config.in

linux下hpi口驱动程序

#
# Character device configuration
#
mainmenu_option next_comment
comment 'Character devices'

tristate 'HPI support' CONFIG_HPI

bool 'Virtual terminal' CONFIG_VT
if [ "$CONFIG_VT" = "y" ]; then
   bool '  Support for console on virtual terminal' CONFIG_VT_CONSOLE
   if [ "$CONFIG_GSC_LASI" = "y" ]; then
      bool '    Support for Lasi/Dino PS2 port' CONFIG_GSC_PS2
   fi
fi
tristate 'Standard/generic (8250/16550 and compatible UARTs) serial support' CONFIG_SERIAL
if [ "$CONFIG_SERIAL" = "y" ]; then
   bool '  Support for console on serial port' CONFIG_SERIAL_CONSOLE
   if [ "$CONFIG_GSC_LASI" = "y" ]; then
      bool '   serial port on GSC support' CONFIG_SERIAL_GSC
   fi
   if [ "$CONFIG_IA64" = "y" ]; then
      bool '  Support for serial port described by EFI HCDP table' CONFIG_SERIAL_HCDP
   fi
fi
if [ "$CONFIG_ARCH_ACORN" = "y" ]; then
   dep_tristate '   Atomwide serial port support' CONFIG_ATOMWIDE_SERIAL $CONFIG_SERIAL
   dep_tristate '   Dual serial port support' CONFIG_DUALSP_SERIAL $CONFIG_SERIAL
fi
dep_mbool 'Extended dumb serial driver options' CONFIG_SERIAL_EXTENDED $CONFIG_SERIAL
if [ "$CONFIG_SERIAL_EXTENDED" = "y" ]; then
   bool '  Support more than 4 serial ports' CONFIG_SERIAL_MANY_PORTS
   bool '  Support for sharing serial interrupts' CONFIG_SERIAL_SHARE_IRQ
   bool '  Autodetect IRQ on standard ports (unsafe)' CONFIG_SERIAL_DETECT_IRQ
   bool '  Support special multiport boards' CONFIG_SERIAL_MULTIPORT
   bool '  Support the Bell Technologies HUB6 card' CONFIG_HUB6
fi
bool 'Non-standard serial port support' CONFIG_SERIAL_NONSTANDARD
if [ "$CONFIG_SERIAL_NONSTANDARD" = "y" ]; then
   tristate '  Computone IntelliPort Plus serial support' CONFIG_COMPUTONE
   tristate '  Comtrol Rocketport support' CONFIG_ROCKETPORT
   tristate '  Cyclades async mux support' CONFIG_CYCLADES
   if [ "$CONFIG_EXPERIMENTAL" = "y" -a "$CONFIG_CYCLADES" != "n" ]; then
      bool '    Cyclades-Z interrupt mode operation (EXPERIMENTAL)' CONFIG_CYZ_INTR
   fi
   if [ "$CONFIG_X86_64" != "y" ]; then
      tristate '  Digiboard Intelligent Async Support' CONFIG_DIGIEPCA
      if [ "$CONFIG_DIGIEPCA" = "n" ]; then
         tristate '  Digiboard PC/Xx Support' CONFIG_DIGI
      fi
   fi
   dep_tristate '  Hayes ESP serial port support' CONFIG_ESPSERIAL $CONFIG_ISA
   tristate '  Moxa Intellio support' CONFIG_MOXA_INTELLIO
   tristate '  Moxa SmartIO support' CONFIG_MOXA_SMARTIO
   if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then
      dep_tristate '  Multi-Tech multiport card support (EXPERIMENTAL)' CONFIG_ISI m
   fi
   tristate '  Microgate SyncLink card support' CONFIG_SYNCLINK
   tristate '  SyncLink Multiport support' CONFIG_SYNCLINKMP
   tristate '  HDLC line discipline support' CONFIG_N_HDLC
   tristate '  SDL RISCom/8 card support' CONFIG_RISCOM8
   if [ "$CONFIG_X86_64" != "y" ]; then
      tristate '  Specialix IO8+ card support' CONFIG_SPECIALIX
      if [ "$CONFIG_SPECIALIX" != "n" ]; then
         bool '  Specialix DTR/RTS pin is RTS' CONFIG_SPECIALIX_RTSCTS
      fi 
      tristate '  Specialix SX (and SI) card support' CONFIG_SX
      tristate '  Specialix RIO system support' CONFIG_RIO
      if [ "$CONFIG_RIO" != "n" ]; then
        bool '    Support really old RIO/PCI cards' CONFIG_RIO_OLDPCI
      fi
   fi
   bool '  Stallion multiport serial support' CONFIG_STALDRV
   if [ "$CONFIG_STALDRV" = "y" ]; then
     tristate '    Stallion EasyIO or EC8/32 support' CONFIG_STALLION
     tristate '    Stallion EC8/64, ONboard, Brumby support' CONFIG_ISTALLION
   fi
   if [ "$CONFIG_PARISC" = "y" ]; then
     if [ "$CONFIG_PDC_CONSOLE" != "y" ]; then
       bool '  Serial MUX support' CONFIG_SERIAL_MUX CONFIG_SERIAL_NONSTANDARD
     fi
     if [ "$CONFIG_SERIAL_MUX" != "y" ]; then
       bool '  PDC software console support' CONFIG_PDC_CONSOLE CONFIG_SERIAL_NONSTANDARD
     fi
   fi
   if [ "$CONFIG_MIPS" = "y" ]; then
      bool '  TX3912/PR31700 serial port support' CONFIG_SERIAL_TX3912
      dep_bool '     Console on TX3912/PR31700 serial port' CONFIG_SERIAL_TX3912_CONSOLE $CONFIG_SERIAL_TX3912
      bool '  TMPTX39XX/49XX serial port support' CONFIG_SERIAL_TXX9
      dep_bool '     Console on TMPTX39XX/49XX serial port' CONFIG_SERIAL_TXX9_CONSOLE $CONFIG_SERIAL_TXX9
      if [ "$CONFIG_SOC_AU1X00" = "y" ]; then
	 bool '  Enable Au1x00 UART Support' CONFIG_AU1X00_UART
	 if [ "$CONFIG_AU1X00_UART" = "y" ]; then
	    bool '        Enable Au1x00 serial console' CONFIG_AU1X00_SERIAL_CONSOLE
         fi
         dep_tristate '  Au1x00 USB TTY Device support' CONFIG_AU1X00_USB_TTY $CONFIG_SOC_AU1X00
	    if [ "$CONFIG_AU1000_USB_TTY" != "y" ]; then
	       dep_tristate '  Au1x00 USB Raw Device support' CONFIG_AU1X00_USB_RAW $CONFIG_SOC_AU1X00
	    fi
	    if [ "$CONFIG_AU1X00_USB_TTY" != "n" -o \
	         "$CONFIG_AU1X00_USB_RAW" != "n" ]; then
		 define_bool CONFIG_AU1X00_USB_DEVICE y
	    fi
      fi
      bool '  TXx927 SIO support' CONFIG_TXX927_SERIAL 
      if [ "$CONFIG_TXX927_SERIAL" = "y" ]; then
         bool '    TXx927 SIO Console support' CONFIG_TXX927_SERIAL_CONSOLE  
      fi                             
      if [ "$CONFIG_SIBYTE_SB1xxx_SOC" = "y" ]; then
         bool '  Support for BCM1xxx onchip DUART' CONFIG_SIBYTE_SB1250_DUART
         if [ "$CONFIG_SIBYTE_SB1250_DUART" = "y" ]; then
            bool '    Console on BCM1xxx DUART' CONFIG_SIBYTE_SB1250_DUART_CONSOLE
            if [ "$CONFIG_SIBYTE_SB1250_DUART_CONSOLE" = "y" ]; then
               define_bool CONFIG_SERIAL_CONSOLE y
            fi
         fi
      fi
   fi
   if [ "$CONFIG_DECSTATION" = "y" ]; then
      bool '  DECstation serial support' CONFIG_SERIAL_DEC
      dep_bool '    Support for console on a DECstation serial port' CONFIG_SERIAL_DEC_CONSOLE $CONFIG_SERIAL_DEC
      dep_bool '    DZ11 serial support' CONFIG_DZ $CONFIG_SERIAL_DEC $CONFIG_MIPS32
      dep_bool '    Z85C30 serial support' CONFIG_ZS $CONFIG_SERIAL_DEC $CONFIG_TC
   fi
   if [ "$CONFIG_SGI_IP22" = "y" ]; then
      bool '  SGI Zilog85C30 serial support' CONFIG_IP22_SERIAL
   fi
   if [ "$CONFIG_IA64" = "y" ]; then
      bool '  SGI SN2 l1 serial port support' CONFIG_SGI_L1_SERIAL
      if [ "$CONFIG_SGI_L1_SERIAL" = "y" ]; then
	 bool '    SGI SN2 l1 Console support' CONFIG_SGI_L1_SERIAL_CONSOLE
      fi
      if [ "$CONFIG_IA64_GENERIC" = "y" -o "$CONFIG_IA64_SGI_SN2" = "y" ]; then
	 bool '  SGI SN2 IOC4 serial port support' CONFIG_SGI_IOC4_SERIAL
      fi
   fi
   if [ "$CONFIG_PARISC" = "y" ]; then
     bool '  PDC software console support' CONFIG_PDC_CONSOLE
   fi
   if [ "$CONFIG_PARISC" = "y" ]; then
     bool '  PDC software console support' CONFIG_PDC_CONSOLE
   fi
fi
if [ "$CONFIG_MIPS_ITE8172" = "y" ]; then
   bool 'Enable Qtronix 990P Keyboard Support' CONFIG_QTRONIX_KEYBOARD
   if [ "$CONFIG_QTRONIX_KEYBOARD" = "y" ]; then
     define_bool CONFIG_IT8172_CIR y
   else
     bool '    Enable PS2 Keyboard Support' CONFIG_PC_KEYB
   fi
   bool 'Enable Smart Card Reader 0 Support ' CONFIG_IT8172_SCR0
   bool 'Enable Smart Card Reader 1 Support ' CONFIG_IT8172_SCR1
fi
if [ "$CONFIG_MIPS_IVR" = "y" ]; then
   bool 'Enable Qtronix 990P Keyboard Support' CONFIG_QTRONIX_KEYBOARD
   if [ "$CONFIG_QTRONIX_KEYBOARD" = "y" ]; then
     define_bool CONFIG_IT8172_CIR y
   fi
   bool 'Enable Smart Card Reader 0 Support ' CONFIG_IT8172_SCR0
fi
if [ "$CONFIG_CPU_VR41XX" = "y" ]; then
   bool 'NEC VR4100 series Keyboard Interface Unit Support ' CONFIG_VR41XX_KIU
fi
if [ "$CONFIG_ARCH_AT91RM9200" = "y" ]; then
  tristate 'AT91RM9200 SPI device interface' CONFIG_AT91_SPIDEV
fi

source drivers/serial/Config.in

if [ "$CONFIG_ARCH_ANAKIN" = "y" ]; then
   tristate 'Anakin touchscreen support' CONFIG_TOUCHSCREEN_ANAKIN
fi

bool 'Unix98 PTY support' CONFIG_UNIX98_PTYS
if [ "$CONFIG_UNIX98_PTYS" = "y" ]; then
   int 'Maximum number of Unix98 PTYs in use (0-2048)' CONFIG_UNIX98_PTY_COUNT 256
fi
if [ "$CONFIG_PARPORT" != "n" ]; then
   dep_tristate 'Parallel printer support' CONFIG_PRINTER $CONFIG_PARPORT
   if [ "$CONFIG_PRINTER" != "n" ]; then
      bool '  Support for console on line printer' CONFIG_LP_CONSOLE
   fi
   dep_tristate 'Support for user-space parallel port device drivers' CONFIG_PPDEV $CONFIG_PARPORT
   dep_tristate 'Texas Instruments parallel link cable support' CONFIG_TIPAR $CONFIG_PARPORT
fi

if [ "$CONFIG_PPC64" = "y" ] ; then 
   bool 'pSeries Hypervisor Virtual Console support' CONFIG_HVC_CONSOLE
fi
if [ "$CONFIG_ALL_PPC" = "y" ]; then
   tristate 'Total Impact briQ front panel driver' CONFIG_BRIQ_PANEL
fi

source drivers/i2c/Config.in

if [ "$CONFIG_I2C" != "n" ]; then
    dep_tristate '  DS1307 RTC' CONFIG_I2C_DS1307 $CONFIG_I2C
fi

source drivers/l3/Config.in

mainmenu_option next_comment
comment 'Mice'
tristate 'Bus Mouse Support' CONFIG_BUSMOUSE
if [ "$CONFIG_BUSMOUSE" != "n" ]; then
   dep_tristate '  ATIXL busmouse support' CONFIG_ATIXL_BUSMOUSE $CONFIG_BUSMOUSE
   dep_tristate '  Logitech busmouse support' CONFIG_LOGIBUSMOUSE $CONFIG_BUSMOUSE
   dep_tristate '  Microsoft busmouse support' CONFIG_MS_BUSMOUSE $CONFIG_BUSMOUSE
   if [ "$CONFIG_ADB" = "y" -a "$CONFIG_ADB_KEYBOARD" = "y" ]; then
      dep_tristate '  Apple Desktop Bus mouse support (old driver)' CONFIG_ADBMOUSE $CONFIG_BUSMOUSE
   fi
#   if [ "$CONFIG_DECSTATION" = "y" ]; then
#      dep_bool '  MAXINE Access.Bus mouse (VSXXX-BB/GB) support' CONFIG_DTOP_MOUSE $CONFIG_ACCESSBUS