代码搜索：定时报警

找到约 10,000 项符合「定时报警」的源代码

代码结果 10,000
热门代码： main.c GPIO I2C SPI UART timer interrupt ADC PWM LED
www.eeworm.com/read/392323/8349641

h main.h

#include "data_type.h" #define TIMER0H 0xf9 //定时0的最大间隔 1000us=1536= 0x6f 0x1f #define TIMER0L 0xff // #define WDT_CONTRVAL 0x3c #define XORSTART 0xff
·
www.eeworm.com/read/369078/9663851

c rfs2bak.c

/*状态特征编码，监控程序在定时中断中*/ #include #include typedef unsigned char unchar; typedef unsigned int unint; sbit LED=P3^4; sbit C=PSW^7; unchar data buf1=0,buf2=0,buf3=0,buf4=0,t
·
www.eeworm.com/read/369078/9663871

c rfs2.c

/*状态特征编码，监控程序在定时中断中*/ #include typedef unsigned char unchar; typedef unsigned int unint; sbit LED=P3^4; unchar data buf1=0,buf2=0,buf3=0,buf4=0,time=0; unchar data keyc=0,nh=0,noq
·
www.eeworm.com/read/172823/9687388

m lorenzeq.m

function xdot = lorenzeq(t,x) %LORENZEQ 本函数用来描述Lorenz方程。 %给定时间变量t和状态变量x, 则由此函数可以求出导数xdot %Designed by Prof D Xue (c) 2000 xdot=[-8/3*x(1)+x(2)*x(3); -10*x(2)+10*x(3); -x(1)*x(2)+
·
www.eeworm.com/read/367777/9733077

c 正常的main.c

//太阳能帽子 AVR驱动程序 2MHZ内部标定时钟 快速定位双PWM 恢复值50 //2007年4月10 //溶丝位 时钟 0010 #include"avr/io.h" #include"avr/iom8.h" #include"avr/signal.h" #include "ad.h" void yanshi(unsigned int x)
·
www.eeworm.com/read/367609/9739944

m lorenzeq.m

function xdot = lorenzeq(t,x) %LORENZEQ 本函数用来描述Lorenz方程。 %给定时间变量t和状态变量x, 则由此函数可以求出导数xdot %Designed by Prof D Xue (c) 2000 xdot=[-8/3*x(1)+x(2)*x(3); -10*x(2)+10*x(3); -x(1)*x(2)+
·
www.eeworm.com/read/414151/11126204

c tr.c

#include #include #include #define uchar unsigned char #define uint unsigned int sbit EXF2=T2CON^6 //主程序 定义中断源，并对定时器赋初值，以及向8253寄存器写控制字 void main(void) { //以下是设置中断
·
www.eeworm.com/read/413142/11165360

c pwm_t2.c

/* File: pwm_t2.c 说明: PWM波形输出,定时器实现 Author:wolfe Data: 2008.10 */ #include "at89x52.h" #include "ES51_II.h" #include "es51_ii_lib.h" // 输出到P1.0,直接观察LED1亮度粗略地判断. sbit PWM_OUT = P
·
www.eeworm.com/read/267370/11180999

c mc.c

//本程序利用定时中断T0产生固定频率为2KHz的脉冲方波信号，通过示波器进行观察// //初始脉宽为高电平3ms,低电平2ms；// //占空比可通过按键循环调整，步进宽度为0.1ms// #include //=========================================================================//
·
www.eeworm.com/read/412777/11183174

asm interrupt.asm

SECOND EQU 30H COUNT EQU 31H ORG 00H LJMP START ORG 0BH ;定时器0中断入口 LJMP INT_T0 START: MOV SECOND,#00H MOV COUNT,#00H MOV DPTR,#TABLE ;段码表首地址 MOV P0,#3FH
·