搜索结果

Applying power to a standard logic chip, SRAM, or EPROM, usually results in output pinstracking the applied voltage as it rises. Programmable logic attempts to emulate that behavior,but physics forbids perfect emulation, due to the device programmability. It requires care tospecify the pin behavio ...

Today’s digital systems combine a myriad of chips with different voltage configurations.Designers must interface 2.5V processors with 3.3V memories—both RAM and ROM—as wellas 5V buses and multiple peripheral chips. Each chip has specific power supply needs. CPLDsare ideal for han ...

  The Virtex-4 features, such as the programmable IDELAY and built-in FIFO support, simplifythe bridging of a high-speed, PCI-X core to large amounts of DDR-SDRAM memory. Onechallenge is meeting the PCI-X target initial latency specification. PCI-X Protocol Addendum tothe PCI Local Bus Spec ...

  Xilinx FPGAs require at least two power supplies: VCCINTfor core circuitry and VCCO for I/O interface. For the latestXilinx FPGAs, including Virtex-II Pro, Virtex-II and Spartan-3, a third auxiliary supply, VCCAUX may be needed. Inmost cases, VCCAUX can share a power supply with VCCO.The ...

 波长信号的解调是实现光纤光栅传感网络的关键，基于现有的光纤光栅传感器解调方法，提出一种基于FPGA的双匹配光纤光栅解调方法，此系统是一种高速率、高精度、低成本的解调系统，并且通过引入双匹配光栅有效地克服了双值问题同时扩大了检测范围。分析了光纤光栅的测温原理并给出了该方案软硬件设计，综合考虑系统的解 ...

印刷电路板（PCB）设计解决方案市场和技术领军企业Mentor Graphics（Mentor Graphics）宣布推出HyperLynx® PI（电源完整性）产品，满足业内高端设计者对于高性能电子产品的需求。HyperLynx PI产品不仅提供简单易学、操作便捷，又精确的分析，让团队成员能够设计可行的电源供应系统；同时缩短设计周期，减少原型生成、重 ...

PCB LAYOUT 術語解釋(TERMS)1. COMPONENT SIDE(零件面、正面)︰大多數零件放置之面。2. SOLDER SIDE(焊錫面、反面)。3. SOLDER MASK(止焊膜面)︰通常指Solder Mask Open 之意。4. TOP PAD︰在零件面上所設計之零件腳PAD，不管是否鑽孔、電鍍。5. BOTTOM PAD：在銲錫面上所設計之零件腳PAD，不管是否鑽孔、電鍍。6. POSITIV ...

Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This wor ...

|Introduction􀂄􀂄 Basic Concept􀂄􀂄 Tips to layout Power circuit􀂄􀂄 Type of Power circuit Basic Concept􀂄􀂄 Maximum Current calculation􀂄􀂄 Resistance of Copper􀂄􀂄 ideal power supply & noise􀂄&# ...

Q01、如何使一条走线至两个不同位置零件的距离相同?  您可先在Design/Rule/High Speed/Matched Net Lengths的规则中来新增规则设定,最 后再用Tools/EqualizeNet Lengths 来等长化即可。 　 Q02、在SCHLIB中造一零件其PIN的属性，如何决定是Passive, Input, I/O, Hi- Z, ...