sysvdlg.dat

Autocad-2005-简体中文-解密版.zip

!DIMGAP|Real|Drawing|0.0900
Sets the distance around the dimension text when the dimension line breaks to accommodate dimension text. Also sets the gap between annotation and a hook line created with the LEADER command. If you enter a negative DIMGAP value, AutoCAD places a box around the dimension text.\n\nAutoCAD also uses DIMGAP as the minimum length for pieces of the dimension line. When calculating the default position for the dimension text, it positions the text inside the extension lines only if doing so breaks the dimension lines into two segments at least as long as DIMGAP. Text placed above or below the dimension line is moved inside only if there is room for the arrowheads, dimension text, and a margin between them at least as large as DIMGAP: 2 * (DIMASZ + DIMGAP).\n\nDIMGAP also sets the gap between a tolerance symbol and its feature control frame.
!DIMJUST|Integer|Drawing|0
Controls the horizontal positioning of dimension text.\n\n0\tCentered along the dimension line between the extension lines\n1\tNext to the first extension line\n2\tNext to the second extension line\n3\tAbove and aligned with the first extension line\n4\tAbove and aligned with the second extension line
!DIMLDRBLK|String|Drawing|0
Specifies the arrow type for leaders. To turn off arrowhead display, enter a single period (.). For a list of arrowheads, see DIMBLK.
!DIMLFAC|Real|Drawing|1.0000
Sets a scale factor for linear dimension measurements. All linear dimension distances, including radii, diameters, and coordinates, are multiplied by DIMLFAC before being converted to dimension text.\n\nDIMLFAC has no effect on angular dimensions, and is not applied to the values held in DIMRND, DIMTM, or DIMTP.\n\nIf you create a dimension in paper space and DIMLFAC is not set to zero, AutoCAD multiplies the distance measured by the absolute value of DIMLFAC. In model space, negative values for DIMLFAC are ignored, and the value 1.0 is used instead.\n\nAutoCAD computes a value for DIMLFAC if you try to change DIMLFAC from the Dim prompt while in paper space and you select the Viewport option.\n\nDim: dimlfac\nCurrent value <1.0000> New value (Viewport): v\nSelect viewport to set scale:\n\nAutoCAD calculates the scaling of model space to paper space and assigns the negative of this value to DIMLFAC.
!DIMLIM|Switch|Drawing|Off
Generates dimension limits as the default text. Setting DIMLIM to on turns DIMTOL off.\n\nOff\tDimension limits are not generated as default text\nOn\tDimension limits are generated as default text
!DIMLUNIT|Integer|Drawing|Off
Sets units for all dimension types except Angular.\n\n1\tScientific\n2\tDecimal\n3\tEngineering\n4\tArchitectural\n5\tFractional\n6\tWindows desktop
!DIMLWD|Enum|Drawing|-2
Assigns lineweight to dimension lines.\n\n-2\tSets the lineweight to "ByBlock."\n-3\tSets the lineweight to "ByLayer."\nOther valid values entered in millimeters include 0, 5, 9, 13, 15, 18, 20, 25, 30, 35, 40, 50, 53, 60, 70, 80, 90, 100, 106, 120, 140, 158, 200, and 211.\n\nAll values must be entered in millimeters. (Multiply a value by 2.54 to convert values from inches to millimeters.)
!DIMLWE|Enum|Drawing|-2
Assigns lineweight to extension lines.\n\n-2\tSets the lineweight to "ByBlock."\n-3\tSets the lineweight to "ByLayer."\nOther valid values entered in millimeters include 0, 5, 9, 13, 15, 18, 20, 25, 30, 35, 40, 50, 53, 60, 70, 80, 90, 100, 106, 120, 140, 158, 200, and 211.\n\nAll values must be entered in millimeters. (Multiply a value by 2.54 to convert values from inches to millimeters.)
!DIMPOST|String|Drawing|""
Specifies a text prefix or suffix (or both) to the dimension measurement. For example, to establish a suffix for millimeters, set DIMPOST to mm; a distance of 19.2 units would be displayed as 19.2 mm.\n\nIf tolerances are turned on, the suffix is applied to the tolerances as well as to the main dimension.\n\nUse <> to indicate placement of the text in relation to the dimension value. For example, enter <>mm to display a 5.0 millimeter radial dimension as "5.0mm." If you entered mm <>, the dimension would be displayed as "mm 5.0." Use the <> mechanism for angular dimensions.
!DIMRND|Real|Drawing|0.0000
Rounds all dimensioning distances to the specified value. For instance, if DIMRND is set to 0.25, all distances round to the nearest 0.25 unit. If you set DIMRND to 1.0, all distances round to the nearest integer. Note that the number of digits edited after the decimal point depends on the precision set by DIMDEC. DIMRND does not apply to angular dimensions.
!DIMSAH|Switch|Drawing|Off
Controls the display of dimension line arrowhead blocks.\n\nOff\tUse arrowhead blocks set by DIMBLK\nOn\tUse arrowhead blocks set by DIMBLK1 and DIMBLK2
!DIMSCALE|Real|Drawing|1.0000
Sets the overall scale factor applied to dimensioning variables that specify sizes, distances, or offsets. Also affects the scale of leader objects created with the LEADER command.\n\n0.0\tAutoCAD computes a reasonable default value based on the scaling between the current model space viewport and paper space. If you are in paper space or model space and not using the paper space feature, the scale factor is 1.0.\n>0\tAutoCAD computes a scale factor that leads text sizes, arrowhead sizes, and other scaled distances to plot at their face values.\n\nDIMSCALE does not affect tolerances or measured lengths, coordinates, or angles.
!DIMSD1|Switch|Drawing|Off
Controls suppression of the first dimension line.\n\nWhen turned on, suppresses the display of the dimension line and arrowhead between the first extension line and the text.
!DIMSD2|Switch|Drawing|Off
Controls suppression of the second dimension line.\n\nWhen turned on, suppresses the display of the dimension line and arrowhead between the second extension line and the text.
!DIMSE1|Switch|Drawing|Off
Suppresses display of the first extension line.\n\nOff\tExtension line is not suppressed\nOn\tExtension line is suppressed
!DIMSE2|Switch|Drawing|Off
Suppresses display of the second extension line.\n\nOff\tExtension line is not suppressed\nOn\tExtension line is suppressed
!DIMSHO|Switch|Drawing|On
Obsolete. Has no effect except to preserve the integrity of scripts.\n\nIn versions of AutoCAD prior to 2004 it controled the redefinition of dimension objects while dragging. Associative dimensions recompute dynamically as they are dragged. On some computers, dynamic dragging can be very slow, so, set DIMSHO to off to drag the original image instead. DIMSHO is not stored in a dimension style.
!DIMSOXD|Switch|Drawing|Off
Suppresses drawing of dimension lines outside the extension lines.\n\nOff\tDimension lines are not suppressed\nOn\tDimension lines are suppressed\n\nIf the dimension lines would be outside the extension lines and DIMTIX is on, setting DIMSOXD to on suppresses the dimension line. If DIMTIX is off, DIMSOXD has no effect.
#DIMSTYLE|String|Drawing|
DIMSTYLE is both a command and a system variable. The DIMSTYLE system variable shows the current dimension style. To display the DIMSTYLE system variable, use the SETVAR command. The DIMSTYLE system variable is read-only; you cannot change its value on the command line. To change the current dimension style, use the DIMSTYLE command.
!DIMTAD|Integer|Drawing|0
Controls the vertical position of text in relation to the dimension line.\n\n0\tCenters the dimension text between the extension lines.\n1\tPlaces the dimension text above the dimension line except when the dimension line is not horizontal and text inside the extension lines is forced horizontal (DIMTIH = 1). The distance from the dimension line to the baseline of the lowest line of text is the current DIMGAP value.\n2\tPlaces the dimension text on the side of the dimension line farthest away from the defining points.\n3\tPlaces the dimension text to conform to Japanese Industrial Standards (JIS).
!DIMTDEC|Integer|Drawing|4
Sets the number of decimal places to display in tolerance values for the primary units in a dimension.
!DIMTFAC|Real|Drawing|1.0000
Sets a scale factor used to calculate the height of text for dimension fractions and tolerances. AutoCAD multiplies DIMTXT by DIMTFAC to set the fractional or tolerance text height.
!DIMTIH|Switch|Drawing|On
Controls the position of dimension text inside the extension lines for all dimension types except ordinate.\n\nOff\tAligns text with the dimension line\nOn\tDraws text horizontally
!DIMTIX|Switch|Drawing|Off
Draws text between extension lines.\n\nOff\tVaries with the type of dimension. For linear and angular dimensions, AutoCAD places text inside the extension lines if there is sufficient room. For radius and diameter dimensions that don't fit inside the circle or arc, DIMTIX has no effect and always forces the text outside the circle or arc.\nOn\tDraws dimension text between the extension lines even if AutoCAD ordinarily places it outside those lines.
!DIMTM|Real|Drawing|0.0000
Sets the minimum (or lower) tolerance limit for dimension text when DIMTOL or DIMLIM is on. AutoCAD accepts signed values for DIMTM. If DIMTOL is on and DIMTP and DIMTM are set to the same value, AutoCAD draws a tolerance value.\n\nIf DIMTM and DIMTP values differ, the upper tolerance is drawn above the lower, and a plus sign is added to the DIMTP value if it is positive.\n\nFor DIMTM, AutoCAD uses the negative of the value you enter (adding a minus sign if you specify a positive number and a plus sign if you specify a negative number).
!DIMTMOVE|Integer|Drawing|0
Sets dimension text movement rules.\n\n0\tMoves the dimension line with dimension text\n1\tAdds a leader when dimension text is moved\n2\tAllows text to be moved freely without a leader
!DIMTOFL|Switch|Drawing|Off
Controls whether a dimension line is drawn between the extension lines even when the text is placed outside. For radius and diameter dimensions (when DIMTIX is off), draws a dimension line inside the circle or arc and places the text, arrowheads, and leader outside.\n\nOff\tDoes not draw dimension lines between the measured points when arrowheads are placed outside the measured points\nOn\tDraws dimension lines between the measured points even when arrowheads are placed outside the measured points
!DIMTOH|Switch|Drawing|On
Controls the position of dimension text outside the extension lines.\n\nOff\tAligns text with the dimension line\nOn\tDraws text horizontally
!DIMTOL|Switch|Drawing|Off
Appends tolerances to dimension text.\n\nOff\tNo tolerance is used or added\nOn\tTolerance is added and DIMLIM is turned off.
!DIMTOLJ|Integer|Drawing|1
Sets the vertical justification for tolerance values relative to the nominal dimension text.\n\n0\tBottom\n1\tMiddle\n2\tTop
!DIMTP|Real|Drawing|0.0000
Sets the maximum (or upper) tolerance limit for dimension text when DIMTOL or DIMLIM is on. AutoCAD accepts signed values for DIMTP. If DIMTOL is on and DIMTP and DIMTM are set to the same value, AutoCAD draws a tolerance value.\n\nIf DIMTM and DIMTP values differ, the upper tolerance is drawn above the lower and a plus sign is added to the DIMTP value if it is positive.
!DIMTSZ|Real|Drawing|0.0000
Specifies the size of oblique strokes drawn instead of arrowheads for linear, radius, and diameter dimensioning.\n\n  0\tDraws arrowheads.\n>0\tDraws oblique strokes instead of arrowheads. The size of the oblique strokes is determined by this value multiplied by the DIMSCALE value.
!DIMTVP|Real|Drawing|0.0000
Controls the vertical position of dimension text above or below the dimension line. AutoCAD uses the DIMTVP value when DIMTAD is off. The magnitude of the vertical offset of text is the product of the text height and DIMTVP. Setting DIMTVP to 1.0 is equivalent to setting DIMTAD to on. AutoCAD splits the dimension line to accommodate the text only if the absolute value of DIMTVP is less than 0.7.
!DIMTXSTY|String|Drawing|"STANDARD"
Specifies the text style of the dimension.
!DIMTXT|Real|Drawing|0.1800
Specifies the height of dimension text, unless the current text style has a fixed height.
!DIMTZIN|Integer|Drawing|0
Controls the suppression of zeros in tolerance values. DIMTZIN stores this value when you enter it on the command line or set it under Primary Units in the Annotation dialog box. DIMTZIN values 0-3 affect feet-and-inch dimensions only.\n\n0\tSuppresses zero feet and precisely zero inches\n1\tIncludes zero feet and precisely zero inches\n2\tIncludes zero feet and suppresses zero inches\n3\tIncludes zero inches and suppresses zero feet\n4\tSuppresses leading zeros in decimal dimensions (for example, 0.5000 becomes .5000)\n8\tSuppresses trailing zeros in decimal dimensions (for example, 12.5000 becomes 12.5)\n12\tSuppresses both leading and trailing zeros (for example, 0.5000 becomes 0.5)
!DIMUNIT|Integer|Drawing|2
Obsolete. Has no effect in AutoCAD 2000 except to preserve the integrity of pre-AutoCAD 2000 scripts and AutoLISP routines. In AutoCAD 2000, DIMUNIT is replaced by DIMLUNIT and DIMFRAC.
!DIMUPT|Switch|Drawing|Off
Controls options for user-positioned text.\n\nOff\tCursor controls only the dimension line location\nOn\tCursor controls both the text position and the dimension line location
!DIMZIN|Integer|Drawing|0
Controls the suppression of zeros in the primary unit value. DIMZIN stores this value when you enter it on the command line or set it under Primary Units in the Annotation dialog box. DIMZIN values 0-3 affect feet-and-inch dimensions only.\n\n0\tSuppresses zero feet and precisely zero inches\n1\tIncludes zero feet and precisely zero inches\n2\tIncludes zero feet and suppresses zero inches\n3\tIncludes zero inches and suppresses zero feet\n4\tSuppresses leading zeros in decimal dimensions (for example, 0.5000 becomes .5000)\n8\tSuppresses trailing zeros in decimal dimensions (for example, 12.5000 becomes 12.5)\n12\tSuppresses both leading and trailing zeros (for example, 0.5000 becomes 0.5)\n\nDIMZIN also affects real-to-string conversions performed by the AutoLISP rtos and angtos functions.
!DISPSILH|Integer|Drawing|0
Controls display of silhouette curves of solid objects in Wireframe mode. Also controls whether mesh is drawn or suppressed when a solid object is hidden.\n\n0\tOff\n1\tOn
#DISTANCE|Real|Not saved|0.0000
Stores the distance computed by the DIST command.
!DONUTID|Real|Not saved|0.5000
Sets the default for the inside diameter of a donut.
!DONUTOD|Real|Not saved|1.0000
Sets the default for the outside diameter of a donut. The value must be nonzero. If DONUTID is larger than DONUTOD, the two values are swapped by the next command.
!DRAGMODE|Integer|Registry|2
Controls the display of objects being dragged.\n\n0\tDoes not display an outline of the object as you drag it\n1\tDisplays the outline of the object as you drag it only if you enter drag on the command line after selecting the object to drag\n2\tAuto; always displays an outline of the object as you drag it
!DRAGP1|Integer|Registry|10
Sets the regen-drag input sampling rate.
!DRAGP2|Integer|Registry|25
Sets the fast-drag input sampling rate.
!DRAWORDERCTL|Integer|Drawing|3
Controls the draw order functionality when editting or inheriting from objects.\n\n0\tDisables draw order display until the drawing is reopened or a REGEN is completed.  Newly created objects do not inherit draw order from the original object.\n1\tDraw order display is retained after an object is editted.  Once the object is modified it will be displayed on screen at the correctly based on its original draw order.\n2\tDraw order for object inheritance is turned on. So an object will have the same draw oder that the original object had.\n3\tFull draw order functionality is provided for display and object inheritance.