搜索结果
找到约 68 项符合
Heavy-duty 的查询结果
J2ME 超精典手机版Call of Duty(使命的召唤)
超精典手机版Call of Duty(使命的召唤)，可以研究一下。
系统设计方案 design of boost converter using mtalab simulink duty ratio=0.5833 used in this file
design of boost converter using mtalab simulink
duty ratio=0.5833 used in this file
电源技术 100-15V TO 12V DCDC 原理图 PCB BOM表
高的工作电压高达100V N双N沟道MOSFET同步驱动 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture t ...
电源技术 DN457宽输入电压范围同步降压稳压器
 
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) ...
电源技术 两相同步降压型控制器具有轻负载逐级递减模式
 
Today’s computer, datacom, and telecom systems demandpower supplies that are effi cient, respond quicklyto load transients and accurately regulate the voltageat the load. For example, load current can be measuredby using the inductor DCR, thus eliminating the needfor a dedicated sen ...
电源技术 飞利浦绿色电源集成电路选型资料
IC 特色 :
˙ 半谐振模式之 ZVS零电压切换 , 能有效降低切换损失 , 提高效率 , 并具展频功能 , 改善EMI .
˙ 轻 / 重载的 Duty Factor 皆在 CCM 与 DCM 边缘 , 是最能发挥次级 "同步整流" 效率的一种工作模式 .
˙ 空载时进入 Cycle Skipping ( Typical 0.3W ) , 有效达成环保规範 .
˙ 内建 "LEB前缘 ...
单片机编程 基于ATmega48单片机的可调交流电子负载的设计
介绍一种无极可调交流电子负载设计的新方法，由ATmega48单片机输出PWM波，通过上位机设定不同的占空比控制场效应管的通断时间，即改变流过场效应管的平均电流。根据电流的大小，可以等效为相应的负载，并将采集的电流值显示在上位机上。文中对该系统的软﹑硬件设计思路作了详细的分析，阐述了其设计原理。
 
Abstract ...
测试测量 基于Multisim 10的矩形波信号发生器仿真与实现
在Multisim 10软件环境下，设计一种由运算放大器构成的精确可控矩形波信号发生器，结合系统电路原理图重点阐述了各参数指标的实现与测试方法。通过改变RC电路的电容充、放电路径和时间常数实现了占空比和频率的调节，通过多路开关投入不同数值的电容实现了频段的调节，通过电压取样和同相放大电路实现了输出电压幅值的调节 ...
压缩解压 aPLib is a 32-bit compression library based on the compression algorithm used in aPACK (my executa
aPLib is a 32-bit compression library based on the compression algorithm
used in aPACK (my executable packer). aPLib is an easy-to-use alternative
to many of the heavy-weight compression libraries available.
其他嵌入式/单片机内容 he LPC932 can be used to create a Pulse Width Modulated PWM signal. That s an analog signal, with on
he LPC932 can be used to create a Pulse Width Modulated PWM signal. That s an analog signal, with only 2 discrete levels, for example 0V and 5V and a constant period. The current value of this signal at a certain poiTnt of time is proportional to its Duty Cycle. That s the High Time during one perio ...