搜索结果

  The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) ...

  In an increasing trend, telecommunications, networking,audio and instrumentation require low noise power supplies.In particular, there is interest in low noise, lowdropout linear regulators (LDO). These components powernoise-sensitive circuitry, circuitry that contains noisesensitiveeleme ...

Demonstration circuit 1562A is an engineering toolto design and evaluate the LTC699X-X family ofTimerBlox circuits. The center section of the boardcontains a pre-configured TimerBlox function.DC1562A comes in twelve timing function variationsas outlined in Table 1.Surrounding the center board is a ...

附件下载proteus7.8破解版包含了Proteus中文入门教程在内 Proteus Pro 7.8 sp2 汉化破解版，该Proteus 汉化破解版解决了7.2版本运行10分钟就自动关闭的问题，是目前最Protus中最高的版本。Proteus 不仅具有其它EDA工具软件的仿真功能，还能仿真单片机及外围器件，它是目前最好的仿真单片机及外围器件的工具。从原理图 ...

介绍基于ISA总线与KH-9300的数据采集板卡的设置，详细说明8254定时计数器及8259中断控制器的结构特点、工作方式、控制字等，探讨中断类型、中断处理程序、中断矢量表及其填写。重点讲述使用TorboC编写中断服务程序的方法，应注意的主要问题及程序测试的结果。 Abstract:  The settings of KH-9300 data acquisition ...

   介绍了MPC555与CS8900A扩展以太网的硬件设计图。以NUCLUES PLUS操作系统为基础，介绍了网卡软件驱动程序的编制，给出了以太网协议包嵌入NUCLEUS PLUS操作系统的实现方法。 Abstract:  The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program ...

普通查表原理 查表时，执行CALL指令后，下一条指令的地址被自动压入堆栈中，然后跳转到数据表处，执行TJMP指令，PC指针跳转到PC11~PC8,TBR（TABLE BRANCH REGISTER）,AC(累加器)所指向的地址，该地址的数据通过RTNW指令返回，其中，高4位数据保存到TBR寄存器中，低4位数据保存到累加器AC中。返回时PC指针会自动被堆栈中保存 ...

FEATURES400 MSPS internal clock speedIntegrated 10-bit DAC32-bit tuning wordPhase noise ≤ –120 dBc/Hz @ 1 kHz offset (DAC output)Excellent dynamic performance>75 dB SFDR @ 160 MHz (±100 kHz offset) AOUTSerial I/O control1.8 V power supplySoftware and hardware controlled power-down48-lead TQFP/EP ...

Proteus中文入门基础教程 目  录 第一章  概述... 2 一、进入Proteus ISIS. 2 二、工作界面... 3 三、基本操作... 3 图形编辑窗口... 3 预览窗口（The Overview Window）... 4 对象选择器窗口... 5 图形编辑的基本操作... 5 参考1. 10 参考2作原理图仿真调试... 12 四、实例一... 16 电路图的绘制... 17 KeilC与P ...

Using the XGATE for Manchester DecodingTable of Contents 1 Introduction                         1.1 XGATE Module in S12X           ...