cl.txt

Protel99-SE-软件.zip

0379:Pin '%s' must be declared with a CEPIN statement !
0380:Duplicate 'CE' declared for pin '%s' !
0381:Pin '%s' has been declared with different polarities !
0382:Pin '%s' has been  declared with different pin types !
0383:Pin '%s' is NOT declared in the pin-list of this pld !
0384:This  pin statement is NOT allowed for PLD Components !
0385:NODE pin '%s' is NOT used as an output. Cannot have UIM option !
0386:Expected either 'STD' or 'LOW' after 'PWR' !
0387:Uim equation output pin '%s' cannot be used in an PWR statement !
0388:PWR statement pin '%s' is not an output with equations!
     Remove from PWR statement.
0389:Expected either 'ON' or 'OFF' after 'PINTRST' !
0390:Uim equation output pin '%s' cannot be used in an PINTRST statement !
0391:Pin '%s' used in NODETRST statement is not an output pin !
0392:'PINTRST' statement is not allowed for whole designs !
            Use 'PINTRST' as an option in 'OUTPUTPIN' and 'IOPIN' statements !
0393:FASTINPUT pin '%s' is not used as an input in this equation file !
0394:Pin '%s' can not be defined as both a FASTCLOCK and a FASTINPUT !
0395:1:This pld type can not exceed the resources of one function block. 
            PARTITION statement is redundant and therefore ignored !
0396:INPUTPIN '%s' has CE declared but no RCLK !
0397:1:Design contains PIN_ATTRIBUTE statement(s), which will be 
       obsoleted in a later release. Use statements such as: INPUTPIN,
       OUTPUTPIN, IOPIN, NODE, FASTCLOCK, CEPIN and FOEPIN !
0398:1:Pal contains PIN_ATTRIBUTE statement(s), which will be obsoleted
       in a later release. Use statements such as: NODE, FASTCLOCK,
       FASTINPUT and NODETRST ON/OFF !
0399:Pin '%s' has more than one pterm declared for UIM equation !
0400:'%s' is NOT used as an output in any equation. Redeclare as an INPUTPIN !
0401:1:PIN_ATTRIBUTE ignored for pin '%s' since it is declared
     with a IOPIN, INPUTPIN, OUTPUTPIN, CEPIN, NODE, FASTCLOCK, or FOEPIN !
0402:Pin '%s' declared as PINTRST, but is missing a '.TRST' equation !
0403:Found a second PINTRST statement. Only one such statement allowed !
0404:This statement is NOT supported for the target device !
0405:1:Statement NOT supported for the target device and is being ignored !
0406:Pin statement option is NOT supported for the target device !
0407:'NODE (UIM) %s' is declared, but that pin has no proper
          '<pin_name>  =  <one_product_term>' equation !
0408:1:Extensions .FI and .PIN are not allowed for NODE '%s'.
     The extension is ignored !
0409:'%s.PIN' is not declared with an IOPIN or an INPUTPIN statement !
0410:1:IOPIN '%s' is not used as I/O and is being redeclared as OUTPUTPIN !
0411:[Internal Testing] Net '%s' has no sinks ! 
0412:[Internal Testing] Net '%s' has no sources ! 
0413:[Internal Error] Global pin id '%s' doesn't exist !
0414:Fast input pins are not available in target device !
0415:Fast input pin '%s' may only be used by an output pin, which is
     targeted for a Fast Function Block !
0416:Pin-statement can only be used in top-level files!
   INPUTPIN, OUTPUTPIN, IOPIN, CEPIN and FOEPIN can not be used in a
   schematic pld and pld include file.
0417:MRINPUT statement can only be used in top-level files !
        Use schematic component attribute "MRINPUT=ON" instead.
0418:1:MRINPUT statement is ignored! Target device has no configurable reset.
0419:Output '%s' uses both :+: and .ADDMODE. Please use .D1 XOR .D2 notation
     to declare which pterms go one each side of the :+: operator.
0420:Output '%s' uses both :+: and .SHIFT. Please use .D1 XOR .D2 notation
     to declare which pterms go one each side of the :+: operator.
0421:Output '%s' uses both :+: and .FBK. Please use .D1 XOR .D2 notation
     to declare which pterms go one each side of the :+: operator.
0422:1:The .RCLK and the .LCLK syntax will be obsoleted in a later
  release. RCLK and LE can be specified in the declaration section where pins
  are declared.
0423:OPTIONS statements are ignored in PLD files.
0424:Expected either 'ON' or 'OFF' after 'OPTIONS' statement !
0425:Option '%s' has been declared both 'OFF' and 'ON' !
0426:Missing or unknown option ! Valid options are CLOCK_OPT, FOE_OPT,
  UIM_OPT and REG_OPT.
0427:Option 'FOE_OPT' is not available on target device !
0428:CEPIN pins are not allowed in this equation !
0429:Dot extensions '.FI' and '.PIN' are NOT allowed in PLD files.
     Use  FASTINPUT statement for fast-inputs !
0430:Included PLD file (or PALCONVT file) '%s' contains fatal errors !
0431:Unable to open a temporary file. System Error???!!! Check available
     disk space.
0432:The top level file '%s' has identical filename in 
    an INCLUDE_EQN statement.
0433:INCLUDE_EQN statements are only allowed in top-level files.
     Remove the INCLUDE_EQN statements from any of the "included" files.
0434:%s
0435:1:Top-level file pintype declaration for pin '%s' overrides FASTCLOCK
    declaration in include file !
0436:Unable to create equation output file '%s' ! System Error???!!!
     Check available disk space.
0437:Identifier '%s' has a non-printable character !
0438:Only one LOGIC_OPT statement is allowed in the design !
0439:PARTITION FB, PARTITION FFB, FAST and LOGIC_OPT statements are
     only allowed in top-level files. Remove them from pld or include files !
0440:Unknown pin '%s'. It needs to be declared !
0441:Pin '%s' is specified to be put both in a High Density Function
     Block and in a Fast Function Block !
0442:1:PARTITION FFB is not valid for target device and is being ignored !
0443:Expected either 'ON' or 'OFF' after 'LOGIC_OPT' !
0444:Pin '%s' used in LOGIC_OPT statement is not an output with equations!
0445:1:This equation can not start with a slash '/' and the slash is being
    ignored.
0446:FFB output '%s' has been declared with both a .RSTF and 
     a .SETF equation. Only one is allowed or redeclared for high-density FB.
0447:FFB output '%s' has a .RSTF equation which is not allowed
    for target device !
0448:Pin assignments can not be used in NODE statements !
0449:Pin '%s' has been assigned to more than one pad pin !
0450:Pin assignment do not match the number of pin names in this statement !
0451:Conflicts exist between pal outputs.
Look for CONFLICTs in the Connectivity column in the Interconnect Report !
(If Log Report has other fatal errors, the Interconnect Report may not exist.)
0452:No conflicts found between included pal outputs !
0453:The FBKINVERT equation can only be set to VCC !
0454:FFB output '%s' cannot have a FBKINVERT equation !
0455:Cannot set FBKINVERT for a non-equation output '%s' !
0456:obsolete message
0457:T-flipflop for '%s' is declared active-low and targeted for a
    Fast Function Block, which is not supported. Rewrite it active-high.
0458: &= syntax is obsolete! Redeclare signal as NODE (UIM).
0459:1:FASTCLOCK '%s' is not used to clock anything in this design !
0460:1:FOEPIN '%s' is not used to enable anything in this design !
0461:1:CEPIN '%s' is not used to enable anything in this design !
0462:Output '%s' has %d product terms !
     This equation will increase the collapser and minimizer runtime and
     may also cause the system to run out of memory. Consider factoring
     your logic into multiple equations.
0463:The pin list must begin directly after the pldtype in the CHIP statement!
      Example:     CHIP  DESIGN_A    COMPONENT 
                   IN1  IN2  IN3  IN4  OUT1  OUT2  OUT3
0464:Expected either 'ON' or 'OFF' after 'NODETRST' !
0465:'NODETRST' statement is not allowed for top-level pld files !
     Use 'NODETRST' as an option in 'NODE','OUTPUTPIN' and 'IOPIN' statements !
0466:Only one NODETRST statement is allowed for PLD files.
0467:1:The PINTRST statement is no longer supported and is being ignored.
     Pin-tristated outputs are now default.
     To tristate internal feedbacks, use the new syntax NODETRST.
     To run old designs with old PINTRST syntax, add this line to
     the 'xepld.cfg' config file:
         ( alias NODETRST  ON ) 
  
0468:1:NODETRST is overridden by ( alias NODETRST ON ) found in 
  the 'xepld.cfg' config file.
0469:NODETRST alias value '%s' found in 'xepld.cfg' config file
    is unknown ! Change it to ON  or OFF.
0470:Option 'NODETRST' can only be used in NODE, IOPIN and OUTPUTPIN 
  statements !
0471:1:Tristate set to ground ! It will permanently disable the signal.
0472:1:The design has tristated equation output(s) which are not 
     declared with 'NODETRST'. These equation outputs will be treated
     as if they where declared with 'NODETRST' since the target device
     supports only 'NODETRST'.
0473:Pin '%s' is used as a fast input. Fast inputs are not supported
     on the current device!
0474:Running out of memory in the lower 640KB conventional memory area.
     Try again after removing TSRs, network drivers, etc.
     If called from XEMAKE, choose instead commands FITEQN and MAKEPRG, which
     use less of the 640KB memory area.
     Use the EMM386 program to move TSRs, drivers, etc. to the upper memory
     area may also help. See the MS-DOS manual.
0475:Pin '%s' uses pad latch or pad register.
     Not allowed for the target device!
0476:Equation output '%s' using arithmetic mode must be in 
     a PARTITION statement defining order relative other equation outputs.
0477:Equation output '%s' using .EXPORT or .SHIFT must be in 
     a PARTITION statement defining order relative other equation outputs.
0478:1:PWR statement is ignored! Target device has no power control.
0479:The right side of the equation uses vector notation. The left side
     also needs vector notatation with the same number of elements !
0480:Previous vector in current equation had %s elements.
     This vector should have the same number of elements !
0481:Pin '%s' used in FAST statement is an internal node!
0482:Only one FAST statement is allowed !
       List all signals with fast slew rate in one statement, e.g.,
          FAST ON x1 x2
                       x3 x4 ;continued on the next line if necessary
0483:Expected either 'ON' or 'OFF' after 'FAST' to control slew rate !
0484:Pin '%s' used in FAST statement is not an output with equations!
0485:1:FAST statement is ignored! Target device has no slew rate control.
#
# general component compiler messages
0500:Incorrect command line !
0501:Number out of range !
0502:Abort due to Errors !
0503:Bitmaps must be defined with hex or binary numbers !
0504:Bitmap does not have this many rows !
0505:Bitmap does not have this many inputs (columns) !
#
# end of file
#