📄 remote_car.lis
字号:
.module remote_car.c
.area text(rom, con, rel)
0000 .dbfile e:/ICC/include/sl3010.c
0000 .dbfunc e port_init _port_init fV
.even
0000 _port_init::
0000 .dbline -1
0000 .dbline 83
0000 ; #include <io8515v.h>
0000 ; #include <macros.h>
0000 ; #include <sl3010.c>
0000 ;
0000 ; //声控起动遥控车程序，未起动时，PA口的8 LED 呈广告灯效果（霓虹灯）
0000 ; //声控起动后，机器人开始动作
0000 ; //遥控器无按键，机器人直行
0000 ; //按住 < A > 键，机器人右转，同时演奏右转指示音乐；
0000 ; //按住 < B > 键，机器人后退，同时演奏后退指示音乐；
0000 ; //按住 < C > 键，机器人停止，同时演奏停止指示音乐；
0000 ; //按住 < D > 键，机器人左转，同时演奏左转指示音乐；
0000 ; //释放遥控器按键，音乐停止
0000 ; //连续 按住 < C > 键时间超过 10s，遥控机器人复位，等待声控重新起动
0000 ;
0000 ; /* 音阶表 */
0000 ; const unsigned int TONETABLE[15]={DO,RE,MI,FA,SO,LA,TI,DO_H,
0000 ; RE_H,MI_H,FA_H,SO_H,LA_H,TI_H,DO_HH};
0000 ; /* 音阶重装常数 */
0000 ; unsigned int toneconst;
0000 ; unsigned int sound_add=0;
0000 ; unsigned int delay_time1,delay_time2,led_delayms=600;
0000 ; unsigned char temp,temp1;
0000 ; unsigned char pa,pb,pc,pd,remote_in,timers,cny_in,cny_times,rst_time,cds,pd_select,remote_select;
0000 ; unsigned char gzsl,t0_times;
0000 ; unsigned char sound_1,sound_2;
0000 ;
0000 ; const unsigned char led_data[]=
0000 ; {//设置LED广告灯数据表
0000 ; 0xfe,0xfd,0xfb,0xf7,0xef,0xdf,0xbf,0x7f,0xbf,0xdf,0xef,0xf7,0xfb,0xfd,
0000 ; 0xfe,0xfd,0xfb,0xf7,0xef,0xdf,0xbf,0x7f,0xbf,0xdf,0xef,0xf7,0xfb,0xfd,
0000 ; 0x00,0x18,0x3c,0x7e,0xff,0x7e,0x3c,0x18,
0000 ; 0x00,0x18,0x3c,0x7e,0xff,0x7e,0x3c,0x18,
0000 ; 0xf8,0xf1,0xe3,0xc7,0x8f,0x1f,0x8f,0xc7,0xe3,0xf1,
0000 ; 0xf8,0xf1,0xe3,0xc7,0x8f,0x1f,0x8f,0xc7,0xe3,0xf1,
0000 ; 0xfe,0xfc,0xf8,0xf0,0xe0,0xc0,0x80,0x00,0x80,0xc0,0xe0,0xf0,0xf8,0xfc,
0000 ; 0xfe,0xfc,0xf8,0xf0,0xe0,0xc0,0x80,0x00,0x80,0xc0,0xe0,0xf0,0xf8,0xfc,
0000 ; 0xff,0xe7,0xdb,0xbd,0x7e,0xbd,0xdb,0xe7,
0000 ; 0xff,0xe7,0xdb,0xbd,0x7e,0xbd,0xdb,0xe7,
0000 ; 0xff,0x00,0xff,0x00,0xff,0x00,0xff,0x00,
0000 ;
0000 ; 0x0a,0x0a
0000 ; };
0000 ;
0000 ; const unsigned char sound_none[]={0x28,0x27,0x36,0x16,0x45,0x47,0x46,0x46,0x46,0x23,0x25,0x46,0x4a,0x39,0x18,0x27,
0000 ; 0x28,0x48,0x48,0x28,0x27,0x36,0x16,0x45,0x27,0x26,0x46,0x46,0x46,0x46,0x46,0x46,0x00,0x00};
0000 ; const unsigned char sound_right[]={0x23,0x25,0x46,0x4a,0x39,0x18,0x27,0x28,0x48,0x48,0x48,
0000 ; 0x28,0x27,0x36,0x16,0x45,0x47,0x46,0x46,0x46,0x00,0x00};
0000 ; const unsigned char sound_back[]={0x2a,0x2c,0x4d,0x4d,0x4d,0x2a,0x2c,0x49,0x49,0x49,0x2a,0x2c,0x2d,0x4f,
0000 ; 0x2d,0x4c,0x1d,0x18,0x2a,0x49,0x49,0x49,0x00,0x00};
0000 ; const unsigned char sound_stop[]={0x23,0x24,0x25,0x44,0x45,0x24,0x23,0x22,0x42,0x40,0x40,0x23,0x22,0x21,0x41,0x28,
0000 ; 0x48,0x23,0x25,0x45,0x40,0x40,0x00,0x00};
0000 ; const unsigned char sound_left[]={0x68,0x26,0x25,0x23,0x22,0x13,0x12,0x41,0x41,0x41,0x23,0x25,
0000 ; 0x28,0x48,0x28,0x29,0x2a,0x29,0x26,0x45,0x45,0x45,0x00,0x00};
0000 ;
0000 ; //TIMER0 initialisation - prescale:1024
0000 ; // desired value: 25mSec
0000 ; // actual value: 24.960mSec (0.2%)
0000 ; void timer0_init(void)
0000 ; {
0000 ; TCCR0 = 0x00; //stop timer
0000 ; TCNT0 = 0x3D; //set count value
0000 ; TCCR0 = 0x05; //start timer
0000 ; }
0000 ;
0000 ; #pragma interrupt_handler timer0_ovf_isr:iv_TIMER0_OVF
0000 ; void timer0_ovf_isr(void)
0000 ; {
0000 ; TCNT0 = 0x3D; //reload counter value
0000 ; t0_times++;
0000 ; if(gzsl == 0x88)
0000 ; {
0000 ; if(t0_times == 10)
0000 ; {
0000 ; timers++;
0000 ; t0_times = 0;
0000 ; pa = led_data[timers];
0000 ; if(pa==0x0a){timers=0;}
0000 ; PORTA = pa;
0000 ; }
0000 ; }
0000 ; if(gzsl == 0x33)
0000 ; {
0000 ; sw_touch();
0000 .dbline 84
0000 ; if(t0_times == 8) //8*25ms=200ms
0000 8FEF ldi R24,255
0002 8ABB out 0x1a,R24
0004 .dbline 84
0004 8BBB out 0x1b,R24
0006 .dbline 85
0006 ; {
0006 80E8 ldi R24,128
0008 87BB out 0x17,R24
000A .dbline 85
000A 8FEF ldi R24,255
000C 88BB out 0x18,R24
000E .dbline 86
000E ; t0_times = 0;
000E 81E0 ldi R24,1
0010 84BB out 0x14,R24
0012 .dbline 86
0012 8FEF ldi R24,255
0014 85BB out 0x15,R24
0016 .dbline 87
0016 ; remote_in = PINB & 0x0F;
0016 80EF ldi R24,240
0018 81BB out 0x11,R24
001A .dbline 87
001A 8FEF ldi R24,255
001C 82BB out 0x12,R24
001E .dbline -2
001E .dbline 88
001E ; sound_1 = remote_in;
001E L1:
001E .dbline 0 ; func end
001E 0895 ret
0020 .dbend
0020 .dbfunc e delay_us _delay_us fV
0020 ; time -> R16,R17
.even
0020 _delay_us::
0020 .dbline -1
0020 .dbline 91
0020 ; if(sound_2 != sound_1)
0020 ; {sound_add=0;sound_2 = sound_1;}
0020 ; switch (remote_in)
0020 L3:
0020 .dbline 93
0020 ; {//检测遥控器是否有键按下
0020 ; case 0x00:
0020 .dbline 94
0020 ; forward(); //前行
0020 0150 subi R16,1
0022 1040 sbci R17,0
0024 .dbline 95
0024 ; rst_time=0;
0024 L4:
0024 .dbline 96
0024 ; sound_add=0x00;
0024 81E0 ldi R24,1
0026 90E0 ldi R25,0
0028 8017 cp R24,R16
002A 9107 cpc R25,R17
002C CCF3 brlt L3
002E .dbline -2
002E .dbline 97
002E ; temp1=0x00;
002E L2:
002E .dbline 0 ; func end
002E 0895 ret
0030 .dbsym r time 16 I
0030 .dbend
0030 .dbfunc e delay_ms _delay_ms fV
0030 ; time -> R20,R21
.even
0030 _delay_ms::
0030 00D0 rcall push_gset1
0032 402F mov R20,R16
0034 512F mov R21,R17
0036 .dbline -1
0036 .dbline 100
0036 ; break;
0036 ; case 0x04: // < A >
0036 ; turn_right(); //右转
0036 05C0 rjmp L8
0038 L7:
0038 .dbline 102
0038 .dbline 103
0038 08EE ldi R16,1000
003A 13E0 ldi R17,3
003C F1DF rcall _delay_us
003E .dbline 104
003E 4150 subi R20,1
0040 5040 sbci R21,0
0042 .dbline 105
0042 L8:
0042 .dbline 101
0042 ; rst_time=0;
0042 4030 cpi R20,0
0044 4507 cpc R20,R21
0046 C1F7 brne L7
0048 X0:
0048 .dbline -2
0048 .dbline 106
0048 ; temp1=sound_right[sound_add];
0048 ; break;
0048 ; case 0x02: // < B >
0048 ; backward(); //后退
0048 ; rst_time=0;
0048 L6:
0048 00D0 rcall pop_gset1
004A .dbline 0 ; func end
004A 0895 ret
004C .dbsym r time 20 i
004C .dbend
004C .dbfunc e turn_right _turn_right fV
.even
004C _turn_right::
004C .dbline -1
004C .dbline 109
004C ; temp1=sound_back[sound_add];
004C ; break;
004C ; case 0x08: // < C >
004C .dbline 110
004C ; stop(); //停止运动
004C 80E6 ldi R24,96
004E 82BB out 0x12,R24
0050 .dbline 111
0050 ; rst_time++;
0050 8CEC ldi R24,204
0052 8BBB out 0x1b,R24
0054 .dbline -2
0054 .dbline 112
0054 ; temp1=sound_stop[sound_add];
0054 L10:
0054 .dbline 0 ; func end
0054 0895 ret
0056 .dbend
0056 .dbfunc e turn_left _turn_left fV
.even
0056 _turn_left::
0056 .dbline -1
0056 .dbline 115
0056 ; break;
0056 ; case 0x01: // < D >
0056 ; turn_left(); //左转
0056 .dbline 116
0056 ; rst_time=0;
0056 80E9 ldi R24,144
0058 82BB out 0x12,R24
005A .dbline 117
005A ; temp1=sound_left[sound_add];
005A 83E3 ldi R24,51
005C 8BBB out 0x1b,R24
005E .dbline -2
005E .dbline 118
005E ; break;
005E L11:
005E .dbline 0 ; func end
005E 0895 ret
0060 .dbend
0060 .dbfunc e turn_right_s _turn_right_s fV
.even
0060 _turn_right_s::
0060 .dbline -1
0060 .dbline 120
0060 ; }
0060 ; }
0060 .dbline 121
0060 ; }
0060 80E2 ldi R24,32
0062 82BB out 0x12,R24
0064 .dbline 122
0064 ; }
0064 8FEC ldi R24,207
0066 8BBB out 0x1b,R24
0068 .dbline -2
0068 .dbline 123
0068 ;
0068 L12:
0068 .dbline 0 ; func end
0068 0895 ret
006A .dbend
006A .dbfunc e turn_left_s _turn_left_s fV
.even
006A _turn_left_s::
006A .dbline -1
006A .dbline 126
006A ; void stop_timer0()
006A ; {
006A ; CLI();
006A .dbline 127
006A ; TCCR0 = 0x00;//停止timer0
006A 80E8 ldi R24,128
006C 82BB out 0x12,R24
006E .dbline 128
006E ; MCUCR = 0x00;
006E 83EF ldi R24,243
0070 8BBB out 0x1b,R24
0072 .dbline -2
0072 .dbline 129
0072 ; GIMSK = 0x00;
0072 L13:
0072 .dbline 0 ; func end
0072 0895 ret
0074 .dbend
0074 .dbfunc e backward _backward fV
.even
0074 _backward::
0074 .dbline -1
0074 .dbline 132
0074 ; TIMSK = 0x00;
0074 ; SEI();
0074 ; }
0074 .dbline 133
0074 ;
0074 80E5 ldi R24,80
0076 82BB out 0x12,R24
0078 .dbline 134
0078 ; #pragma interrupt_handler timer1_ovf_isr:iv_TIMER1_OVF
0078 8CE3 ldi R24,60
007A 8BBB out 0x1b,R24
007C .dbline -2
007C .dbline 135
007C ; void timer1_ovf_isr(void)
007C L14:
007C .dbline 0 ; func end
007C 0895 ret
007E .dbend
007E .dbfunc e forward _forward fV
.even
007E _forward::
007E .dbline -1
007E .dbline 138
007E ; {
007E ; {
007E ; TCNT1=toneconst;
007E .dbline 139
007E ; PORTC^=1;
007E 80EA ldi R24,160
0080 82BB out 0x12,R24
0082 .dbline 140
0082 ; }
0082 83EC ldi R24,195
0084 8BBB out 0x1b,R24
0086 .dbline -2
0086 .dbline 141
0086 ; }
0086 L15:
0086 .dbline 0 ; func end
0086 0895 ret
0088 .dbend
0088 .dbfunc e stop _stop fV
.even
0088 _stop::
0088 .dbline -1
0088 .dbline 144
0088 ;
0088 ; void remote_car()
0088 ; {//遥控车程序
0088 .dbline 145
0088 ;
0088 8FEF ldi R24,255
008A 82BB out 0x12,R24
008C .dbline 146
008C ; port_init();//调用端口初始化函数
008C 8BBB out 0x1b,R24
008E .dbline -2
008E .dbline 147
008E ;
008E L16:
008E .dbline 0 ; func end
008E 0895 ret
0090 .dbend
0090 .dbfunc e sw_touch _sw_touch fV
.even
0090 _sw_touch::
0090 .dbline -1
0090 .dbline 163
0090 ; work_status = 0x60;//置对应的工作状态标志
0090 ;
0090 ; remote_rst:
0090 ; PORTA = 0x0F;
0090 ;
0090 ; gzsl=0x88;timers=0;t0_times=0;
0090 ; CLI(); //disable all interrupts
0090 ; timer0_init();
0090 ;
0090 ; MCUCR = 0x00;
0090 ; GIMSK = 0x00;
0090 ; TIMSK|=(1<<TOIE0);
0090 ; SEI(); //re-enable interrupts
0090 ;
0090 ; mic_startup();//等待声控启动函数
0090 ;
0090 .dbline 164
0090 ; gzsl=0x33;t0_times=0;
0090 83B3 in R24,0x13
0092 8071 andi R24,16
0094 80931900 sts _sw_in,R24
0098 .dbline 165
0098 ; TCCR1A = 0x00;
0098 8823 tst R24
009A C9F4 brne L18
009C .dbline 166
009C ; TCCR1B =(1<<CS11);//8分频
009C .dbline 167
009C ; n01:
009C EBDF rcall _backward
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -