main_ezlink.c

Si4432-T-B1版本资料.rar

			/*CRC Error interrupt occured*/
			if( (ItStatus1 & 0x01) == 0x01 )
			{
				//reset the RX FIFO
       	   SpiWriteRegister(0x08, 0x02);												//write 0x02 to the Operating Function Control 2 register
        	   SpiWriteRegister(0x08, 0x00);												//write 0x00 to the Operating Function Control 2 register
				//blink all LEDs to show the error
				TX_LED = 1;
				RX_LED = 1;
				for(delay = 0; delay < 10000;delay++);
				TX_LED = 0;
				RX_LED = 0;
			}

			/*packet received interrupt occured*/
			if( (ItStatus1 & 0x02) == 0x02 )
			{
 				//Read the length of the received payload
				length = SpiReadRegister(0x4B);											//read the Received Packet Length register
				//check whether the received payload is not longer than the allocated buffer in the MCU
				if(length < 11)
				{
					//Get the reeived payload from the RX FIFO
					for(temp8=0;temp8 < length;temp8++)
					{
						payload[temp8] = SpiReadRegister(0x7F);						//read the FIFO Access register
					}
			
					//check whether the acknowledgement packet received
					if( length == 4 ) 
	            {
	            	if( memcmp(&payload[0], "ACK", 3) == 0 )
					   {
	                 	//blink LED2 to show that ACK received
	     					RX_LED = 1;
							for(delay = 0; delay < 10000;delay++);
	  		   			RX_LED = 0;
						}
					}

					//check whether an expected packet received, this should be acknowledged
					if( length == 8 ) 
	            {
	            	if( memcmp(&payload[0], "BUTTON1", 7) == 0 )
					   {
	               	//blink LED2 to show that the packet received
	     					RX_LED = 1;
							for(delay = 0; delay < 10000;delay++);
	  		   			RX_LED = 0;

							/*send back an acknowledgement*/
							//turn on LED1 to show packet transmission
							TX_LED = 1; 				
							/*set packet content*/
							//set the length of the payload to 4bytes	
							SpiWriteRegister(0x3E, 4);										//write 4 to the Transmit Packet Length register		
							//fill the payload into the transmit FIFO
							SpiWriteRegister(0x7F, 0x41);									//write 0x41 ('A') to the FIFO Access register	
							SpiWriteRegister(0x7F, 0x43);									//write 0x43 ('C') to the FIFO Access register	
							SpiWriteRegister(0x7F, 0x4B);									//write 0x4B ('K') to the FIFO Access register	
							SpiWriteRegister(0x7F, 0x0D);									//write 0x0D (CR) to the FIFO Access register	

							//Disable all other interrupts and enable the packet sent interrupt only.
							//This will be used for indicating the successfull packet transmission for the MCU
							SpiWriteRegister(0x05, 0x04);									//write 0x04 to the Interrupt Enable 1 register	
							SpiWriteRegister(0x06, 0x00);									//write 0x00 to the Interrupt Enable 2 register	
							//Read interrupt status regsiters. It clear all pending interrupts and the nIRQ pin goes back to high.
							ItStatus1 = SpiReadRegister(0x03);							//read the Interrupt Status1 register
							ItStatus2 = SpiReadRegister(0x04);							//read the Interrupt Status2 register

							/*enable transmitter*/
							//The radio forms the packet and send it automatically.
							SpiWriteRegister(0x07, 0x09);									//write 0x09 to the Operating Function Control 1 register

							/*wait for the packet sent interrupt*/
							//The MCU just needs to wait for the 'ipksent' interrupt.
							while(NIRQ == 1);
							//read interrupt status registers to release the interrupt flags
							ItStatus1 = SpiReadRegister(0x03);							//read the Interrupt Status1 register
							ItStatus2 = SpiReadRegister(0x04);							//read the Interrupt Status2 register

							//wait a bit for showing the LED a bit longer
							for(delay = 0; delay < 10000;delay++);
							//turn off the LED
							TX_LED = 0; 	

							//after packet transmission set the interrupt enable bits according receiving mode
							//Enable two interrupts: 
							// a) one which shows that a valid packet received: 'ipkval'
							// b) second shows if the packet received with incorrect CRC: 'icrcerror' 
							SpiWriteRegister(0x05, 0x03); 								//write 0x03 to the Interrupt Enable 1 register
							SpiWriteRegister(0x06, 0x00); 								//write 0x00 to the Interrupt Enable 2 register
							//read interrupt status registers to release all pending interrupts
							ItStatus1 = SpiReadRegister(0x03);							//read the Interrupt Status1 register
							ItStatus2 = SpiReadRegister(0x04);							//read the Interrupt Status2 register
						}
					}
				}
       	}
			//reset the RX FIFO
       	SpiWriteRegister(0x08, 0x02);													//write 0x02 to the Operating Function Control 2 register
        	SpiWriteRegister(0x08, 0x00);													//write 0x00 to the Operating Function Control 2 register
			//enable the receiver chain again
			SpiWriteRegister(0x07, 0x05);													//write 0x05 to the Operating Function Control 1 register
		} 	
	}
}

/*+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
  +
  + FUNCTION NAME:  void MCU_Init(void)
  +
  + DESCRIPTION:   	This function configures the MCU 
  + 		
  + INPUT:			None
  +
  + RETURN:         None
  +
  + NOTES:          None
  +
  +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/
void MCU_Init(void)
{
	//Disable the Watch Dog timer of the MCU
   PCA0MD   &= ~0x40;                  
	
	// Set the clock source of the MCU: 10MHz, using the internal RC osc.
   CLKSEL    = 0x14;


   // Initialize the the IO ports and the cross bar
   P0SKIP  |= 0x40;                    // skip P0.6
   XBR1    |= 0x40;                    // Enable SPI1 (3 wire mode)
   P1MDOUT |= 0x01;                    // Enable SCK push pull
   P1MDOUT |= 0x04;                    // Enable MOSI push pull
   P1SKIP  |= 0x08;                    // skip NSS
   P1MDOUT |= 0x08;                    // Enable NSS push pull
   P1SKIP  |= 0x40;                    // skip TX_LED
   P1MDOUT |= 0x40;                    // Enable TX_LED push pull
   P2SKIP  |= 0x01;                    // skip RX_LED
   P2MDOUT |= 0x01;                    // Enable RX_LED push pull
	P0SKIP  |= 0x02; 					// skip SDN
	P0MDOUT |= 0x02;					// Enable SDN push pull
   P0SKIP  |= 0x80;                    // skip PB
   SFRPAGE  = CONFIG_PAGE;
   P0DRV    = 0x12;                   // TX high current mode
   P1DRV    = 0x4D;                   // MOSI, SCK, NSS, TX_LED high current mode
	P2DRV	  	= 0x01;					// RX_LED high current mode	
   SFRPAGE  = LEGACY_PAGE;
   XBR2    |= 0x40;                    // enable Crossbar

   // For the SPI communication the hardware peripheral of the MCU is used 
   //in 3 wires Single Master Mode. The select pin of the radio is controlled
	//from software
	SPI1CFG   = 0x40;					//Master SPI, CKPHA=0, CKPOL=0
   SPI1CN    = 0x00;					//3-wire Single Master, SPI enabled
   SPI1CKR   = 0x00;
   SPI1EN 	 = 1;                     	// Enable SPI interrupt
   NSS = 1;
	
	// Turn off the LEDs
	TX_LED = 0;
	RX_LED = 0;
}

/*+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
  +
  + FUNCTION NAME: void SpiWriteRegister(U8 reg, U8 value)
  +
  + DESCRIPTION:   This function writes the registers 
  + 					
  + INPUT:			 U8 reg - register address   
  +					 U8 value - value write to register	
  +
  + RETURN:        None
  +
  + NOTES:         Write uses a Double buffered transfer
  +
  +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/
void SpiWriteRegister (U8 reg, U8 value)
{
   // Send SPI data using double buffered write

	//Select the radio by pulling the nSEL pin to low
   NSS = 0;                            
   
   //write the address of the register into the SPI buffer of the MCU
	//(important to set the MSB bit)
	SPI1DAT = (reg|0x80);				//write data into the SPI register
	//wait until the MCU finishes sending the byte
	while( SPIF1 == 0);					
	SPIF1 = 0;
	//write the new value of the radio register into the SPI buffer of the MCU
	SPI1DAT = value;						//write data into the SPI register
	//wait until the MCU finishes sending the byte
	while( SPIF1 == 0);					//wait for sending the data
	SPIF1 = 0;	       
   //Deselect the radio by pulling high the nSEL pin
	NSS = 1;                            

}

/*+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
  +
  + FUNCTION NAME: U8 SpiReadRegister(U8 reg)
  +
  + DESCRIPTION:   This function reads the registers 
  + 					
  + INPUT:			 U8 reg - register address   
  +
  + RETURN:        SPI1DAT - the register content 
  +
  + NOTES:         none
  +
  +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/
U8 SpiReadRegister (U8 reg)
{

	//Select the radio by pulling the nSEL pin to low
	NSS = 0;                            
	//Write the address of the register into the SPI buffer of the MCU 
	//(important to clear the MSB bit)
   SPI1DAT = reg;								//write data into the SPI register
	//Wait untill the MCU finishes sending the byte
	while( SPIF1 == 0);						
	SPIF1 = 0;
	//Write a dummy data byte into the SPI buffer of the MCU. During sending 
	//this byte the MCU will read the value of the radio register and save it 
	//in its SPI buffer.
	SPI1DAT = 0xFF;							//write dummy data into the SPI register
	//Wait untill the MCU finishes sending the byte
	while( SPIF1 == 0);						
	SPIF1 = 0;
	//Deselect the radio by pulling high the nSEL pin
	NSS = 1;                            

	//Read the received radio register value and return with it
   return SPI1DAT;
}