搜索结果

本程序运行于C8051F330，功能为接收遥控器发出的红外信号，然后等待上位机通过I2C总线来读取。IR数据接收完毕后，不再采集新的IR数据，一直等待上位机将数据取走后才开始准备接收新的IR数据

DA 转换 产生三角波 正旋波 梯形波（dac0832)换电路接成同相电压输出形式，其输出电压Vout=IR(1+R2/R1)。

L为桩长，r为计算点与桩轴线的水平距离，z为计算点距离地面深度。都取正值 ％f1,f2,f3依次是点荷载、均布荷载以及三角形荷载下的Geddes应力解函数 ％Ip,Ir,It依次是对应三个荷载下的应力系数，负表示拉，正表示压

Carrier-phase synchronization can be approached in a general manner by estimating the multiplicative distortion (MD) to which a baseband received signal in an RF or coherent optical transmission system is subjected. This paper presents a unified modeling and estimation of the MD in finite-alphabet d ...

In this paper, a new family of Cassinian wave-guides is proposed, simulating and calculation are finished with CST Microwave Studio that based on Finite Integral Technique (FIT), and some results are given. Electromagnetic field mode type of it is TE, electromagnetic field is stronger near neck regi ...

UCS (Ultra Corba Simulator) is one more powerful corba client/servant simulator tool than other similar products(e.g. Telcopro s MtSim, or OpenFusion s Corba Explorer, or eaiBridge s CAST). It doesn t need idl-related helper class or IR service.

A new cable fault location method based on wavelet reconstruction is proposed. In this method the difference between the currents of faulty phase and sound phase under the high voltage pulse excitation is used as the measured signal and is decomposed in multi-scale by wavelet transform, then reconst ...

C++编码规范,摩托罗拉公司， 这本书最主要的思想来源是摩托罗拉公司st眺H聊kes和M皿Pebx为寻呼系统部 所写的6MlJ6[IR‘‘／of Zf6‘小‘C??，其次是ScoK MeyeK的两本著作坝“5v‘Ct?和 他用ZJF6cfIv‘C?十，另外，也参考了SW公RJ的Ct十比‘fb GM5d6(P6阳DW6JoP6f 6 yF8朋d62J、EnchG朋皿a等的(4设L1模式——可复用面向对象 ...

Application Note Abstract This Application Note introduces a complete and detailed PSoC&reg project. Telephone Call Logger keeps the detailed record of approximately 945 phone calls (7-digit number is assumed to be one phone call) including date, start time and the duration of the phone call in the ...

rt12864m样例程序，管脚号 管脚名称 电平 管脚功能描述 1 VSS 0V 电源地 2 VCC +5V 电源正 3 V0 - 对比度（亮度）调整 4 RS(CS） H/L RS="H",表示DB7--DB0为显示数据 4 RS(CS） H/L RS="L",表示DB7--DB0为显示指令数据 5 R/W(SID) H/L R/W="H",E="H",数据被读到DB7--DB0 5 R/W(SID) H/L R/W="L",E="H→L", DB7--DB0的数据 ...