xlcd.h.bak

ucos-ii在PIC18F4520上的移植

#ifndef __XLCD_H
#define __XLCD_H

/* PIC18 XLCD peripheral routines.
*
*  >>>>>>>>>>> MODIFIED BY Hxk
*
*   Notes:
*      - These libraries routines are written to support the
*        Hitachi HD44780 LCD controller.
*      - The user must define the following items:
*          - The LCD interface type (4- or 8-bits)
*          - If 4-bit mode
*              - whether using the upper or lower nibble
*          - The data port
*              - The tris register for data port
*              - The control signal ports and pins
*              - The control signal port tris and pins
*          - The user must provide three delay routines:
*              - DelayFor18TCY() provides a 18 Tcy delay
*              - DelayPORXLCD() provides at least 15ms delay
*              - DelayXLCD() provides at least 5ms delay
*/

/* Interface type 8-bit or 4-bit
* For 8-bit operation uncomment the #define BIT8
*/
/* #define BIT8 */

/* When in 4-bit interface define if the data is in the upper
* or lower nibble.  For lower nibble, comment the #define UPPER
*/
/* #define UPPER 

/* DATA_PORT defines the port to which the LCD data lines are connected */

#define DATA_PORT      PORTB
#define TRIS_DATA_PORT TRISB

/* CTRL_PORT defines the port where the control lines are connected.
* These are just samples, change to match your application.
*/

//#define RW_PIN   PORTCbits.RC1   /* PORT for RW */
//#define TRIS_RW  DDRCbits.RC1    /* TRIS for RW */
//#define RS_PIN   PORTCbits.RC0   /* PORT for RS */
//#define TRIS_RS  DDRCbits.RC0    /* TRIS for RS */
//#define E_PIN    PORTCbits.RC2   /* PORT for E  */
//#define TRIS_E   DDRCbits.RC2    /* TRIS for E  */

#define RW_PIN   PORTCbits.RC3   /* PORT for RW */
#define TRIS_RW  DDRCbits.RC3    /* TRIS for RW */
#define RS_PIN   PORTCbits.RC2   /* PORT for RS */
#define TRIS_RS  DDRCbits.RC2    /* TRIS for RS */
#define E_PIN    PORTCbits.RC4   /* PORT for E  */
#define TRIS_E   DDRCbits.RC4    /* TRIS for E  */

/* Display ON/OFF Control defines */
#define DON         0b00001111  /* Display on      */
#define DOFF        0b00001011  /* Display off     */
#define CURSOR_ON   0b00001111  /* Cursor on       */
#define CURSOR_OFF  0b00001101  /* Cursor off      */
#define BLINK_ON    0b00001111  /* Cursor Blink    */
#define BLINK_OFF   0b00001110  /* Cursor No Blink */

/* Cursor or Display Shift defines */
#define SHIFT_CUR_LEFT    0b00010011  /* Cursor shifts to the left   */
#define SHIFT_CUR_RIGHT   0b00010111  /* Cursor shifts to the right  */
#define SHIFT_DISP_LEFT   0b00011011  /* Display shifts to the left  */
#define SHIFT_DISP_RIGHT  0b00011111  /* Display shifts to the right */

/* Function Set defines */
#define FOUR_BIT   0b00101111  /* 4-bit Interface               */
#define EIGHT_BIT  0b00111111  /* 8-bit Interface               */
#define LINE_5X7   0b00110011  /* 5x7 characters, single line   */
#define LINE_5X10  0b00110111  /* 5x10 characters               */
#define LINES_5X7  0b00111011  /* 5x7 characters, multiple line */
#define LINES_FLIP 0b00111100  /* mirror-invert the second line */

/* Entry mode defines */
#define ENTRY_CURSOR_DEC  		0b00000101	/* Sets the cursor move direction to decrement	*/
#define ENTRY_CURSOR_INC		0b00000111	/* Sets the cursor move direction to increment	*/
#define ENTRY_DISPLAY_SHIFT		0b00000111 	/* Sets the display to shift					*/
#define ENTRY_DISPLAY_NO_SHIFT  0b00000110	/* Sets the display to not shift				*/

#define PARAM_SCLASS auto
#define MEM_MODEL far  /* Change this to near for small memory model */

/* OpenXLCD
* Configures I/O pins for external LCD
*/
void OpenXLCD(PARAM_SCLASS unsigned char);

/* SetCGRamAddr
* Sets the character generator address
*/
void SetCGRamAddr(PARAM_SCLASS unsigned char);

/* SetDDRamAddr
* Sets the display data address
*/
void SetDDRamAddr(PARAM_SCLASS unsigned char);

/* BusyXLCD
* Returns the busy status of the LCD
*/
unsigned char BusyXLCD(void);

/* ReadAddrXLCD
* Reads the current address
*/
unsigned char ReadAddrXLCD(void);

/* ReadDataXLCD
* Reads a byte of data
*/
char ReadDataXLCD(void);

/* WriteCmdXLCD
* Writes a command to the LCD
*/
void WriteCmdXLCD(PARAM_SCLASS unsigned char);

/* WriteDataXLCD
* Writes a data byte to the LCD
*/
void WriteDataXLCD(PARAM_SCLASS char);

/* putcXLCD
* A putc is a write
*/
#define putcXLCD WriteDataXLCD

/* putsXLCD
* Writes a string of characters to the LCD
*/
void putsXLCD(PARAM_SCLASS char *);

/* putrsXLCD
* Writes a string of characters in ROM to the LCD
*/
void putrsXLCD(PARAM_SCLASS const MEM_MODEL rom char *);

/* User defines these routines according to the oscillator frequency */
extern void DelayFor18TCY(void);
extern void DelayPORXLCD(void);
extern void DelayXLCD(void);

#endif