搜索结果

BIT_SELFREFRESH EQU (1<<22) ;定义SDRAM自刷新标志位 16 17 ;Pre-defined constants 预定义6种工作模式 18 USERMODE EQU 0x10 ;用户模式 19 FIQMODE EQU 0x11 ;快速中断模式 20 IRQMODE EQU 0x12 ;中断模式 21 SVCMODE EQU 0x13 ;监管模式 22 ABORTMODE EQU 0x17 ;异常中断模式 23 UNDEFMODE EQU 0x1b ;未定义模 ...

为提高温度测量效率，降低系统的成本，扩展传输距离，设计出一种新型温度采集系统。单片机通过控制具有单总线方式的温度传感器DS18B20实现对温度的测量，同时单片机通过控制具有单总线方式300～450MHz频率范围内的MAX7044与MAX7033无线发射与接收芯片实现温度数据的无线传输。与传统温度采集系统相比，该系统利用单总线方式 ...

介绍了电力操作电源与智能电池巡检系统的特点，给出了一种基于超低功耗单片机MSP430 F149针对中小型变电站自动化运行的专用设备的基本设计原理及实现方法，最后给出了详细硬件构成和软件实现。该系统能满足中小型变电站安全、可靠、自动运行的要求，并通过与上位机的串行通信实现变电站的远程管理和控制。 Abstract: &nb ...

FeaturesThe following standard features are provided.• Choice of RTOS scheduling policy1. Pre-emptive:Always runs the highest available task. Tasks of identical priorityshare CPU time (fully pre-emptive with round robin time slicing).2. Cooperative:Context switches only occur if a task blocks, ...

The Controller Area Network (CAN) is a serial, asynchronous, multi-master communication protocol forconnecting electronic control modules, sensors and actuators in automotive and industrial applications.With the SJA1000, Philips Semiconductors provides a stand-alone CAN controller which is more than ...

文章提出了一种精简指令集8 位单片机中, 算术逻辑单元的工作原理。在此基础上, 对比传统PIC 方案、以及在ALU 内部再次采用流水线作业的332 方案、44 方案, 并用Synopsys 综合工具实现了它们。综合及仿真结果表明, 根据该单片机系统要求, 44 方案速度最高, 比332 方案可提高43.9%, 而面积仅比最小的332 方案增加1.6%。在分析 ...

The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using SW routines implemented in C. The code is focused onthe SAB C513, but will fit to all C500 derivatives.Beyond the low level software drivers a test shell is delivered. This shell a ...

In this document, the term Ô60xÕ is used to denote a 32-bit microprocessor from the PowerPC architecture family that conforms to the bus interface of the PowerPC 601ª, PowerPC 603ª, or PowerPC 604 microprocessors. Note that this does not include the PowerPC 602ª microproc ...

All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, howeve ...

All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, howeve ...