ne2k-pci.c

linux和2410结合开发 用他可以生成2410所需的zImage文件

		printk (KERN_ERR "ne2kpci(%s): unable to get memory for dev->priv.\n",
			pdev->slot_name);
		goto err_out_free_netdev;
	}

	ei_status.name = pci_clone_list[chip_idx].name;
	ei_status.tx_start_page = start_page;
	ei_status.stop_page = stop_page;
	ei_status.word16 = 1;
	ei_status.ne2k_flags = flags;
	if (fnd_cnt < MAX_UNITS) {
		if (full_duplex[fnd_cnt] > 0  ||  (options[fnd_cnt] & FORCE_FDX))
			ei_status.ne2k_flags |= FORCE_FDX;
	}

	ei_status.rx_start_page = start_page + TX_PAGES;
#ifdef PACKETBUF_MEMSIZE
	/* Allow the packet buffer size to be overridden by know-it-alls. */
	ei_status.stop_page = ei_status.tx_start_page + PACKETBUF_MEMSIZE;
#endif

	ei_status.reset_8390 = &ne2k_pci_reset_8390;
	ei_status.block_input = &ne2k_pci_block_input;
	ei_status.block_output = &ne2k_pci_block_output;
	ei_status.get_8390_hdr = &ne2k_pci_get_8390_hdr;
	ei_status.priv = (unsigned long) pdev;
	dev->open = &ne2k_pci_open;
	dev->stop = &ne2k_pci_close;
	dev->do_ioctl = &netdev_ioctl;
	NS8390_init(dev, 0);

	i = register_netdev(dev);
	if (i)
		goto err_out_free_8390;

	printk("%s: %s found at %#lx, IRQ %d, ",
		   dev->name, pci_clone_list[chip_idx].name, ioaddr, dev->irq);
	for(i = 0; i < 6; i++) {
		printk("%2.2X%s", SA_prom[i], i == 5 ? ".\n": ":");
		dev->dev_addr[i] = SA_prom[i];
	}

	return 0;

err_out_free_8390:
	kfree(dev->priv);
err_out_free_netdev:
	kfree (dev);
err_out_free_res:
	release_region (ioaddr, NE_IO_EXTENT);
	pci_set_drvdata (pdev, NULL);
	return -ENODEV;

}

static int ne2k_pci_open(struct net_device *dev)
{
	int ret = request_irq(dev->irq, ei_interrupt, SA_SHIRQ, dev->name, dev);
	if (ret)
		return ret;

	/* Set full duplex for the chips that we know about. */
	if (ei_status.ne2k_flags & FORCE_FDX) {
		long ioaddr = dev->base_addr;
		if (ei_status.ne2k_flags & REALTEK_FDX) {
			outb(0xC0 + E8390_NODMA, ioaddr + NE_CMD); /* Page 3 */
			outb(inb(ioaddr + 0x20) | 0x80, ioaddr + 0x20);
		} else if (ei_status.ne2k_flags & HOLTEK_FDX)
			outb(inb(ioaddr + 0x20) | 0x80, ioaddr + 0x20);
	}
	ei_open(dev);
	return 0;
}

static int ne2k_pci_close(struct net_device *dev)
{
	ei_close(dev);
	free_irq(dev->irq, dev);
	return 0;
}

/* Hard reset the card.  This used to pause for the same period that a
   8390 reset command required, but that shouldn't be necessary. */
static void ne2k_pci_reset_8390(struct net_device *dev)
{
	unsigned long reset_start_time = jiffies;

	if (debug > 1) printk("%s: Resetting the 8390 t=%ld...",
						  dev->name, jiffies);

	outb(inb(NE_BASE + NE_RESET), NE_BASE + NE_RESET);

	ei_status.txing = 0;
	ei_status.dmaing = 0;

	/* This check _should_not_ be necessary, omit eventually. */
	while ((inb(NE_BASE+EN0_ISR) & ENISR_RESET) == 0)
		if (jiffies - reset_start_time > 2) {
			printk("%s: ne2k_pci_reset_8390() did not complete.\n", dev->name);
			break;
		}
	outb(ENISR_RESET, NE_BASE + EN0_ISR);	/* Ack intr. */
}

/* Grab the 8390 specific header. Similar to the block_input routine, but
   we don't need to be concerned with ring wrap as the header will be at
   the start of a page, so we optimize accordingly. */

static void ne2k_pci_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page)
{

	long nic_base = dev->base_addr;

	/* This *shouldn't* happen. If it does, it's the last thing you'll see */
	if (ei_status.dmaing) {
		printk("%s: DMAing conflict in ne2k_pci_get_8390_hdr "
			   "[DMAstat:%d][irqlock:%d].\n",
			   dev->name, ei_status.dmaing, ei_status.irqlock);
		return;
	}

	ei_status.dmaing |= 0x01;
	outb(E8390_NODMA+E8390_PAGE0+E8390_START, nic_base+ NE_CMD);
	outb(sizeof(struct e8390_pkt_hdr), nic_base + EN0_RCNTLO);
	outb(0, nic_base + EN0_RCNTHI);
	outb(0, nic_base + EN0_RSARLO);		/* On page boundary */
	outb(ring_page, nic_base + EN0_RSARHI);
	outb(E8390_RREAD+E8390_START, nic_base + NE_CMD);

	if (ei_status.ne2k_flags & ONLY_16BIT_IO) {
		insw(NE_BASE + NE_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr)>>1);
	} else {
		*(u32*)hdr = le32_to_cpu(inl(NE_BASE + NE_DATAPORT));
		le16_to_cpus(&hdr->count);
	}

	outb(ENISR_RDC, nic_base + EN0_ISR);	/* Ack intr. */
	ei_status.dmaing &= ~0x01;
}

/* Block input and output, similar to the Crynwr packet driver.  If you
   are porting to a new ethercard, look at the packet driver source for hints.
   The NEx000 doesn't share the on-board packet memory -- you have to put
   the packet out through the "remote DMA" dataport using outb. */

static void ne2k_pci_block_input(struct net_device *dev, int count,
				 struct sk_buff *skb, int ring_offset)
{
	long nic_base = dev->base_addr;
	char *buf = skb->data;

	/* This *shouldn't* happen. If it does, it's the last thing you'll see */
	if (ei_status.dmaing) {
		printk("%s: DMAing conflict in ne2k_pci_block_input "
			   "[DMAstat:%d][irqlock:%d].\n",
			   dev->name, ei_status.dmaing, ei_status.irqlock);
		return;
	}
	ei_status.dmaing |= 0x01;
	if (ei_status.ne2k_flags & ONLY_32BIT_IO)
		count = (count + 3) & 0xFFFC;
	outb(E8390_NODMA+E8390_PAGE0+E8390_START, nic_base+ NE_CMD);
	outb(count & 0xff, nic_base + EN0_RCNTLO);
	outb(count >> 8, nic_base + EN0_RCNTHI);
	outb(ring_offset & 0xff, nic_base + EN0_RSARLO);
	outb(ring_offset >> 8, nic_base + EN0_RSARHI);
	outb(E8390_RREAD+E8390_START, nic_base + NE_CMD);

	if (ei_status.ne2k_flags & ONLY_16BIT_IO) {
		insw(NE_BASE + NE_DATAPORT,buf,count>>1);
		if (count & 0x01) {
			buf[count-1] = inb(NE_BASE + NE_DATAPORT);
		}
	} else {
		insl(NE_BASE + NE_DATAPORT, buf, count>>2);
		if (count & 3) {
			buf += count & ~3;
			if (count & 2)
				*((u16*)buf)++ = le16_to_cpu(inw(NE_BASE + NE_DATAPORT));
			if (count & 1)
				*buf = inb(NE_BASE + NE_DATAPORT);
		}
	}

	outb(ENISR_RDC, nic_base + EN0_ISR);	/* Ack intr. */
	ei_status.dmaing &= ~0x01;
}

static void ne2k_pci_block_output(struct net_device *dev, int count,
				  const unsigned char *buf, const int start_page)
{
	long nic_base = NE_BASE;
	unsigned long dma_start;

	/* On little-endian it's always safe to round the count up for
	   word writes. */
	if (ei_status.ne2k_flags & ONLY_32BIT_IO)
		count = (count + 3) & 0xFFFC;
	else
		if (count & 0x01)
			count++;

	/* This *shouldn't* happen. If it does, it's the last thing you'll see */
	if (ei_status.dmaing) {
		printk("%s: DMAing conflict in ne2k_pci_block_output."
			   "[DMAstat:%d][irqlock:%d]\n",
			   dev->name, ei_status.dmaing, ei_status.irqlock);
		return;
	}
	ei_status.dmaing |= 0x01;
	/* We should already be in page 0, but to be safe... */
	outb(E8390_PAGE0+E8390_START+E8390_NODMA, nic_base + NE_CMD);

#ifdef NE8390_RW_BUGFIX
	/* Handle the read-before-write bug the same way as the
	   Crynwr packet driver -- the NatSemi method doesn't work.
	   Actually this doesn't always work either, but if you have
	   problems with your NEx000 this is better than nothing! */
	outb(0x42, nic_base + EN0_RCNTLO);
	outb(0x00, nic_base + EN0_RCNTHI);
	outb(0x42, nic_base + EN0_RSARLO);
	outb(0x00, nic_base + EN0_RSARHI);
	outb(E8390_RREAD+E8390_START, nic_base + NE_CMD);
#endif
	outb(ENISR_RDC, nic_base + EN0_ISR);

   /* Now the normal output. */
	outb(count & 0xff, nic_base + EN0_RCNTLO);
	outb(count >> 8,   nic_base + EN0_RCNTHI);
	outb(0x00, nic_base + EN0_RSARLO);
	outb(start_page, nic_base + EN0_RSARHI);
	outb(E8390_RWRITE+E8390_START, nic_base + NE_CMD);
	if (ei_status.ne2k_flags & ONLY_16BIT_IO) {
		outsw(NE_BASE + NE_DATAPORT, buf, count>>1);
	} else {
		outsl(NE_BASE + NE_DATAPORT, buf, count>>2);
		if (count & 3) {
			buf += count & ~3;
			if (count & 2)
				outw(cpu_to_le16(*((u16*)buf)++), NE_BASE + NE_DATAPORT);
		}
	}

	dma_start = jiffies;

	while ((inb(nic_base + EN0_ISR) & ENISR_RDC) == 0)
		if (jiffies - dma_start > 2) {			/* Avoid clock roll-over. */
			printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name);
			ne2k_pci_reset_8390(dev);
			NS8390_init(dev,1);
			break;
		}

	outb(ENISR_RDC, nic_base + EN0_ISR);	/* Ack intr. */
	ei_status.dmaing &= ~0x01;
	return;
}

static int netdev_ethtool_ioctl(struct net_device *dev, void *useraddr)
{
	struct ei_device *ei = dev->priv;
	struct pci_dev *pci_dev = (struct pci_dev *) ei->priv;
	u32 ethcmd;
		
	if (copy_from_user(&ethcmd, useraddr, sizeof(ethcmd)))
		return -EFAULT;

        switch (ethcmd) {
        case ETHTOOL_GDRVINFO: {
		struct ethtool_drvinfo info = {ETHTOOL_GDRVINFO};
		strcpy(info.driver, DRV_NAME);
		strcpy(info.version, DRV_VERSION);
		strcpy(info.bus_info, pci_dev->slot_name);
		if (copy_to_user(useraddr, &info, sizeof(info)))
			return -EFAULT;
		return 0;
	}

        }
	
	return -EOPNOTSUPP;
}

static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
{
	switch(cmd) {
	case SIOCETHTOOL:
		return netdev_ethtool_ioctl(dev, (void *) rq->ifr_data);
	default:
		return -EOPNOTSUPP;
	}
}

static void __devexit ne2k_pci_remove_one (struct pci_dev *pdev)
{
	struct net_device *dev = pci_get_drvdata(pdev);

	if (!dev)
		BUG();

	unregister_netdev(dev);
	release_region(dev->base_addr, NE_IO_EXTENT);
	kfree(dev);
	pci_set_drvdata(pdev, NULL);
}


static struct pci_driver ne2k_driver = {
	name:		DRV_NAME,
	probe:		ne2k_pci_init_one,
	remove:		__devexit_p(ne2k_pci_remove_one),
	id_table:	ne2k_pci_tbl,
};


static int __init ne2k_pci_init(void)
{
/* when a module, this is printed whether or not devices are found in probe */
#ifdef MODULE
	printk(version);
#endif
	return pci_module_init (&ne2k_driver);
}


static void __exit ne2k_pci_cleanup(void)
{
	pci_unregister_driver (&ne2k_driver);
}

module_init(ne2k_pci_init);
module_exit(ne2k_pci_cleanup);