main_sdbc_dk3.c

Si4432-T-B1版本资料.rar

/*
** ============================================================================
**
** FILE
**  main.c
**
** DESCRIPTION
**  This is the main file of the project.	    
**  HW platform SDB with C8051F93x Silabs MCU 
**
** CREATED
**  Silicon Laboratories Hungary Ltd
**
** COPYRIGHT
**  Copyright 2009 Silicon Laboratories, Inc.  
**	http://www.silabs.com
**
** ============================================================================
*/

								/* ======================================================== *
								 *									INCLUDE									*
							 	 * ======================================================== */


#include "C8051F930_defs.h"
#include "compiler_defs.h"
#include "string.h"

							/* ================================================================ *
							 * C8051F930 Pin definitions for Software Development Board         *
							 * 					(using compiler_def.h macros) 				    	  *
							 *	================================================================ */	

SBIT(NSS, SFR_P1, 3);
SBIT(NIRQ, SFR_P0, 6);
SBIT(PB1, SFR_P0, 0);
SBIT(PB2, SFR_P0, 1);
SBIT(PB3, SFR_P2, 0);
SBIT(PB4, SFR_P2, 1);
SBIT(LED1, SFR_P1, 4);
SBIT(LED2, SFR_P1, 5);
SBIT(LED3, SFR_P1, 6);
SBIT(LED4, SFR_P1, 7);

//One out of these definitions has to be uncommented which tells to the compiler what kind 
//of Testcard is plugged into the Software Development board
#define SEPARATE_RX_TX
//#define ANTENNA_DIVERSITY
//#define ONE_SMA_WITH_RF_SWITCH


								/* ======================================================== *
								 *							Function PROTOTYPES							* 		
								 * ======================================================== */
//MCU initialization
void MCU_Init(void);
//SPI functions						
void SpiWriteRegister (U8, U8);
U8 SpiReadRegister (U8);


void main(void)
{
	U8 ItStatus1,ItStatus2;
	U16 delay;
	U8 length,temp8;
	U8 payload[10];

	//Initialize the MCU: 
	//	- set IO ports for the Software Development board
	//	- set MCU clock source
	//	- initialize the SPI port 
	//	- turn off LEDs
	MCU_Init();
							/* ======================================================== *
							 *						Initialize the Si443x ISM chip				* 
							 * ======================================================== */

	//read interrupt status registers to clear the interrupt flags and release NIRQ pin
	ItStatus1 = SpiReadRegister(0x03);														//read the Interrupt Status1 register
	ItStatus2 = SpiReadRegister(0x04);														//read the Interrupt Status2 register
	
	//SW reset   
   SpiWriteRegister(0x07, 0x80);																//write 0x80 to the Operating & Function Control1 register 
	
	//wait for POR interrupt from the radio (while the nIRQ pin is high)
	while ( NIRQ == 1); 
	//read interrupt status registers to clear the interrupt flags and release NIRQ pin
	ItStatus1 = SpiReadRegister(0x03);														//read the Interrupt Status1 register
	ItStatus2 = SpiReadRegister(0x04);														//read the Interrupt Status2 register
 
	//wait for chip ready interrupt from the radio (while the nIRQ pin is high)
	while ( NIRQ == 1); 
	//read interrupt status registers to clear the interrupt flags and release NIRQ pin
	ItStatus1 = SpiReadRegister(0x03);														//read the Interrupt Status1 register
	ItStatus2 = SpiReadRegister(0x04);														//read the Interrupt Status2 register
				
							/*set the physical signal parameters*/
	//set the center frequency to 915 MHz
	SpiWriteRegister(0x75, 0x75);																//write 0x75 to the Frequency Band Select register             
   SpiWriteRegister(0x76, 0xBB);																//write 0xBB to the Nominal Carrier Frequency1 register
   SpiWriteRegister(0x77, 0x80); 															//write 0x80 to the Nominal Carrier Frequency0 register
	
								/*set the modem parameters according to the exel calculator(parameters: 9.6 kbps, deviation: 45 kHz, channel filter BW: 102.2 kHz*/
	SpiWriteRegister(0x1C, 0x1E);																//write 0x1E to the IF Filter Bandwidth register		
	SpiWriteRegister(0x20, 0xD0);																//write 0xD0 to the Clock Recovery Oversampling Ratio register		
	SpiWriteRegister(0x21, 0x00);																//write 0x00 to the Clock Recovery Offset 2 register		
	SpiWriteRegister(0x22, 0x9D);																//write 0x9D to the Clock Recovery Offset 1 register		
	SpiWriteRegister(0x23, 0x49);																//write 0x49 to the Clock Recovery Offset 0 register		
	SpiWriteRegister(0x24, 0x00);																//write 0x00 to the Clock Recovery Timing Loop Gain 1 register		
	SpiWriteRegister(0x25, 0x24);																//write 0x24 to the Clock Recovery Timing Loop Gain 0 register		
	SpiWriteRegister(0x1D, 0x40);																//write 0x40 to the AFC Loop Gearshift Override register		
	SpiWriteRegister(0x1E, 0x0A);																//write 0x0A to the AFC Timing Control register		
	SpiWriteRegister(0x2A, 0x20);																//write 0x20 to the AFC Limiter register		
		

							/*Configure the receive packet handler*/
	//Disable header bytes; set variable packet length (the length of the payload is defined by the
	//received packet length field of the packet); set the synch word to two bytes long
   SpiWriteRegister(0x33, 0x02);																//write 0x02 to the Header Control2 register    
	//Disable the receive header filters
   SpiWriteRegister(0x32, 0x00);																//write 0x00 to the Header Control1 register            
	
	//Set the sync word pattern to 0x2DD4
	SpiWriteRegister(0x36, 0x2D);																//write 0x2D to the Sync Word 3 register
	SpiWriteRegister(0x37, 0xD4);																//write 0xD4 to the Sync Word 2 register

	//Enable the receive packet handler and CRC-16 (IBM) check
	SpiWriteRegister(0x30, 0x85);																//write 0x85 to the Data Access Control register
	//Enable FIFO mode and GFSK modulation
	SpiWriteRegister(0x71, 0x63);										 						//write 0x63 to the Modulation Mode Control 2 register
	//set preamble detection threshold to 20bits
	SpiWriteRegister(0x35, 0x2A); 															//write 0x2A to the Preamble Detection Control  register

	//set the preamble length to 10bytes if the antenna diversity is used and set to 5bytes if not 
#ifdef ANTENNA_DIVERSITY
	SpiWriteRegister(0x34, 0x14); 															//write 0x14 to the Preamble Length register 	
#else
	SpiWriteRegister(0x34, 0x0A);																//write 0x0A to the Preamble Length register
#endif

#ifdef ANTENNA_DIVERSITY
	//Enable antenna diversity mode
	SpiWriteRegister(0x08, 0x80);																//write 0x80 to the Operating Function Control 2 register
#endif

											/*set the GPIO's according the testcard type*/
#ifdef ANTENNA_DIVERSITY
   SpiWriteRegister(0x0C, 0x17);																//write 0x17 to the GPIO1 Configuration(set the Antenna 1 Switch used for antenna diversity )
	SpiWriteRegister(0x0D, 0x18);																//write 0x18 to the GPIO2 Configuration(set the Antenna 2 Switch used for antenna diversity ) 
#endif
#ifdef ONE_SMA_WITH_RF_SWITCH
   SpiWriteRegister(0x0C, 0x12);																//write 0x12 to the GPIO1 Configuration(set the TX state)
	SpiWriteRegister(0x0D, 0x15);																//write 0x15 to the GPIO2 Configuration(set the RX state) 
#endif

											/*set the non-default Si443x registers*/
	//set  Crystal Oscillator Load Capacitance register
	SpiWriteRegister(0x09, 0xD7);																//write 0xD7 to the Crystal Oscillator Load Capacitance register

    
	/*enable receiver chain*/
	SpiWriteRegister(0x07, 0x05);																//write 0x05 to the Operating Function Control 1 register
	//Enable two interrupts: 
	// a) one which shows that a valid packet received: 'ipkval'
	// b) second shows if the packet received with incorrect CRC: 'icrcerror' 
	SpiWriteRegister(0x05, 0x03); 															//write 0x03 to the Interrupt Enable 1 register
	SpiWriteRegister(0x06, 0x00); 															//write 0x00 to the Interrupt Enable 2 register
	//read interrupt status registers to release all pending interrupts
	ItStatus1 = SpiReadRegister(0x03);														//read the Interrupt Status1 register
	ItStatus2 = SpiReadRegister(0x04);														//read the Interrupt Status2 register

	/*MAIN Loop*/
	while(1)
	{
	    //wait for the interrupt event
		if( NIRQ == 0 )
		{
			//disable the receiver chain 
			SpiWriteRegister(0x07, 0x01);														//write 0x01 to the Operating Function Control 1 register
			//read interrupt status registers 		
			ItStatus1 = SpiReadRegister(0x03);												//read the Interrupt Status1 register
			ItStatus2 = SpiReadRegister(0x04);												//read the Interrupt Status2 register

			/*CRC Error interrupt occured*/
			if( (ItStatus1 & 0x01) == 0x01 )
			{
				//reset the RX FIFO
       	   SpiWriteRegister(0x08, 0x02);													//write 0x02 to the Operating Function Control 2 register
        	   SpiWriteRegister(0x08, 0x00);													//write 0x00 to the Operating Function Control 2 register
				//blink all LEDs to show the error
				LED1 = 1;
				LED2 = 1;
				LED3 = 1;
				LED4 = 1;
				for(delay = 0; delay < 10000;delay++);
				LED1 = 0;
				LED2 = 0;
				LED3 = 0;
				LED4 = 0;
			}

			/*packet received interrupt occured*/