MARVELL 公司的 Integrated 10/100/1000Mbps Energy Efficient Ethernet Transceiver.
上传时间： 2014-12-29
上传用户：18862121743
提出一种实时数字化光纤传输系统,该系统分为发送端和接收端。发送端用A/D转换器将输入的模拟信号数字化,再用FPGA对数据进行处理,并通过光纤传输。同时,FPGA还控制A/D转换器的工作。接收端用串行收发器TLK1501对接收数据进行解码处理,还原有效信号。
上传时间： 2013-11-13
上传用户：阿谭电器工作室
为了实现温室大棚内的温度、湿度和CO2浓度的数据采集，设计了一种超低功耗的无线传感器网络系统，解决了传统监测系统布线复杂、维护困难等问题。分析了无线测量节点所采用微控制器、传感器和无线收发器的工作特点以及功耗，描述了无线节点的结构原理，给出了系统软件的设计方案和通信方法。实测结果表明，所设计的系统硬件结构简单可靠，功耗较小，通信距离较远，达到了大棚环境参数测量的设计要求。
上传时间： 2013-12-31
上传用户：XLHrest
PL2303 是Prolific 公司生产的一种高度集成的RS232-USB 接口转换器，可提供一个RS232 全双工异步串行通信装置与USB 功能接口便利联接的解决方案。该器件内置USB功能控制器、USB 收发器、振荡器和带有全部调制解调器控制信号的UART， 只需外接几只电容就可实现USB 信号与RS232 信号的转换，能够方便嵌入到各种设备.
上传时间： 2014-12-30
上传用户：15527161163
上传时间： 2013-12-24
上传用户：spman
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上传时间： 2013-10-24
上传用户：s蓝莓汁
Abstract: This article describes the Antenna Interface Standards Group (AISG) standard in telecommunications and details itshardware implementation. It explains how a fully integrated transceiver such as the MAX9947 can help reduce space and cost, andsolve bus arbitrations in base-station tower equipment.
上传时间： 2014-12-30
上传用户：wangchong
提出了一种基于PIC16F877A微控制器和CC2500射频收发器芯片的低功耗、低成本RFID（Radio Frequency Identification， 无线射频识别）局域定位系统设计方法，介绍了系统的定位工作原理、主要硬件电路模块及定位算法的设计和实现。采用基于序列号对时隙数运算的排序算法有效解决了多标签识别碰撞的问题，基于射频辐射强度（Received Signal Strength Indication， RSSI）和圆周定位算法实现了基于RFID多标签系统的平面定位。实验测试表明，这种射频定位方法能够实现一定精度下的无线局域定位的功能。
上传时间： 2013-11-06
上传用户：weareno2
上传时间： 2014-12-30
上传用户：zwei41
为满足无线网络技术具有低功耗、节点体积小、网络容量大、网络传输可靠等技术要求，设计了一种以MSP430单片机和CC2420射频收发器组成的无线传感节点。通过分析其节点组成，提出了ZigBee技术中的几种网络拓扑形式，并研究了ZigBee路由算法。针对不同的传输要求形式选用不同的网络拓扑形式可以尽大可能地减少系统成本。同时针对不同网络选用正确的ZigBee路由算法有效地减少了网络能量消耗，提高了系统的可靠性。应用试验表明，采用ZigBee方式通信可以提高传输速率且覆盖范围大，与传统的有线通信方式相比可以节约40%左右的成本。 Abstract: To improve the proposed technical requirements such as low-ower， small nodes， large capacity and reliable network transmission， wireless sensor nodes based on MSP430 MCU and CC2420 RF transceiver were designed. This paper provided network topology of ZigBee technology by analysing the component of the nodes and researched ZigBee routing algorithm. Aiming at different requirements of transmission mode to choose the different network topologies form can most likely reduce the system cost. And aiming at different network to choose the correct ZigBee routing algorithm can effectively reduced the network energy consumption and improved the reliability of the system. Results show that the communication which used ZigBee mode can improve the transmission rate， cover more area and reduce 40% cost compared with traditional wired communications mode.
上传时间： 2013-10-09
上传用户：robter
