main.c

了解点阵液晶显示实验的工作原理掌握点阵液晶显示实验程序的设计方法.本实验板中使用的是内置12864A 的液晶屏12864A 由两片带控制器的列驱动电路 KS0108 和一片行驱动电路KS0107 组

#include "c8051f020.h"  
#include <intrins.h>              

/*void Delay1us(unsigned char us)
{
	while (us)
	{
	  _nop_(); _nop_(); _nop_(); _nop_(); _nop_();
	  --us;
	}
}*/
void SYSCLK_Init (void)
{
   int i;                              // delay counter
   OSCXCN = 0x67;                      // start external oscillator with
                                       // 18.432MHz crystal
   for (i=0; i < 256; i++) ;           // Wait for osc. to start up
   while (!(OSCXCN & 0x80)) ;          // Wait for crystal osc. to settle
   OSCICN = 0x88;                      // select external oscillator as SYSCLK
                                       // source and enable missing clock
                                       // detector
//	OSCICN = 0x07;   //interal 16MHZ
}

#define PRT0CF P0MDOUT
#define PRT1CF P1MDOUT
#define PRT2CF P2MDOUT

void PORT_Init (void)
{
   XBR0    = 0x07;                     // Enable SMBus, SPI0, and UART0
   XBR1    = 0x00;
   XBR2    = 0x44;                     // Enable crossbar and weak pull-ups
   EMI0CF  = 0x27;
   EMI0TC  = 0x21;
   P74OUT  = 0xFF;
   P0MDOUT = 0x15;

   P1MDOUT |= 0x3C;  					//P1.2-P1.5推挽输出
   P1 &= 0xc3;							//P1.2-P1.5=0
}

void SPI0_Init (void)
{
   SPI0CFG = 0x07;                     // data sampled on 1st SCK rising edge
                                       // 8-bit data words
   SPI0CFG|=0xC0;	//CKPOL =1;

   SPI0CN = 0x03;                      // Master mode; SPI enabled; flags
                                       // cleared
   SPI0CKR = SYSCLK/2/8000000-1;       // SPI clock <= 8MHz (limited by 
                                       // EEPROM spec.)
}

unsigned char Count1ms;
void Timer0_Init (void)
{
   	CKCON|=0x8;
   	TMOD|=0x1;    	//16Bit
	Count1ms=10;
   	TR0 = 0;                         	// STOP Timer0
   	TH0 = (-SYSCLK/1000) >> 8;    		// set Timer0 to overflow in 1ms
   	TL0 = -SYSCLK/1000;
   	TR0 = 1;   	// START Timer0
   	IE|= 0x2; 
}

void Timer0_ISR (void) interrupt 1  //1ms
{
	TH0 = (-SYSCLK/1000) >> 8;  
   	TL0 = -SYSCLK/1000;
	if (Count1ms) Count1ms--;
}

void Delay1ms(unsigned char T)
{
	Count1ms=T;
	while (Count1ms);
}

void Delay1s(unsigned char T)
{
	while (T)
	{
		Delay1ms(200);
		Delay1ms(200);
		Delay1ms(200);
		Delay1ms(200);
		Delay1ms(200);
		T--;
	}
}

//void Test7279(bit LoopFlag);
void TestLCD(void);
//void DispLED(char *buf);
void main (void) 
{
	WDTCN = 0xde;
	WDTCN = 0xad;           //关看门狗
	SYSCLK_Init ();         //初始化时钟
	Timer0_Init();			//初始化定时器
	PORT_Init ();           //初始化IO口
	SPI0_Init ();           //初始化SPI0

	CPT1CN|=0x80;	//使能比较器1
	REF0CN = 0x03;  //使能片内参考电压
	DAC0CN |= 0x80;	//使能DAC0
	DAC0H=0;	DAC0L=0;

	EA=1;					//开中断

	//Test7279(0);
 	TestLCD();

}