📄 startup.s
字号:
#/***********************************************************************/
#/* This file is part of the uVision/ARM development tools */
#/* Copyright KEIL ELEKTRONIK GmbH 2002-2004 */
#/***********************************************************************/
#/* */
#/* STARTUP.S: Startup file */
#/* */
#/***********************************************************************/
/*
//*** <<< Use Configuration Wizard in Context Menu >>> ***
*/
# *** Startup Code (executed after Reset) ***
# Standard definitions of Mode bits and Interrupt (I & F) flags in PSRs
.equ Mode_USR, 0x10
.equ Mode_FIQ, 0x11
.equ Mode_IRQ, 0x12
.equ Mode_SVC, 0x13
.equ Mode_ABT, 0x17
.equ Mode_UND, 0x1B
.equ Mode_SYS, 0x1F
.equ I_Bit, 0x80 /* when I bit is set, IRQ is disabled */
.equ F_Bit, 0x40 /* when F bit is set, FIQ is disabled */
/*
// <h> Stack Configuration
// <o> Top of Stack Address <0x0-0xFFFFFFFF:4>
// <h> Stack Sizes (in Bytes)
// <o1> Undefined Mode <0x0-0xFFFFFFFF:4>
// <o2> Supervisor Mode <0x0-0xFFFFFFFF:4>
// <o3> Abort Mode <0x0-0xFFFFFFFF:4>
// <o4> Fast Interrupt Mode <0x0-0xFFFFFFFF:4>
// <o5> Interrupt Mode <0x0-0xFFFFFFFF:4>
// <o6> User/System Mode <0x0-0xFFFFFFFF:4>
// </h>
// </h>
*/
.equ Top_Stack, 0x40004000
.equ UND_Stack_Size, 0x00000004
.equ SVC_Stack_Size, 0x00000004
.equ ABT_Stack_Size, 0x00000004
.equ FIQ_Stack_Size, 0x00000004
.equ IRQ_Stack_Size, 0x00000080
.equ USR_Stack_Size, 0x00000400
# VPBDIV definitions
.equ VPBDIV, 0xE01FC100 /* VPBDIV Address */
/*
// <e> VPBDIV Setup
// <i> Peripheral Bus Clock Rate
// <o1.0..1> VPBDIV: VPB Clock
// <0=> VPB Clock = CPU Clock / 4
// <1=> VPB Clock = CPU Clock
// <2=> VPB Clock = CPU Clock / 2
// <o1.4..5> XCLKDIV: XCLK Pin
// <0=> XCLK Pin = CPU Clock / 4
// <1=> XCLK Pin = CPU Clock
// <2=> XCLK Pin = CPU Clock / 2
// </e>
*/
.equ VPBDIV_SETUP, 0
.equ VPBDIV_Val, 0x00000000
# Phase Locked Loop (PLL) definitions
.equ PLL_BASE, 0xE01FC080 /* PLL Base Address */
.equ PLLCON_OFS, 0x00 /* PLL Control Offset*/
.equ PLLCFG_OFS, 0x04 /* PLL Configuration Offset */
.equ PLLSTAT_OFS, 0x08 /* PLL Status Offset */
.equ PLLFEED_OFS, 0x0C /* PLL Feed Offset */
.equ PLLCON_PLLE, (1<<0) /* PLL Enable */
.equ PLLCON_PLLC, (1<<1) /* PLL Connect */
.equ PLLCFG_MSEL, (0x1F<<0) /* PLL Multiplier */
.equ PLLCFG_PSEL, (0x03<<5) /* PLL Divider */
.equ PLLSTAT_PLOCK, (1<<10) /* PLL Lock Status */
/*
// <e> PLL Setup
// <o1.0..4> MSEL: PLL Multiplier Selection
// <1-32><#-1>
// <i> M Value
// <o1.5..6> PSEL: PLL Divider Selection
// <0=> 1 <1=> 2 <2=> 4 <3=> 8
// <i> P Value
// </e>
*/
.equ PLL_SETUP, 0
.equ PLLCFG_Val, 0x00000024
# Memory Accelerator Module (MAM) definitions
.equ MAM_BASE, 0xE01FC000 /* MAM Base Address */
.equ MAMCR_OFS, 0x00 /* MAM Control Offset*/
.equ MAMTIM_OFS, 0x04 /* MAM Timing Offset */
/*
// <e> MAM Setup
// <o1.0..1> MAM Control
// <0=> Disabled
// <1=> Partially Enabled
// <2=> Fully Enabled
// <i> Mode
// <o2.0..2> MAM Timing
// <0=> Reserved <1=> 1 <2=> 2 <3=> 3
// <4=> 4 <5=> 5 <6=> 6 <7=> 7
// <i> Fetch Cycles
// </e>
*/
.equ MAM_SETUP, 1
.equ MAMCR_Val, 0x00000002
.equ MAMTIM_Val, 0x00000004
# External Memory Controller (EMC) definitions
.equ EMC_BASE, 0xFFE00000 /* EMC Base Address */
.equ BCFG0_OFS, 0x00 /* BCFG0 Offset */
.equ BCFG1_OFS, 0x04 /* BCFG1 Offset */
.equ BCFG2_OFS, 0x08 /* BCFG2 Offset */
.equ BCFG3_OFS, 0x0C /* BCFG3 Offset */
/*
// <e> External Memory Controller (EMC)
*/
.equ EMC_SETUP, 0
/*
// <e> Bank Configuration 0 (BCFG0)
// <o1.0..3> IDCY: Idle Cycles <0-15>
// <o1.5..9> WST1: Wait States 1 <0-31>
// <o1.11..15> WST2: Wait States 2 <0-31>
// <o1.10> RBLE: Read Byte Lane Enable
// <o1.26> WP: Write Protect
// <o1.27> BM: Burst ROM
// <o1.28..29> MW: Memory Width <0=> 8-bit <1=> 16-bit
// <2=> 32-bit <3=> Reserved
// </e>
*/
.equ BCFG0_SETUP, 0
.equ BCFG0_Val, 0x0000FBEF
/*
// <e> Bank Configuration 1 (BCFG1)
// <o1.0..3> IDCY: Idle Cycles <0-15>
// <o1.5..9> WST1: Wait States 1 <0-31>
// <o1.11..15> WST2: Wait States 2 <0-31>
// <o1.10> RBLE: Read Byte Lane Enable
// <o1.26> WP: Write Protect
// <o1.27> BM: Burst ROM
// <o1.28..29> MW: Memory Width <0=> 8-bit <1=> 16-bit
// <2=> 32-bit <3=> Reserved
// </e>
*/
.equ BCFG1_SETUP, 0
.equ BCFG1_Val, 0x0000FBEF
/*
// <e> Bank Configuration 2 (BCFG2)
// <o1.0..3> IDCY: Idle Cycles <0-15>
// <o1.5..9> WST1: Wait States 1 <0-31>
// <o1.11..15> WST2: Wait States 2 <0-31>
// <o1.10> RBLE: Read Byte Lane Enable
// <o1.26> WP: Write Protect
// <o1.27> BM: Burst ROM
// <o1.28..29> MW: Memory Width <0=> 8-bit <1=> 16-bit
// <2=> 32-bit <3=> Reserved
// </e>
*/
.equ BCFG2_SETUP, 0
.equ BCFG2_Val, 0x0000FBEF
/*
// <e> Bank Configuration 3 (BCFG3)
// <o1.0..3> IDCY: Idle Cycles <0-15>
// <o1.5..9> WST1: Wait States 1 <0-31>
// <o1.11..15> WST2: Wait States 2 <0-31>
// <o1.10> RBLE: Read Byte Lane Enable
// <o1.26> WP: Write Protect
// <o1.27> BM: Burst ROM
// <o1.28..29> MW: Memory Width <0=> 8-bit <1=> 16-bit
// <2=> 32-bit <3=> Reserved
// </e>
*/
.equ BCFG3_SETUP, 0
.equ BCFG3_Val, 0x0000FBEF
/*
// </e> End of EMC
*/
# External Memory Pins definitions
.equ PINSEL2, 0xE002C014 /* PINSEL2 Address */
.equ PINSEL2_Val, 0x0E6149E4 /* CS0..3, OE, WE, BLS0..3,
D0..31, A2..23, JTAG Pins */
# Starupt Code must be linked first at Address at which it expects to run.
.text
.arm
.global _startup
.func _startup
_startup:
# Exception Vectors
# Mapped to Address 0.
# Absolute addressing mode must be used.
# Dummy Handlers are implemented as infinite loops which can be modified.
Vectors: LDR PC, Reset_Addr
LDR PC, Undef_Addr
LDR PC, SWI_Addr
LDR PC, PAbt_Addr
LDR PC, DAbt_Addr
NOP /* Reserved Vector */
# LDR PC, IRQ_Addr
LDR PC, [PC, #-0x0FF0] /* Vector from VicVectAddr */
LDR PC, FIQ_Addr
Reset_Addr: .word Reset_Handler
Undef_Addr: .word Undef_Handler
SWI_Addr: .word SWI_Handler
PAbt_Addr: .word PAbt_Handler
DAbt_Addr: .word DAbt_Handler
.word 0 /* Reserved Address */
IRQ_Addr: .word IRQ_Handler
FIQ_Addr: .word FIQ_Handler
Undef_Handler: B Undef_Handler
SWI_Handler: B SWI_Handler
PAbt_Handler: B PAbt_Handler
DAbt_Handler: B DAbt_Handler
IRQ_Handler: B IRQ_Handler
FIQ_Handler: B FIQ_Handler
# Reset Handler
Reset_Handler:
.ifdef EXTERNAL_MODE
LDR R0, =PINSEL2
LDR R1, =PINSEL2_Val
STR R1, [R0]
.endif
.if EMC_SETUP
LDR R0, =EMC_BASE
.if BCFG0_SETUP
LDR R1, =BCFG0_Val
STR R1, [R0, #BCFG0_OFS]
.endif
.if BCFG1_SETUP
LDR R1, =BCFG1_Val
STR R1, [R0, #BCFG1_OFS]
.endif
.if BCFG2_SETUP
LDR R1, =BCFG2_Val
STR R1, [R0, #BCFG2_OFS]
.endif
.if BCFG3_SETUP
LDR R1, =BCFG3_Val
STR R1, [R0, #BCFG3_OFS]
.endif
.endif
.if VPBDIV_SETUP
LDR R0, =VPBDIV
LDR R1, =VPBDIV_Val
STR R1, [R0]
.endif
.if PLL_SETUP
LDR R0, =PLL_BASE
MOV R1, #0xAA
MOV R2, #0x55
# Configure and Enable PLL
MOV R3, #PLLCFG_Val
STR R3, [R0, #PLLCFG_OFS]
MOV R3, #PLLCON_PLLE
STR R3, [R0, #PLLCON_OFS]
STR R1, [R0, #PLLFEED_OFS]
STR R2, [R0, #PLLFEED_OFS]
# Wait until PLL Locked
PLL_Loop: LDR R3, [R0, #PLLSTAT_OFS]
ANDS R3, R3, #PLLSTAT_PLOCK
BEQ PLL_Loop
# Switch to PLL Clock
MOV R3, #(PLLCON_PLLE | PLLCON_PLLC)
STR R3, [R0, #PLLCON_OFS]
STR R1, [R0, #PLLFEED_OFS]
STR R2, [R0, #PLLFEED_OFS]
.endif
.if MAM_SETUP
LDR R0, =MAM_BASE
MOV R1, #MAMTIM_Val
STR R1, [R0, #MAMTIM_OFS]
MOV R1, #MAMCR_Val
STR R1, [R0, #MAMCR_OFS]
.endif
# Memory Mapping (when Interrupt Vectors are in RAM)
.equ MEMMAP, 0xE01FC040 /* Memory Mapping Control */
.ifdef RAM_INTVEC
LDR R0, =MEMMAP
MOV R1, #2
STR R1, [R0]
.endif
# Initialise Interrupt System
# ...
# Setup Stack for each mode
LDR R0, =Top_Stack
# Enter Undefined Instruction Mode and set its Stack Pointer
MSR CPSR_c, #Mode_UND|I_Bit|F_Bit
MOV SP, R0
SUB R0, R0, #UND_Stack_Size
# Enter Abort Mode and set its Stack Pointer
MSR CPSR_c, #Mode_ABT|I_Bit|F_Bit
MOV SP, R0
SUB R0, R0, #ABT_Stack_Size
# Enter FIQ Mode and set its Stack Pointer
MSR CPSR_c, #Mode_FIQ|I_Bit|F_Bit
MOV SP, R0
SUB R0, R0, #FIQ_Stack_Size
# Enter IRQ Mode and set its Stack Pointer
MSR CPSR_c, #Mode_IRQ|I_Bit|F_Bit
MOV SP, R0
SUB R0, R0, #IRQ_Stack_Size
# Enter Supervisor Mode and set its Stack Pointer
MSR CPSR_c, #Mode_SVC|I_Bit|F_Bit
MOV SP, R0
SUB R0, R0, #SVC_Stack_Size
# Enter User Mode and set its Stack Pointer
MSR CPSR_c, #Mode_USR
MOV SP, R0
# Setup a default Stack Limit (when compiled with "-mapcs-stack-check")
SUB SL, SP, #USR_Stack_Size
# Relocate .data section (Copy from ROM to RAM)
LDR R1, =_etext
LDR R2, =_data
LDR R3, =_edata
LoopRel: CMP R2, R3
LDRLO R0, [R1], #4
STRLO R0, [R2], #4
BLO LoopRel
# Clear .bss section (Zero init)
MOV R0, #0
LDR R1, =__bss_start__
LDR R2, =__bss_end__
LoopZI: CMP R1, R2
STRLO R0, [R1], #4
BLO LoopZI
# Enter the C code
B _start
.size _startup, . - _startup
.endfunc
.end
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -