tft_spfd54124b_zhonghang.c

ARMSTM32 lcd驱动程序集锦

	else
	{
		SPFD54124B_ZH_SEND_COMMAND(0x36);
		SPFD54124B_ZH_SEND_DATA(0xc8);
	}


	SPFD54124B_ZH_set_display_window(top,left , bottom, right);	

	if (is_invert)
	{
		for (j = left; j <= right; j++)
		{		
			for (i = top; i <= bottom; i++)
			{
				SPFD54124B_ZH_SEND_DATA( *(buf_ptr + j * MP4_MAX_WIDTH+ i) ); 
			}
		}			
	}
	else
	{
		for (j = top; j <= bottom; j++)
		{
			for (i = left; i <= right; i++)
			{
				SPFD54124B_ZH_SEND_DATA( *(buf_ptr + j * MP4_MAX_WIDTH+ i) );
			}
		}				
	}	

	SPFD54124B_ZH_SEND_COMMAND(0x36);
	SPFD54124B_ZH_SEND_DATA(0xc8);
	
	return ERR_LCD_NONE;
}
/*@Zhemin.Lin, CR9122, begin*/

static LCD_SPEC_T g_SPFD54124B_ZH_spec =
{
	0,		//uint8	rgb_sequence; 		/*rgb sequence*/
										/*0: R-G-B, 1: B-G-R*/
	10,		//uint8	min_cycle_read;		/*read cycle:  ns*/
	50,		//uint8	min_cycle_write;	/*write cycle: ns*/
	0,		//uint8	cyclenum_sendaddr;	/*operation cycle to send address*/
										/* 0: once, 1:twice*/
	0,		//uint8	cyclenum_senddata;	/*operation cycle to send data */
										/* 0; once, 1:twice*/
	1,		//uint8	cmd_num_setupwin;	/*command number to settint up widnow space*/
										/*0: 4 commands for setting up window space: x-start, x-end, y-start, y-end*/
										/*1: 2 commands for setting up window space: x-address, y-address*/
										/*2: 1 commanns for setting up window space window address*/
										/*3: no commands for setting up window space*/
	1,		//uint8	method_send_cmdaddr;/*how to send command & address*/
										/*0: sending together, 1:sending separately*/
	1,		//uint8	ads_is_high;		/*status of ADS when sending parameter*/
										/*0: low, 1: high*/
	0,		//uint8	sequence_cmdaddr;	/*the sequence of command & address, if not send command & address together as 16 bits*/
										/*0: write 2 window area on a 16bit bus, Hitachi*/
										/*1, write 1 sindow area with one command, Casio*/
										/*2, write 1 command and 2 parameters separately, Samsung*/
										/*3, reserved*/
										/*4, write 1 command, 2 parameters for page, 4 parameters for column, Epson*/
										/*5, write 1 command, 4 parameters for page, 2 parameters for column*/
										/*6, write 1 command, write 4 parameters for each page/column*/
	4,		//uint8	cyclenum_setupwin;	/*operation cycle to set up window*/
	1,		//uint8	method_gram_access;	/*select method to begin actul data read/write address for selected window area in GRAM*/
										/*0: without any assigning x/y address, use initial start address of window*/
										/*1: assign 1 x/y set command and parameter onto 16bit bus at onece*/
										/*2: use separate for X and Y, with upper byte consists of command and lower byte for parameter*/
										/*3, 1 command for selecting X/Y adn 2 parameters, us command and parameter separately*/
										/*4, set different command for x and y, and command and parameter differs*/
	1,		//uint8	sequence_gram_access;/*read/write command and sequence for GRAM*/
										/*0: perform read/write without seperate read/write command but by strobe 'high' ADS(RS)pin, samsung*/
										/*1: data cycle comes right afer read/write command, Toshiba/Matsushita/Hitachi/NEC*/
										/*2: after read/write command follows start address parameter for X and Y and follows data cycle, Casio*/
										/*3: similiar to 2 but sends X and Y parameters together on 16 bit BUS*/
	0,		//uint8	order_xy;			/*order of x and y address, I think, this field is active when sequence_gram_access = 2*/
										/*0: X first*/
										/*1: Y first*/
	1,		//uint8	is_dummy_read;		/*deciding first read data when reading GRAM*/
										/*0: acknowledge first data as valid data*/
										/*1: acknowledge first data as dummy data*/
	3,		//uint8	cyclenum_read;		/*total cycle numbers needed to access GRAM read/write*/
	0x44,	//uint8	win_setstartx_cmd;	/*window x start address set command*/
	0x00,	//uint8	win_setendx_cmd;	/*window x end address set command*/
	0x45,	//uint8	win_setstarty_cmd;	/*window y start address set command*/
	0x00,	//uint8	win_setendy_cmd;	/*window y end address set command*/
	0x21,	//uint8	gram_setx_cmd;		/*gram x address set command*/
	0x00,	//uint8	gram_sety_cmd;		/*gram y address set command*/
	0x22,	//uint8	gram_read_cmd;		/*gram read command*/
	0x22,	//uint8	gram_write_cmd;		/*gram write command*/
	//@zhemin.lin, add 1 line, CR9590
	0x00,	//uint8	line_offset;		/*line offset for display on lcd*/
	0x00	//uint8 colum_offset        /*columoffset for display on lcd*/
};


/******************************************************************************/
//  Description:    get the important parameter for digital camera
//	Global resource dependence: 
//  Author:         Zhemin.lin
//	Note:           
/******************************************************************************/
LOCAL ERR_LCD_E  SPFD54124B_ZH_GetMainLcdSpec(
	LCD_SPEC_T *spec_ptr 	//spec struct pointer
	)
{
	if (spec_ptr == PNULL)
	{
		return 1;
	}
	
	memcpy(spec_ptr, &g_SPFD54124B_ZH_spec, sizeof(LCD_SPEC_T));
	
	return ERR_LCD_NONE;
}
/******************************************************************************/
//  Description:   Enter/Exit sleep mode .
//	Global resource dependence: 
//  Author:         Jim.zhang
//	Note:
/******************************************************************************/
LOCAL ERR_LCD_E  SPFD54124B_ZH_EnterSleep(
	BOOLEAN is_sleep 	//SCI_TRUE: exter sleep mode;SCI_FALSE:exit sleep mode.
	)
{

	if ( is_sleep ) // enter sleep mode.
	{
	
		SPFD54124B_ZH_GoSleep(); 
	}
	else 			// out sleep mode 
	{
		//SPFD54124B_ZH_reset();
		SPFD54124B_ZH_ExitSleep();
		Delayms(100);
	}

	/*
	if( !GetUdiskState())
	DC_EnterSleep(is_sleep);
	*/
	return ERR_LCD_NONE;
	}


/*****************************************************************************/
//  Description:    Enable lcd to partial display mode, so can save power.
//	Global resource dependence: 
//  Author:         Jim.zhang
//  Return:         SCI_TRUE:SUCCESS ,SCI_FALSE:failed.
//	Note:           If all input parameters are 0, exit partial display mode.
/*****************************************************************************/
LOCAL ERR_LCD_E SPFD54124B_ZH_SetDisplayWindow(
	uint16 left, 		//left of the window
	uint16 top,			//top of the window
	uint16 right,		//right of the window
	uint16 bottom		//bottom of the window
	)
{
	SPFD54124B_ZH_set_display_window(left, top, right, bottom);

	return ERR_LCD_NONE;
}

/*********************************************************************/
//  Description:   Initialize color LCD : SPFD54124B_ZH
//  Input:
//      None.
//  Author:         yinchun.li
//  Return:
//      None.
//	Note:
//  modify:  jim.cui  2005.0728 add dma init  
/*********************************************************************/
LOCAL ERR_LCD_E SPFD54124B_ZH_Init(void)
{
	
	//dma init
	dma_init ();
	
	//SPFD54124B_ZH_HW_reset();
	SPFD54124B_ZH_reset();
	
	SPFD54124B_ZH_Clear( 0xf25f );
	
	return ERR_LCD_NONE;
}


/******************************************************************************/
//  Description:  set the contrast value 
//	Global resource dependence: 
//  Author:         Jim.zhang
//	Note:
/******************************************************************************/
LOCAL ERR_LCD_E   SPFD54124B_ZH_SetContrast(
	uint16  contrast	//contrast value to set
	)
{
	return ERR_LCD_FUNC_NOT_SUPPORT;
} 


/*****************************************************************************/
//  Description:    Set the brightness of LCD.
//	Global resource dependence: 
//  Author:         Jim.zhang
//	Note:
/*****************************************************************************/
LOCAL ERR_LCD_E   SPFD54124B_ZH_SetBrightness(
	uint16 brightness	//birghtness to set
	)
{
	return ERR_LCD_FUNC_NOT_SUPPORT;
}

/******************************************************************************/
//  Description:   Close the lcd.(include sub lcd.)
//	Global resource dependence: 
//  Author:         Jim.zhang
//	Note:
/******************************************************************************/
LOCAL void SPFD54124B_ZH_Close()
{
    GPIO_SetLcdBackLight( SCI_FALSE );
    SPFD54124B_ZH_EnterSleep( SCI_TRUE );	
}


LOCAL LCD_OPERATIONS_T SPFD54124B_ZH_operations = 
{
	SPFD54124B_ZH_Init,
	SPFD54124B_ZH_EnterSleep,
	SPFD54124B_ZH_SetContrast,
	SPFD54124B_ZH_SetBrightness,
	SPFD54124B_ZH_SetDisplayWindow,
	SPFD54124B_ZH_GetInfo,
	SPFD54124B_ZH_InvalidateRect,
	SPFD54124B_ZH_InvalidateRectImage,
	SPFD54124B_ZH_Invalidate,
	SPFD54124B_ZH_Clear,
	SPFD54124B_ZH_Close,
	SPFD54124B_ZH_GetMainLcdSpec
};

/******************************************************************************/
//  Description:  return the SPFD54124B_ZH lcd driver funtion pointer
//	Global resource dependence: 
//  Author:         Jim.zhang
//	Note:
/******************************************************************************/
PUBLIC LCD_OPERATIONS_T* SPFD54124B_ZH_GetOperations()
{
	return &SPFD54124B_ZH_operations;
}

PUBLIC BOOLEAN SPFD54124B_ZH_Probe(void)
{
	return SCI_TRUE;
}


LOCAL SPFD54124B_ZH_GoSleep(void)
{
	SPFD54124B_ZH_SEND_COMMAND(0x28); // display off 
	SPFD54124B_ZH_SEND_COMMAND(0x10); // into sleep
}

LOCAL SPFD54124B_ZH_ExitSleep(void)
{
	SPFD54124B_ZH_SEND_COMMAND(0x11); // out sleep
	Delayms(150);
	SPFD54124B_ZH_SEND_COMMAND(0x29); // display on
    Delayms(20);
	

}
#if 0
LOCAL void main_lcd_fill_rect(uint16 left, uint16 top,uint16 right,  uint16 bottom,uint16 color)
{
	uint16 i,j;
	uint16 *buf_ptr = (uint16 *)LCD_GetLCDBuffer();
	for(i = top; i < bottom;i++)
  {
    for(j = left; j < right; j++)
    {                 
    	*(buf_ptr+i*SPFD54124B_ZH_WIDTH+j)=color;
    }
  }

}
 void TestMainLcd(void)
{
	main_lcd_fill_rect(0,SPFD54124B_ZH_WIDTH-1, 0, SPFD54124B_ZH_HEIGHT-1, 0x0780);	
	while(1)
	{
		SPFD54124B_ZH_Invalidate();			
	}
}
#endif

/**---------------------------------------------------------------------------*
 **                         Compiler Flag                                     *
 **---------------------------------------------------------------------------*/
#ifdef   __cplusplus
    }
#endif