machmin.msg

Protel99-SE-软件.zip

101 MACHMIN [...]     Minimize tre file and put result back to tre file.
101       -tre2pla    Convert tre file to pla file.
101       -efast      Fast minimization (faster but not optimal).
101       -log <file> Capture screen messages to disk file.
101       -?          Print out help screen.
101       -tre        [trefile[.ext]] input and output tre file
101       -pla        [plafile[.ext]] input and output pla file
101       -p <number> Gate splitting.
101       -a          Polarity as specified
101       -ao         Best polarity selection
101       -ah         Active-high polarity selection
101       -al         Active-low polarity selection
101       -dt         Convert to the best of D or T register logic.
101       -d          Convert to D register logic.
101       -t          Convert to T register logic.
101       -id         Convert only JK and RS to D register logic.
101       -it         Convert only JK and RS to T register logic.
101       -idt        Convert only JK and RS to the best of D or T.
101     DEFAULTS:
101       log file extension: .LOG.
101       log file name: MACHXL2.LOG.
101       input-output file extensions: .TRE
101       input-output filenames: MACHXL2.TRE
103 |> WARNING L102 Log filename %s is same as input or output filename.
103              Defaulting log filename to PALASM2.LOG.
104 |> ERROR L104 Input filename %s is same as output filename.
105 |> ERROR L105 Output filename %s is same as input filename.
106 |> ERROR L106 Auxiliary input filename %s is same as input filename.
107 |> ERROR L107 Auxiliary output filename %s is same as output filename.
108 |> ERROR L108 %s parameter argument "%s" is not a number.
109 |> ERROR L109 tre to tre translation is not supported.
110 |> ERROR L110 pla to pla translation is not supported.
111 |> ERROR L111 blif translation is not supported.
112 |> ERROR L112 -auxi flag is not supported for tre to pla translation.
113 |> ERROR L113 -auxo flag is not supported for pla to tre translation.
114 |> ERROR L114  Insufficient number of parameters (%s) specified.
114                At least two are required, either (tre pla) or (pla tre).
114                   For help, please use command line option -help.
115 |> ERROR L115  Illegal use of optional parameter %s.
116 |> ERROR L116  Unknown command line option "%s" found.
117 |> ERROR L117  Invalid first two command-line parameters (%s) found.
117                Should be (tre pla) or (pla tre).
118 |> ERROR L118  No argument after %s parameter.  Should be a number.
119 |> ERROR L119  Minimize specific processing options may not be used
119                with any pla file translation options.
120 %s
121 |> ERROR L121 -th parameter argument %s is not a number.
122 |> ERROR L122 The options -th and -p must both exist if you specify
122              one of them.
123 |> WARNING L123 Threshold must be greater than or equal to the 
123                "gate split max num pterms per equation".  
123                Resetting the latter number equal to Threshold.
124 |> ERROR L124  No argument after -f parameter.  Must be tre2tre or tre2pla.
125 |> WARNING L125 Error -f parameter argument %s.
125               Must be "-f tre2tre" or "-f tre2pla".
130 |> ERROR L130  You can specify only one or none of the following options.
130               Register transform options: -d, -t, -dt, -id, -it, and -idt.
135 |> ERROR L135  You can specify only one or none of the following options.
135               Polarity control options, -a, -ao, -ah, and -al.
200
210 |> ERROR L210 pla to tre translation is not supported.
215 |> ERROR L215 pla to pla translation is not supported.
300
400
401 |> INTERNAL_ERROR L401 Input tre file Equations section is corrupted.
402 |> ERROR L402 Number of signals in equation exceeds max limit (64).
500
501 |> ERROR L501 Cannot open input file %s
502 |> ERROR L502 Cannot open output file %s
502	Call AMD, 1-800-222-9323.
503 |> SYSTEM_ERROR L503 Input file %s cannot be closed.
503	Call AMD, 1-800-222-9323.
504 |> SYSTEM_ERROR L504 Output file %s cannot be closed.  
504          Possibly disk too full.
505 |> SYSTEM_ERROR L605 Program abnormally terminated due to the
505			 failure in executing a system call.
505     Possibly not enough memory.
506 |> SYSTEM_WARNING L506 Input file %s cannot be opened.
507 |> SYSTEM_ERROR L507 Cannot rename file from %s to %s.
508 |> SYSTEM_ERROR L508 Cannot open input file %s.
600 
700 
800 
801  \nTranslation input was read from input file %s.
802  Auxiliary input was read from auxiliary input file %s.
803  Translated output is stored in output file %s.
804  Auxiliary output is stored in auxiliary output file %s.
810 |> ERROR L810 Input file %s is corrupted.
820 |> INTERNAL ERROR L820
820    Duplicate equation %s found in the design.
830 |> ERROR L830 Error clock %s (pin number = %d) found in 
830    input register equation %s.   Must be a global clock-pin.
830 |> ERROR L830  Equation %s is an input-register/latch.
830               So product-term clock %s is not valid.
835 |> ERROR L835  Equation %s has SETF and RSTF non-GND.
835               So product-term clock %s is not valid.
840 |> ERROR L840  Equation %s is an input-register/latch.
840               So product-term clock %s is not valid.
850 |> ERROR L850  Equation %s has SETF and RSTF non-GND.  
850               So product-term clock %s is not valid.
855 Converting TRE file %s to PLA file %s...\n
857 Converting TRE file %s to BLIF file %s...\n
860 Converting PLA file %s to TRE file %s...\n
861 Converting PLA file %s to BLIF file %s...\n
862 \nThey are equivalent.
864 \nThey are NOT equivalent.
865 Verifying PLA files %s and %s ...
900
1000
1001 |> SYSTEM_ERROR L1001 Error in reading .i directive from  PLA file.
1002 |> ERROR L1002 .i directive must appear before .o directive.
1003 |> SYSTEM_ERROR L1003 Error in reading .o directive from PLA file.
1004 |> ERROR L1004 Invalid .o outputs (%d): use -mo for multi-output PLA.
1005 |> ERROR L1005 illegal type %s found in .type directive.
1006 |> ERROR L1006 .i & .o directives must appear before .ilb & .ob directives.
1007 |> SYSTEM_ERROR L1007 Error in reading labels from PLA file.
1008 |> ERROR L1008 .i & .o directives must appear before .phase directive.
1009 |> ERROR L1009 illegal phase found in .phase directive.
1010 |> WARNING L1010 product term spans more than one line.
1011 |> ERROR L1011 illegal variable size (%d) found.
1012 |> WARNING L1012 bad character found: line no %d ignored.
1013 |> WARNING L1013 extra .i directive found: ignored.
1014 |> WARNING L1014 extra .o directive found: ignored.
1015 |> WARNING L1015 extra .phase directive found: ignored.
1016 |> ERROR L1016 DEVICE must be specified before PIN declaration.
1017 |> ERROR L1017 PIN declaration cannot succeed NODE declaration.
1018 |> ERROR L1018 PIN declaration must precede NODE declaration.
1019 |> ERROR L1019 Missing #AMD DEVICE declaration in PLA file.
1020 |> ERROR L1020 Missing #AMD PIN declaration in PLA file.
1021 |> ERROR L1021 Invalid #AMD NODE declaration for this device.
1022 |> ERROR L1022 Too many input variables specified: may not exceed 64.
1023 |> ERROR L1023 Too many output variables specified: may not exceed
1023               pin+node count for this device.                
1024 |> ERROR L1024 Undefined input label %s found in .ilb directive.
1025 |> ERROR L1025 Undefined output label %s found in .ob directive.
1100
1101 |> INTERNAL_ERROR L1101 Tre file read error.
1101	 Call AMD, 1-800-222-9323.
1200
1201 Processing equation for ====>%s
1205 Processing equation(s) for %s...
1208 Minimizing %s...
1210 ====> %s MIN_ON (%s, %d %s pt --> %s, %d %s pt)
1220 ====> %s MIN_ON (%d %s pt --> %d %s pt)
1230 ====> %s MIN_ON (%d %s pt)
1240 ====> %s MIN_OFF (%d %s pt)
1245 ====> %s (%d %s pt)