system.mhs

microblaze下ucos移植源码

# ##############################################################################
# Created by Base System Builder Wizard for Xilinx EDK 10.1.01 Build EDK_K_SP1.3
# Thu Aug 07 12:37:16 2008
# Target Board:  Xilinx Virtex 4 ML403 Evaluation Platform Rev 1
# Family:    virtex4
# Device:    xc4vfx12
# Package:   ff668
# Speed Grade:  -10
# Processor: microblaze_0
# System clock frequency: 100.00 MHz
# On Chip Memory :  32 KB
# Total Off Chip Memory :   1 MB
# - SRAM =   1 MB
# ##############################################################################
 PARAMETER VERSION = 2.1.0


 PORT fpga_0_RS232_Uart_RX_pin = fpga_0_RS232_Uart_RX, DIR = I
 PORT fpga_0_RS232_Uart_TX_pin = fpga_0_RS232_Uart_TX, DIR = O
 PORT fpga_0_LEDs_4Bit_GPIO_IO_pin = fpga_0_LEDs_4Bit_GPIO_IO, DIR = IO, VEC = [0:3]
 PORT fpga_0_LEDs_Positions_GPIO_IO_pin = fpga_0_LEDs_Positions_GPIO_IO, DIR = IO, VEC = [0:4]
 PORT fpga_0_SRAM_Mem_A_pin = fpga_0_SRAM_Mem_A, DIR = O, VEC = [9:29]
 PORT fpga_0_SRAM_Mem_BEN_pin = fpga_0_SRAM_Mem_BEN, DIR = O, VEC = [0:3]
 PORT fpga_0_SRAM_Mem_WEN_pin = fpga_0_SRAM_Mem_WEN, DIR = O
 PORT fpga_0_SRAM_Mem_DQ_pin = fpga_0_SRAM_Mem_DQ, DIR = IO, VEC = [0:31]
 PORT fpga_0_SRAM_Mem_OEN_pin = fpga_0_SRAM_Mem_OEN, DIR = O, VEC = [0:0]
 PORT fpga_0_SRAM_Mem_CEN_pin = fpga_0_SRAM_Mem_CEN, DIR = O, VEC = [0:0]
 PORT fpga_0_SRAM_Mem_ADV_LDN_pin = fpga_0_SRAM_Mem_ADV_LDN, DIR = O
 PORT fpga_0_SRAM_CLOCK = sys_clk_s, DIR = O
 PORT sys_clk_pin = dcm_clk_s, DIR = I, SIGIS = CLK, CLK_FREQ = 100000000
 PORT sys_rst_pin = sys_rst_s, DIR = I, RST_POLARITY = 0, SIGIS = RST


BEGIN microblaze
 PARAMETER INSTANCE = microblaze_0
 PARAMETER C_INTERCONNECT = 1
 PARAMETER HW_VER = 7.10.d
 PARAMETER C_DEBUG_ENABLED = 1
 BUS_INTERFACE DLMB = dlmb
 BUS_INTERFACE ILMB = ilmb
 BUS_INTERFACE DPLB = mb_plb
 BUS_INTERFACE IPLB = mb_plb
 BUS_INTERFACE DEBUG = microblaze_0_dbg
 PORT MB_RESET = mb_reset
 PORT Interrupt = Interrupt
END

BEGIN plb_v46
 PARAMETER INSTANCE = mb_plb
 PARAMETER HW_VER = 1.03.a
 PORT PLB_Clk = sys_clk_s
 PORT SYS_Rst = sys_bus_reset
END

BEGIN lmb_v10
 PARAMETER INSTANCE = ilmb
 PARAMETER HW_VER = 1.00.a
 PORT LMB_Clk = sys_clk_s
 PORT SYS_Rst = sys_bus_reset
END

BEGIN lmb_v10
 PARAMETER INSTANCE = dlmb
 PARAMETER HW_VER = 1.00.a
 PORT LMB_Clk = sys_clk_s
 PORT SYS_Rst = sys_bus_reset
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = dlmb_cntlr
 PARAMETER HW_VER = 2.10.a
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x00007fff
 BUS_INTERFACE SLMB = dlmb
 BUS_INTERFACE BRAM_PORT = dlmb_port
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = ilmb_cntlr
 PARAMETER HW_VER = 2.10.a
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x00007fff
 BUS_INTERFACE SLMB = ilmb
 BUS_INTERFACE BRAM_PORT = ilmb_port
END

BEGIN bram_block
 PARAMETER INSTANCE = lmb_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = ilmb_port
 BUS_INTERFACE PORTB = dlmb_port
END

BEGIN xps_uartlite
 PARAMETER INSTANCE = RS232_Uart
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_BAUDRATE = 9600
 PARAMETER C_DATA_BITS = 8
 PARAMETER C_ODD_PARITY = 0
 PARAMETER C_USE_PARITY = 0
 PARAMETER C_SPLB_CLK_FREQ_HZ = 100000000
 PARAMETER C_BASEADDR = 0x84000000
 PARAMETER C_HIGHADDR = 0x8400ffff
 BUS_INTERFACE SPLB = mb_plb
 PORT RX = fpga_0_RS232_Uart_RX
 PORT TX = fpga_0_RS232_Uart_TX
END

BEGIN xps_gpio
 PARAMETER INSTANCE = LEDs_4Bit
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_GPIO_WIDTH = 4
 PARAMETER C_IS_DUAL = 0
 PARAMETER C_IS_BIDIR = 1
 PARAMETER C_ALL_INPUTS = 0
 PARAMETER C_BASEADDR = 0x81400000
 PARAMETER C_HIGHADDR = 0x8140ffff
 BUS_INTERFACE SPLB = mb_plb
 PORT GPIO_IO = fpga_0_LEDs_4Bit_GPIO_IO
END

BEGIN xps_gpio
 PARAMETER INSTANCE = LEDs_Positions
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_GPIO_WIDTH = 5
 PARAMETER C_IS_DUAL = 0
 PARAMETER C_IS_BIDIR = 1
 PARAMETER C_ALL_INPUTS = 0
 PARAMETER C_BASEADDR = 0x81420000
 PARAMETER C_HIGHADDR = 0x8142ffff
 BUS_INTERFACE SPLB = mb_plb
 PORT GPIO_IO = fpga_0_LEDs_Positions_GPIO_IO
END

BEGIN xps_mch_emc
 PARAMETER INSTANCE = SRAM
 PARAMETER HW_VER = 1.01.a
 PARAMETER C_MCH_PLB_CLK_PERIOD_PS = 10000
 PARAMETER C_NUM_BANKS_MEM = 1
 PARAMETER C_MAX_MEM_WIDTH = 32
 PARAMETER C_INCLUDE_NEGEDGE_IOREGS = 1
 PARAMETER C_INCLUDE_DATAWIDTH_MATCHING_0 = 1
 PARAMETER C_MEM0_WIDTH = 32
 PARAMETER C_SYNCH_MEM_0 = 1
 PARAMETER C_TCEDV_PS_MEM_0 = 0
 PARAMETER C_TWC_PS_MEM_0 = 0
 PARAMETER C_TAVDV_PS_MEM_0 = 0
 PARAMETER C_TWP_PS_MEM_0 = 0
 PARAMETER C_THZCE_PS_MEM_0 = 0
 PARAMETER C_TLZWE_PS_MEM_0 = 0
 PARAMETER C_MEM0_BASEADDR = 0x84100000
 PARAMETER C_MEM0_HIGHADDR = 0x841fffff
 BUS_INTERFACE SPLB = mb_plb
 PORT Mem_A = fpga_0_SRAM_Mem_A_split
 PORT Mem_BEN = fpga_0_SRAM_Mem_BEN
 PORT Mem_WEN = fpga_0_SRAM_Mem_WEN
 PORT Mem_DQ = fpga_0_SRAM_Mem_DQ
 PORT Mem_OEN = fpga_0_SRAM_Mem_OEN
 PORT Mem_CEN = fpga_0_SRAM_Mem_CEN
 PORT Mem_ADV_LDN = fpga_0_SRAM_Mem_ADV_LDN
 PORT RdClk = sys_clk_s
END

BEGIN xps_timer
 PARAMETER INSTANCE = xps_timer_1
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_COUNT_WIDTH = 32
 PARAMETER C_ONE_TIMER_ONLY = 1
 PARAMETER C_BASEADDR = 0x83c00000
 PARAMETER C_HIGHADDR = 0x83c0ffff
 BUS_INTERFACE SPLB = mb_plb
 PORT Interrupt = xps_timer_1_Interrupt
END

BEGIN util_bus_split
 PARAMETER INSTANCE = SRAM_util_bus_split_0
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_SIZE_IN = 32
 PARAMETER C_LEFT_POS = 9
 PARAMETER C_SPLIT = 30
 PORT Sig = fpga_0_SRAM_Mem_A_split
 PORT Out1 = fpga_0_SRAM_Mem_A
END

BEGIN clock_generator
 PARAMETER INSTANCE = clock_generator_0
 PARAMETER HW_VER = 2.01.a
 PARAMETER C_EXT_RESET_HIGH = 1
 PARAMETER C_CLKIN_FREQ = 100000000
 PARAMETER C_CLKOUT0_FREQ = 100000000
 PARAMETER C_CLKOUT0_BUF = TRUE
 PARAMETER C_CLKOUT0_PHASE = 0
 PARAMETER C_CLKOUT0_GROUP = NONE
 PORT CLKOUT0 = sys_clk_s
 PORT CLKIN = dcm_clk_s
 PORT LOCKED = Dcm_all_locked
 PORT RST = net_gnd
END

BEGIN mdm
 PARAMETER INSTANCE = debug_module
 PARAMETER HW_VER = 1.00.d
 PARAMETER C_MB_DBG_PORTS = 1
 PARAMETER C_USE_UART = 1
 PARAMETER C_UART_WIDTH = 8
 PARAMETER C_BASEADDR = 0x84400000
 PARAMETER C_HIGHADDR = 0x8440ffff
 BUS_INTERFACE SPLB = mb_plb
 BUS_INTERFACE MBDEBUG_0 = microblaze_0_dbg
 PORT Debug_SYS_Rst = Debug_SYS_Rst
END

BEGIN proc_sys_reset
 PARAMETER INSTANCE = proc_sys_reset_0
 PARAMETER HW_VER = 2.00.a
 PARAMETER C_EXT_RESET_HIGH = 0
 PORT Slowest_sync_clk = sys_clk_s
 PORT Dcm_locked = Dcm_all_locked
 PORT Ext_Reset_In = sys_rst_s
 PORT MB_Reset = mb_reset
 PORT Bus_Struct_Reset = sys_bus_reset
 PORT MB_Debug_Sys_Rst = Debug_SYS_Rst
 PORT Peripheral_Reset = sys_periph_reset
END

BEGIN xps_intc
 PARAMETER INSTANCE = xps_intc_0
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_BASEADDR = 0x81800000
 PARAMETER C_HIGHADDR = 0x8180ffff
 BUS_INTERFACE SPLB = mb_plb
 PORT Irq = Interrupt
 PORT Intr = xps_timer_1_Interrupt
END