搜索结果
找到约 74 项符合
Toggle 的查询结果
按分类筛选
书籍源码 MSP-FET430P410 Demo - Timer_A Toggle P5.1, CCR0 Contmode ISR, DCO SMCLK Description Toggle P5.1 u
MSP-FET430P410 Demo - Timer_A Toggle P5.1, CCR0 Contmode ISR, DCO SMCLK
Description Toggle P5.1 using using software and TA_0 ISR. Toggle rate is
set at 50000 DCO/SMCLK cycles. Default DCO frequency used for TACLK.
Durring the TA_0 ISR P5.1 is toggled and 50000 clock cycles are added to CCR0. TA_ ...
单片机编程 CAT28LV64-64Kb CMOS并行EEPROM数据手
The CAT28LV64 is a low voltage, low power, CMOS Parallel EEPROM organized as 8K x 8−bits. It requires a simple interface for in−system programming. On−chip address and data latches, self−timed write cycle with auto−clear and VCC power up/down write protection eliminate ...
单片机编程 EZ-USB FX系列单片机USB外围设备设计与应用
EZ-USB FX系列单片机USB外围设备设计与应用:PART 1 USB的基本概念第1章 USB的基本特性1.1 USB简介21.2 USB的发展历程31.2.1 USB 1.131.2.2 USB 2.041.2.3 USB与IEEE 1394的比较41.3 USB基本架构与总线架构61.4 USB的总线结构81.5 USB数据流的模式与管线的概念91.6 USB硬件规范101.6.1 USB的硬件特性111.6.2 USB接口的电气特 ...
DSP编程 VDSP++打开。This directory contains an example ADSP-BF537 RTC project that does a basic blink routine a
VDSP++打开。This directory contains an example ADSP-BF537 RTC project that does a basic blink routine and
then puts the part in deep sleep mode to be woken up from a RTC Stopwatch Event. Once woken up,
the RTC is reconfigured to toggle the EZ KIT LEDs using RTC second, minute, hour, and day interrup ...
单片机开发 富士通单片机MB902420系列 extINT Project: All external Interrupt-Pins INT0 .. INT7 will be enabled. A fall
富士通单片机MB902420系列
extINT Project:
All external Interrupt-Pins INT0 .. INT7 will be enabled.
A falling edge on INTx will toggle PDR4_P4x
in order to toggle the LEDx of the Flash-CAN-100P Board
e.g. falling edge on INT3 will result in LED D3 will toggleP47..P40 (UserLEDs of FlashCan100P)
and ...
微处理器开发 Name Function --- --- --- --- --- --- Check_SST_39VF160 Check manufacturer and device ID CFI_Que
Name Function
--- --- --- --- --- ---
Check_SST_39VF160 Check manufacturer and device ID
CFI_Query CFI Query Entry/Exit command sequence
Erase_Entire_Chip Erase the contents of the entire chip
Erase_One_Sector Erase a sector of 2048 word
Erase_One_Block Erase a block of 32K word
Program_One_Word Al ...
单片机开发 本例展示了如何利用外设TIM2来产生四路频率不同的信号。 TIM2时钟设置为36MHz
本例展示了如何利用外设TIM2来产生四路频率不同的信号。
TIM2时钟设置为36MHz，预分频设置为2，使用输出比较-翻转模式（Output Compare Toggle Mode）。
TIM2计数器时钟可表达为：TIM2 counter clock = TIMxCLK / (Prescaler +1) = 12 MHz
设置TIM2_CCR1寄存器值为32768，则CC1更新频率为TIM2计数器时钟频率除以CCR1寄存 ...
DSP编程 程序所在目录：ex6_AD 板上引出的两路A/D 转换对应DSP 的A/D 模块分别是通道0 和通道8
程序所在目录：ex6_AD
板上引出的两路A/D 转换对应DSP 的A/D 模块分别是通道0 和通道8，输入电压0-5V 。
本开发板使用DA 的输出作为AD 的输入，因此需将5J2 的1-2，3-4 分别用短路子短接。
打开CC2000,进行如下操作：
1．Project->Open ，打开该目录中的工程文件。
2．Project->Rebuild ALL,编译链接
3．File->Lo ...
DSP编程 程序所在目录：ex7_CAN 由于调试CAN总线通讯需要外部的CAN设备。所以在没有外部CAN设备的情况下
程序所在目录：ex7_CAN
由于调试CAN总线通讯需要外部的CAN设备。所以在没有外部CAN设备的情况下，本样例程序中采用了CAN的自测试模式通信，即使用CANBOX4发送CANBOX0接收。在定时器中断服务程序中执行发送；中断方式接收CAN信息。
打开CC2000,进行如下操作：
1. Project->Open ，打开该目录中的工程文件。
2. Project ...
VHDL/FPGA/Verilog This tutorial explains how to communicate with IO devices on the DE2 Board and how to deal with inte
This tutorial explains how to communicate with IO devices on the DE2 Board and how to deal with interrupts using C and the Altera Monitor Program. Two example programs are given that diplay the state of the toggle switches on the red LEDs. The &#64257 rst program uses the programmed I/O approach a ...