搜索结果

The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-23 ...

利用TPM2定时器产生一通道语音信号输出，语音数据为PCM格式:PCM的概念脉冲编码调制(Pulse Code Modulation，PCM)是概念上最简单、理论上最完善的编码系统，是最早研制成功、使用最为广泛的编码系统，但也是数据量最大的编码系统。PCM的编码原理比较直观和简单，它的原理框图如图1-1所示。在这个编码框图中，它的输入是模拟 ...

基于单片机的步进电机开环控制系统:通过ATMEL89C51单片机对步进电机进行控制,主要介绍了步进电机控制器、驱动电路和LED显示电路的设计,实现了步进电机的开环控制。在步进电机控制器的设计中,重点阐述了脉冲产生电路以及对速度的控制。该系统具有成本低、控制方便的特点。关键词: 单片机; 步进电机; 开环控制 Abstract: The ...

The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the s ...

The STWD100 watchdog timer circuits are self-contained devices which prevent systemfailures that are caused by certain types of hardware errors (non-responding peripherals,bus contention, etc.) or software errors (bad code jump, code stuck in loop, etc.).The STWD100 watchdog timer has an input, WDI, ...

51单片机驱动步进电机(含电路图和源程序代码） 源程序:stepper.c stepper.hex /* * STEPPER.C * sweeping stepper's rotor cw and cww 400 steps * Copyright (c) 1999 by W.Sirichote */ ＃i nclude c:\mc5151io.h /* include i/o header file */ ＃i nclude c:\mc5151reg.h register unsigned char j,flag1,temp; registe ...

（Portmon is an application that lets you monitor serial and parallel activity on your local system, or any computer on the network that you can reach via TCP/IP.&nb ...

Introduction to Xilinx Packaging Electronic packages are interconnectable housings for semiconductor devices. The major functions of the electronic packages are to provide electrical interconnections between the IC and the board and to efficiently remove heat generated by the device. Feature sizes a ...

针对传统集成电路（ASIC）功能固定、升级困难等缺点，利用FPGA实现了扩频通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核实现NCO模块，在下变频模块调用了硬核乘法器并引入CIC滤波器进行低通滤波，给出了DQPSK解调的原理和实现方法，推导出一种简便的引入?仔/4固定相移的实现方法。采用模块化的设计方法使用VHDL语言 ...

特点 最高輸入頻率 10KHz 显示范围0-9999（一段设定）0至999999累积量 计数速度 50/10000脈波/秒可选择 输入脈波具有预设刻度功能 累积量同步（批量）或非同步（批次）计数可选择 数位化指拨设定操作简易 计数暂时停止功能 1组报警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sin ...