搜索结果
找到约 53 项符合
discussed 的查询结果
按分类筛选
单片机编程 基于C8051F020的触摸屏驱动控制
C8051F020单片机通过SPI接口驱动四线电阻式触摸屏控制器TSC2046，利用中断方式驱动TSC2046设计软件。介绍了触摸屏的工作原理、TSC2046工作方式以及典型应用电路。
Abstract:
 The C8051F020 MCU is connected with the TSC2046 which is a 4-wire touch screen controller. The TSC2046 is controlled by interrup ...
单片机编程 基于MPC555与CS8900A的以太网扩展设计
 
 介绍了MPC555与CS8900A扩展以太网的硬件设计图。以NUCLUES PLUS操作系统为基础，介绍了网卡软件驱动程序的编制，给出了以太网协议包嵌入NUCLEUS PLUS操作系统的实现方法。
Abstract:
 The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program ...
单片机编程 基于ATmgea8单片机的加热控制系统
 介绍基于ATmega8型单片机的温度测量及加热控制系统。分析系统的工作原理，详尽讨论系统的硬件电路和软件流程。实验证明，该系统工作可靠，稳定性高。
Abstract:
 The new temperature measuring and heating control system based on ATmega8 MCU is introduced.The system’s working principles is analyze ...
单片机编程 基于P87C591的信号采集节点的设计
介绍了CAN总线和P87C591单片机的特点，给出了基于P87C591单片机的信号采集节点的软、硬件设计，指出了硬件电路设计中应注意的问题，在软件设计中重点介绍了节点初始化、报文发送和报文接收等子程序。
Abstract:
 The features of CAN Bus and the microcontroller P87C591 are introduced, and the design of hardw ...
单片机编程 PICkit™ 2 Microcontrolle
PICkit™ 2 Microcontroller Programmer USER’S GUIDE
This chapter contains general information that will be useful to know before using thePICkit™ 2 Microcontroller Programmer. Items discussed in this chapter include:• Document Layout• Conventions Used in this Guide• Warr ...
单片机编程 PCA9555 16bit I2C-bus and SMBu
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lo ...
单片机编程 基于P87C591的CAN总线系统智能节点设计
基于P87 C591的CAN总线系统智能节点设计Design of CAN System Intelligent Node Based on P87C591
给出了基于带CAN控制器的单片8位微控制器P87C591的智能节点的硬件电路及软件结构，详细介绍了设计中的难点及实现过程中应注意的问题。关键词:CAN总线;智能节点
Abstract:A h ardc ircuita nds oftw arec onfigurationo fth e ...
单片机编程 基于多点网络的水厂自动监控系统设计
基于多点网络的水厂自动监控系统设计Design of MPI Based Automatic Monitoring and Control System in Water Works刘 美 俊(湖南工程学院，湘潭411101)摘要针对水厂工作水泵多、现场离控制站距离远的特点，提出了一种基于MPI多点网络的自动监控系统的设计方法，分析了系统的工作原理，介绍了系统中数据的采集与处理、主站 ...
DSP编程 基于DSP的车载雷达测速系统设计
针对运行中火车测速运用多普勒效应采用DSP 设计雷达测速系统并阐述了其基本设计思想与工作原理给出系统硬件软件设计结构和原理图改善了原有光电测速精度提高了系统工作稳定性和可靠性经实验证明DSP 采集板工作稳定测速效果好关键词DSP; 雷达测速; 多普勒效应
On Board DSP-Based Radar Speed Measurement System TANG Wei, ...
教程资料 Employing a Single-Chip Transceiver in Femtocell Base-Station Applications
Abstract: This application note discusses the development and deployment of 3G cellular femtocell base stations. The technicalchallenges for last-mile residential connectivity and adding system capacity in dense urban environments are discussed, with 3Gfemtocell base stations as a cost-effective s ...