stm32f10x.h

中文固件库.rar

/**
  ******************************************************************************
  * @file stm32f10x.h
  * @brief CMSIS Cortex-M3 Device Peripheral Access Layer Header File. 
  *        This file contains all the peripheral register's definitions, bits 
  *        definitions and memory mapping for STM32F10x High Density, Medium 
  *        Density and Low Density devices.
  * @author STMicroelectronics - MCD Application Team
  * @version V3.0.0
  * @date 04/06/2009
  ******************************************************************************
  *
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
  *
  * <h2><center>&copy; COPYRIGHT 2009 STMicroelectronics</center></h2>
  ******************************************************************************
  */

/** @addtogroup CMSIS
  * @{
  */

/** @addtogroup stm32f10x
  * @{
  */
    
#ifndef __STM32F10x_H
#define __STM32F10x_H
  
/** @addtogroup Library_configuration_section
  * @{
  */
  
/* Uncomment the line below according to the target STM32 device used in your
   application 
  */

#if !defined (STM32F10X_LD) && !defined (STM32F10X_MD) && !defined (STM32F10X_HD)
  /* #define STM32F10X_LD */   /*!< STM32 Low density devices */
  /* #define STM32F10X_MD */   /*!< STM32 Medium density devices */
  #define STM32F10X_HD   /*!< STM32 High density devices */
#endif
/*  Tip: To avoid modifying this file each time you need to switch between these
        devices, you can define the device in your toolchain compiler preprocessor.

 - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx microcontrollers
   where the Flash memory density ranges between 16 and 32 Kbytes.
 - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx microcontrollers
   where the Flash memory density ranges between 64 and 128 Kbytes.
 - High-density devices are STM32F101xx and STM32F103xx microcontrollers where
   the Flash memory density ranges between 256 and 512 Kbytes.
  */

#if !defined  USE_STDPERIPH_DRIVER
/**
 * @brief Comment the line below if you will not use the peripherals drivers.
   In this case, these drivers will not be included and the application code will 
   be based on direct access to peripherals registers 
   */
  /*#define USE_STDPERIPH_DRIVER*/
#endif

/**
 * @brief In the following line adjust the value of External High Speed oscillator (HSE)
   used in your application 
   */
#define HSE_Value    ((uint32_t)8000000) /*!< Value of the External oscillator in Hz*/
/**
 * @brief In the following line adjust the External High Speed oscillator (HSE) Startup 
   Timeout value 
   */
#define HSEStartUp_TimeOut   ((uint16_t)0x0500) /*!< Time out for HSE start up */

#define HSI_Value    ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/


/*!< [31:16] STM32F10x Standard Peripheral Library main version */
#define __STM32F10X_STDPERIPH_VERSION_MAIN   (0x03)                                  
/*!< [15:8]  STM32F10x Standard Peripheral Library sub1 version */
#define __STM32F10X_STDPERIPH_VERSION_SUB1   (0x00)
/*!< [7:0]  STM32F10x Standard Peripheral Library sub2 version */
#define __STM32F10X_STDPERIPH_VERSION_SUB2   (0x00) 
/*!< STM32F10x Standard Peripheral Library version number */
#define __STM32F10X_STDPERIPH_VERSION       ((__STM32F10X_STDPERIPH_VERSION_MAIN << 16)\
                                             | (__STM32F10X_STDPERIPH_VERSION_SUB1 << 8)\
                                             | __STM32F10X_STDPERIPH_VERSION_SUB2)

/**
  * @}
  */

/** @addtogroup Configuration_section_for_CMSIS
  * @{
  */

/**
 * @brief Configuration of the Cortex-M3 Processor and Core Peripherals 
 */
#define __MPU_PRESENT             0 /*!< STM32 does not provide a MPU present or not  */
#define __NVIC_PRIO_BITS          4 /*!< STM32 uses 4 Bits for the Priority Levels    */
#define __Vendor_SysTickConfig    0 /*!< Set to 1 if different SysTick Config is used */

/*!< Interrupt Number Definition */
typedef enum IRQn
{
/******  Cortex-M3 Processor Exceptions Numbers ***************************************************/
  NonMaskableInt_IRQn         = -14,    /*!< 2 Non Maskable Interrupt                             */
  MemoryManagement_IRQn       = -12,    /*!< 4 Cortex-M3 Memory Management Interrupt              */
  BusFault_IRQn               = -11,    /*!< 5 Cortex-M3 Bus Fault Interrupt                      */
  UsageFault_IRQn             = -10,    /*!< 6 Cortex-M3 Usage Fault Interrupt                    */
  SVCall_IRQn                 = -5,     /*!< 11 Cortex-M3 SV Call Interrupt                       */
  DebugMonitor_IRQn           = -4,     /*!< 12 Cortex-M3 Debug Monitor Interrupt                 */
  PendSV_IRQn                 = -2,     /*!< 14 Cortex-M3 Pend SV Interrupt                       */
  SysTick_IRQn                = -1,     /*!< 15 Cortex-M3 System Tick Interrupt                   */

/******  STM32 specific Interrupt Numbers *********************************************************/
  WWDG_IRQn                   = 0,      /*!< Window WatchDog Interrupt                            */
  PVD_IRQn                    = 1,      /*!< PVD through EXTI Line detection Interrupt            */
  TAMPER_IRQn                 = 2,      /*!< Tamper Interrupt                                     */
  RTC_IRQn                    = 3,      /*!< RTC global Interrupt                                 */
  FLASH_IRQn                  = 4,      /*!< FLASH global Interrupt                               */
  RCC_IRQn                    = 5,      /*!< RCC global Interrupt                                 */
  EXTI0_IRQn                  = 6,      /*!< EXTI Line0 Interrupt                                 */
  EXTI1_IRQn                  = 7,      /*!< EXTI Line1 Interrupt                                 */
  EXTI2_IRQn                  = 8,      /*!< EXTI Line2 Interrupt                                 */
  EXTI3_IRQn                  = 9,      /*!< EXTI Line3 Interrupt                                 */
  EXTI4_IRQn                  = 10,     /*!< EXTI Line4 Interrupt                                 */
  DMA1_Channel1_IRQn          = 11,     /*!< DMA1 Channel 1 global Interrupt                      */
  DMA1_Channel2_IRQn          = 12,     /*!< DMA1 Channel 2 global Interrupt                      */
  DMA1_Channel3_IRQn          = 13,     /*!< DMA1 Channel 3 global Interrupt                      */
  DMA1_Channel4_IRQn          = 14,     /*!< DMA1 Channel 4 global Interrupt                      */
  DMA1_Channel5_IRQn          = 15,     /*!< DMA1 Channel 5 global Interrupt                      */
  DMA1_Channel6_IRQn          = 16,     /*!< DMA1 Channel 6 global Interrupt                      */
  DMA1_Channel7_IRQn          = 17,     /*!< DMA1 Channel 7 global Interrupt                      */
  ADC1_2_IRQn                 = 18,     /*!< ADC1 et ADC2 global Interrupt                        */
  USB_HP_CAN1_TX_IRQn         = 19,     /*!< USB High Priority or CAN1 TX Interrupts              */
  USB_LP_CAN1_RX0_IRQn        = 20,     /*!< USB Low Priority or CAN1 RX0 Interrupts              */
  CAN1_RX1_IRQn               = 21,     /*!< CAN1 RX1 Interrupt                                   */
  CAN1_SCE_IRQn               = 22,     /*!< CAN1 SCE Interrupt                                   */
  EXTI9_5_IRQn                = 23,     /*!< External Line[9:5] Interrupts                        */
  TIM1_BRK_IRQn               = 24,     /*!< TIM1 Break Interrupt                                 */
  TIM1_UP_IRQn                = 25,     /*!< TIM1 Update Interrupt                                */
  TIM1_TRG_COM_IRQn           = 26,     /*!< TIM1 Trigger and Commutation Interrupt               */
  TIM1_CC_IRQn                = 27,     /*!< TIM1 Capture Compare Interrupt                       */
  TIM2_IRQn                   = 28,     /*!< TIM2 global Interrupt                                */
  TIM3_IRQn                   = 29,     /*!< TIM3 global Interrupt                                */
#ifndef STM32F10X_LD
  TIM4_IRQn                   = 30,     /*!< TIM4 global Interrupt                                */
#endif  
  I2C1_EV_IRQn                = 31,     /*!< I2C1 Event Interrupt                                 */
  I2C1_ER_IRQn                = 32,     /*!< I2C1 Error Interrupt                                 */
#ifndef STM32F10X_LD
  I2C2_EV_IRQn                = 33,     /*!< I2C2 Event Interrupt                                 */
  I2C2_ER_IRQn                = 34,     /*!< I2C2 Error Interrupt                                 */
#endif  
  SPI1_IRQn                   = 35,     /*!< SPI1 global Interrupt                                */
  SPI2_IRQn                   = 36,     /*!< SPI2 global Interrupt                                */
  USART1_IRQn                 = 37,     /*!< USART1 global Interrupt                              */
  USART2_IRQn                 = 38,     /*!< USART2 global Interrupt                              */
#ifndef STM32F10X_LD  
  USART3_IRQn                 = 39,     /*!< USART3 global Interrupt                              */
#endif  
  EXTI15_10_IRQn              = 40,     /*!< External Line[15:10] Interrupts                      */
  RTCAlarm_IRQn               = 41,     /*!< RTC Alarm through EXTI Line Interrupt                */
  USBWakeUp_IRQn              = 42,     /*!< USB WakeUp from suspend through EXTI Line Interrupt  */
#ifdef STM32F10X_HD
  TIM8_BRK_IRQn               = 43,     /*!< TIM8 Break Interrupt                                 */
  TIM8_UP_IRQn                = 44,     /*!< TIM8 Update Interrupt                                */
  TIM8_TRG_COM_IRQn           = 45,     /*!< TIM8 Trigger and Commutation Interrupt               */
  TIM8_CC_IRQn                = 46,     /*!< TIM8 Capture Compare Interrupt                       */
  ADC3_IRQn                   = 47,     /*!< ADC3 global Interrupt                                */
  FSMC_IRQn                   = 48,     /*!< FSMC global Interrupt                                */
  SDIO_IRQn                   = 49,     /*!< SDIO global Interrupt                                */
  TIM5_IRQn                   = 50,     /*!< TIM5 global Interrupt                                */
  SPI3_IRQn                   = 51,     /*!< SPI3 global Interrupt                                */
  UART4_IRQn                  = 52,     /*!< UART4 global Interrupt                               */
  UART5_IRQn                  = 53,     /*!< UART5 global Interrupt                               */
  TIM6_IRQn                   = 54,     /*!< TIM6 global Interrupt                                */
  TIM7_IRQn                   = 55,     /*!< TIM7 global Interrupt                                */
  DMA2_Channel1_IRQn          = 56,     /*!< DMA2 Channel 1 global Interrupt                      */
  DMA2_Channel2_IRQn          = 57,     /*!< DMA2 Channel 2 global Interrupt                      */
  DMA2_Channel3_IRQn          = 58,     /*!< DMA2 Channel 3 global Interrupt                      */
  DMA2_Channel4_5_IRQn        = 59      /*!< DMA2 Channel 4 and Channel 5 global Interrupt        */
#endif
} IRQn_Type;

/**
  * @}
  */

#include "core_cm3.h"
#include "system_stm32f10x.h"
#include <stdint.h>

/** @addtogroup Exported_types
  * @{
  */  

/*!< STM32F10x Standard Peripheral Library old types (maintained for legacy prupose) */
typedef int32_t  s32;
typedef int16_t s16;
typedef int8_t  s8;

typedef const int32_t sc32;  /*!< Read Only */
typedef const int16_t sc16;  /*!< Read Only */
typedef const int8_t sc8;   /*!< Read Only */

typedef __IO int32_t  vs32;
typedef __IO int16_t  vs16;
typedef __IO int8_t   vs8;

typedef __I int32_t vsc32;  /*!< Read Only */
typedef __I int16_t vsc16;  /*!< Read Only */
typedef __I int8_t vsc8;   /*!< Read Only */

typedef uint32_t  u32;
typedef uint16_t u16;
typedef uint8_t  u8;

typedef const uint32_t uc32;  /*!< Read Only */
typedef const uint16_t uc16;  /*!< Read Only */
typedef const uint8_t uc8;   /*!< Read Only */

typedef __IO uint32_t  vu32;
typedef __IO uint16_t vu16;
typedef __IO uint8_t  vu8;

typedef __I uint32_t vuc32;  /*!< Read Only */
typedef __I uint16_t vuc16;  /*!< Read Only */
typedef __I uint8_t vuc8;   /*!< Read Only */

typedef enum {FALSE = 0, TRUE = !FALSE} bool;

typedef enum {RESET = 0, SET = !RESET} FlagStatus, ITStatus;

typedef enum {DISABLE = 0, ENABLE = !DISABLE} FunctionalState;
#define IS_FUNCTIONAL_STATE(STATE) (((STATE) == DISABLE) || ((STATE) == ENABLE))

typedef enum {ERROR = 0, SUCCESS = !ERROR} ErrorStatus;

/**
  * @}
  */

/** @addtogroup Peripheral_registers_structures
  * @{
  */   

/** 
  * @brief Analog to Digital Converter  
  */

typedef struct
{
  __IO uint32_t SR;
  __IO uint32_t CR1;
  __IO uint32_t CR2;
  __IO uint32_t SMPR1;
  __IO uint32_t SMPR2;
  __IO uint32_t JOFR1;
  __IO uint32_t JOFR2;
  __IO uint32_t JOFR3;
  __IO uint32_t JOFR4;
  __IO uint32_t HTR;
  __IO uint32_t LTR;
  __IO uint32_t SQR1;
  __IO uint32_t SQR2;
  __IO uint32_t SQR3;
  __IO uint32_t JSQR;
  __IO uint32_t JDR1;
  __IO uint32_t JDR2;
  __IO uint32_t JDR3;
  __IO uint32_t JDR4;
  __IO uint32_t DR;
} ADC_TypeDef;

/** 
  * @brief Backup Registers  
  */

typedef struct
{
  uint32_t  RESERVED0;
  __IO uint16_t DR1;
  uint16_t  RESERVED1;
  __IO uint16_t DR2;
  uint16_t  RESERVED2;
  __IO uint16_t DR3;