Performance monitor blocks are added to capture performance data. All 10 video streams moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are controlled by a MicroBlaze™ processor. The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the Xilinx® ML605 Rev D evaluation board
上传时间： 2013-11-14
上传用户：fdmpy
特点 精确度0.25%滿刻度 ±1位數 输入配线系统可任意选择 CT比可任意设定 具有异常电流值与异常次数记录保留功能 电流过高或过低检测可任意设定 报警继电器复归方式可任意設定 尺寸小,穩定性高 2.主要規格 辅助电源: AC110V&220V ±20%(50 or 60Hz) AC220V&440V ±20%(50 or 60Hz)(optional) 精确度: 0.25% F.S. ±1 digit 输入负载: <0.2VA (Current) 最大过载能力 : Current related input: 2 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1 sec. 输入电流范围: AC0-5A (10-1000Hz) CT ratio : 1-2000 adjustable 启动延迟动作时间: 0-99.9 second adjustable 继电器延迟动作时间: 0-99.9 second adjustable 继电器复归方式: Manual (N) / latch(L) can be modified 继电器磁滞范围: 0-999 digit adjustable 继电器动作方向: HI /LO/GO/HL can be modified 继电器容量: AC 250V-5A, DC 30V-7A 过载显示: "doFL" 温度系数: 50ppm/℃ (0-50℃) 显示幕: Red high efficiency LEDs high 14.22mm(.56")(PV) Red high efficiency LEDs high 14.22mm(.276")(NO) 参数设定方式: Touch switches 记忆型式 : Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc(input/output 使用环境条件 : 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-10-14
上传用户：wanghui2438
特点 精确度0.1%滿刻度 ±1位數 可量測 交直流電流/交直流电压/電位計/傳送器/Pt-100/荷重元/電阻 等信号 显示范围-1999-9999可任意规划 具有异常值与异常次数记录保留功能 异常信号过高或过低或范围內或范围外检测可任意設定 报警继电器复归方式可任意設定 尺寸小,穩定性高 2.主要規格 精确度: 0.1% F.S. ±1 digit 0.2% F.S. ±1 digit(AC) 取样时间: 16 cycles/sec. 显示值范围: -1999 - +9999 digit adjustable 启动延迟动作时间: 0-99.9 second adjustable 继电器延迟动作时间: 0-99.9 second adjustable 继电器复归方式: Manual (N) / latch(L) can be modified 继电器动作方向: HI /LO/GO/HL can be modified 继电器容量: AC 250V-5A, DC 30V-7A 过载显示: "doFL" 温度系数: 50ppm/℃ (0-50℃) 显示幕: Red high efficiency LEDs high 14.22mm(.56")(PV) Red high efficiency LEDs high 7.0mm(.276")(NO) 参数设定方式: Touch switches 记忆型式 : Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc(input/output 使用环境条件 : 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-02
上传用户：fandeshun
特点 最高輸入頻率 10KHz 计数速度 50/10000脈波/秒可选择 四种输入模式可选择(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 输入脈波具有预设刻度功能 计数暂时停止功能 3组报警功能 15BIT类比输出功能 数位RS-485界面 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <10KHz (up,down,up/down mode) <3KHz (quadrature mode) 输出动作时间 : 0.1 to 99.9 second adjustable 输出复归方式: Manual(N) or automatic (R or C) can be modif 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: -199999 to 999999 类比输出解析度: 15 bit DAC 输出反应速度: < 1/f+10ms(0-90%) 输出负载能力: < 10mA for voltage mode < 10V for current mode <[(V+)-7.5V]/20mA for two-wire mode 输出之涟波: < 0.1% F.S. 通讯位址: "01"-"FF" 传输速度: 19200/9600/4800/2400 selective 通信协议: Modbus RTU mode 显示幕: Red high efficiency LEDs high 14.22mm (.56") 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-23
上传用户：redmoons
特点 精确度0.1%滿刻度 可輸入交直流電流/交直流电压/電位計/傳送器...等信号 16 BIT类比输出功能 输入与输出绝缘耐压2仟伏特/1分钟 宽范围交直流兩用電源设计 尺寸小,穩定性高 2主要規格 精确度: 0.1% F.S. (23 ±5℃) 显示值范围: 0-±19999 digit adjustable 类比输出解析度: 16 bit DAC 输出反应速度: < 250 ms (0-90%)(>10Hz) 输出负载能力: < 10mA for voltage mode < 10V for current mode 输出之涟波: < 0.1% F.S. 归零调整范围: 0- ±9999 Digit adjustable 最大值调整范围: 0- ±9999 Digit adjustable 温度系数: 50ppm/℃ (0-50℃) 显示幕: Red high efficiency LEDs high 10.16mm (0.4") 隔离特性: Input/Output/Power/Case 参数设定方式: Touch switches 记忆方式: Non-volatile E2PROM memory 绝缘抗阻: >100Mohm with 500V DC 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-60℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) 安装方式: Socket/plugin type with barrier terminals CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2014-01-05
上传用户：eastgan
特点 精确度0.05%满刻度 ±1位数 显示范围-19999-99999可任意规划 可直接量測直流4至20mA電流,無需另接輔助電源 尺寸小(24x48x50mm),穩定性高 分离式端子,配线容易 CE 认证 主要規格 辅助电源: None 精确度: 0.05% F.S. ±1 digit(DC) 输入抗阻: approx. 250 ohm with 20mA input 输入电压降: max. DC5V with 20mA input 最大过载能力: < ±50mA 取样时间: 2.5 cycles/sec. 显示值范围: -19999 - 99999 digit adjustable 归零调整范围: -999-999 digit adjustable 最大值调整范围: -999-999 digit adjustable 过载显示: " doFL " or "-doFL" 极性显示: " 一 " for negative readings 显示幕 : Brigh Red LEDs high 8.6mm(.338") 温度系数 : 50ppm/℃ (0-50℃) 参数设定方式: Touch switches 记忆型式: Non-volatile E2 外壳材料: ABS 绝缘耐压能力: 2KVac/1 min. (input/case) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) 外型尺寸: 24x48x50mm CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-10-09
上传用户：lhuqi
特点 精确度0.1%满刻度 ±1位数 显示范围-19999-99999可任意规划 可直接量测直流电流/直流电压,无需另接辅助电源 尺寸小(24x48x50mm),稳定性高 分离式端子,配线容易 CE 认证 2.主要規格 辅助电源: None 精确度: 0.1% F.S. ±1 digit(1-100%F.S.) 输入抗阻 : >100Mohm(<2V range) >2Mohm(<2Vrange) < 0.25VA(current ranges) < 1000Vrms(>54V ranges) 最大过载能力: < 150Vrms(<54V ranges)
上传时间： 2013-10-08
上传用户：tiantwo
