搜索结果

该系统由单片机89S52控制模块，程控宽带放大模块，整形模块，FPGA内频率、相位差测量模块等构成，采用等精度测频法测出频率和周期，可测量有效值为0.01～5V，频率范围1Hz～20MHz信号的频率、周期信号，精度高达10-6。采用计数法测量相位差，该系统可测量有效值0.5～5V，频率10Hz～100kHz信号的相位差，精度为1°。系统功能 ...

描述 P89C660/662/664/668单片机内带6KB/32KB/64KB/64KBFlash存储器,该存储器既可并行编程也可以串行在系统编程(ISP).在实际的成型产品中,可通过ISP升级用户程序在BootROM程序. 在Boot ROM程序中,可通过一个默认的串行下载器(UART)对Flash存储器作ISP编程,而在Flash代码区中并不需要有调用下载器的代码,用户程序可通过调用 ...

基于幅移键控技术ASK（Amplitude-Shift Keying），以C8051F340单片机作为监测终端控制器，C8051F330D单片机作为探测节点控制器，采用半双工的通信方式，通过监控终端和探测节点的无线收发电路，实现数据的双向无线传输。收发电路采用直径为0.8 mm的漆包线自行绕制成圆形空心线圈天线，天线直径为（3.4±0.3）cm。试验表明， ...

The PCF8578 is a low power CMOS1 LCD row and column driver, designed to drive dotmatrix graphic displays at multiplex rates of 1:8, 1:16, 1:24 or 1:32. The device has40 outputs, of which 24 are programmable and configurable for the following ratios ofrows/columns: 32¤8, 24¤16, 16¤24 or 8¤32. The ...

1 FEATURES· Single chip LCD controller/driver· 1 or 2-line display of up to 24 characters per line, or2 or 4 lines of up to 12 characters per line· 5 ′ 7 character format plus cursor; 5 ′ 8 for kana(Japanese syllabary) and user defined symbols· On-chip:– generation of LCD supply voltage (exte ...

The CAT93C46 is a 1 kb Serial EEPROM memory device which isconfigured as either 64 registers of 16 bits (ORG pin at VCC) or 128registers of 8 bits (ORG pin at GND). Each register can be written (orread) serially by using the DI (or DO) pin. The CAT93C46 features aself−timed internal write with ...

描述P89C660/662/664/668单片机内带6KB/32KB/64KB/64KB Flash存储器,该存储器既可并行编程也可以串行在系统编程(ISP).在实际的成型产品中,可通过ISP升级用户程序. 在Boot ROM程序中可通过一个默认的串行下载器(UART)对Flash存储器作ISP编程,而在Flash代码区中并不需要有调用下载器的代码,用户程序可通过调用在Boot ROM中的 ...

The bootloader is stored in the internal boot ROM memory (system memory) of STM32devices. It is programmed by ST during production. Its main task is to download theapplication program to the internal Flash memory through one of the available serialperipherals (USART, CAN, USB, etc.). A communication ...

The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to ...

PICKIT™ 2 PROGRAMMER-TO-GO USER GUIDE The PICkit 2 Programmer-To-Go functionality allows a PIC MCU memory image to be downloaded into the PICkit 2 unit for later programming into a specific PIC MCU. No software or PC is required to program devices once the PICkit 2 unit is set up for Programmi ...