⭐ 欢迎来到虫虫下载站! | 📦 资源下载 📁 资源专辑 ℹ️ 关于我们
⭐ 虫虫下载站

📄 复件 autoenglish.dat

📁 aotu english chinese dictionary
💻 DAT
📖 第 1 页 / 共 5 页
字号:
轮椅升降机
Wheel chair lift 
图例 
legend 
工位 
station 
吊运装置 
overhead hoist 
更衣室 
restroom 
1号厂房工艺布置方案图 
proposal of the Plant I layout 
合笼 
mate 
底盘平移台 
chassis shuttle 
车辆转移台 
bus transfer 
前围角板 
front wall angle cover 
后围侧板 
rear wall side cover 
保险杠 
bumper 
三类底盘 
three type chassis 
左侧围应力蒙皮 
R/S stretching skin (road side) 
中涂 
floating coat 
拼装台 
collector 
切割轮口 
wheel -arch cutting 
内饰 
trim 
线束 
harness 
返工 
re-doing 
轮罩护板 
wheel house 
发车前准备 
pre-delivery 
举升 
hoist 
小批量产品 
be pilot 
2 套 
two kits 
配电站 
power transformer substation 
裙板 
skirt 
发动机托架 
engine holding frame 
诊断报警系统 
diagnosis and alarming system 
互换性 
interchangeability 
缩微图纸 
microfiche files 
总装 
final assembly 
磷化 
phosphating 
仪表板 
dash board 
切齐 
trimming 
结构完整性 
structure integrity 
自动愈合的防腐材料 
self-healing corrosion preventative material 
长途客车 
inter-city bus 
改装厂 
refitting factory 
遮阳板 
sun visor 
随车工具 
tool box 
钢化玻璃 
toughened grass 
异形钢管 
special steel pipe 
全天候空调系统 
full range A/C 
强制通风 
ram-air ventilation 
停机时间 
downtime 
无公害柴油 
clean diesel 
宽敞悬臂式座椅 
roomy cantilevered seat 
防滑地板 
no-skid floor 
织物纹里铝合金 
textured aluminum extrution 
爬坡能力 
grade ability 
排水阀 
drain valve 
除湿器 
moisture ejector 
怠速时 
at idle 
琴式驱动桥 
banjo type drive axle 
通风口 
duct 
恒温控制 
thermostatic control 
平衡水箱 
surge tank 
变光开关 
simmer switch 
消音器 
muffler 
防破坏 
vandal resistant 
聚碳化透镜 
poly-carbonate len 
镀锌板 
galvanized plate 
搭接 
lap 
亮丽的外表 
smart apperance 
隐藏式固定 
concealed fastening 
水洼 
ponding 
发动机中置式客车 
bus with under floor engine 
组合式客车车身 
modular bus body 
薄壳式结构 
shell construction 
衬垫 
pad 
空气导流板 
air deflector 
搁梁 
shelf beam 
腰梁 
waist rail 
梭梁 
stabilizing beam 
腰带式安全带 
diagonal safety belt 
压条 
trim strip 
嵌条 
insertion strip 
翼板 
fender 
斜撑 
bracing piece 
转向盘回正性试验 
test of steering wheel returnability
转向盘转角脉冲试验 
steering wheel impulse input test
转向盘转角阶跃输入试验 
steering wheel step input or transient state yaw response test
极限侧向加速度试验 
limiting lateral acceleration test
汽车平顺性随机输入行驶试验
automobile ride random input running test
汽车平顺性单脉冲输入行驶试验
automobile ride single pulse input running test
汽车悬挂系统固有频率与阻尼比的测定试验
measurement of natural frequency and damping raito of suspension
功率突然变化影响试验 
test of effect of sudden power change
收油门后控制试验 
test of control at breakway
横风稳定性试验 
test of crosswind stability
反冲试验 
kick-back test
轮胎爆破响应时间试验
test of burst response of tyre
绕过障碍物试验
obstacle avoidance test
移线试验
lane change test
J型转弯试验
test of J turn
频率响应时间试验
frequency response test
瞬态响应时间试验
transient response test
阶路响应时间试验
step response test
脉冲响应试验
pulse response test
静态操舵力试验
static steering effort test
悬架举升试验
jack-up test of suspension
耐翻倾试验
test of overturning immunity
轮辋错动试验
rim slip test
风洞试验
wind tunnel test
制动稳定性试验
test of braking stability
最小转弯直径试验
minimum turning diameter test
操舵力试验
steering effort test
类型
type
发动机
engine
内燃机
intenal combusiton engine
动力机装置
power unit
汽油机
gasoline engine
汽油喷射式汽油机
gasoline-injection engine
火花点火式发动机
spark ignition engine
压燃式发动机
compression ignition engine
往复式内燃机
reciprocating internal combustion engine
化油器式发动机
carburetor engine
柴油机
diesel engine
转子发动机
rotary engine
旋轮线转子发动机
rotary trochoidal engine
二冲程发动机
two-stroke engine
四冲程发动机
four-stroke engine
直接喷射式柴油机
direct injection engine
间接喷射式柴油机
indirect injection engine
增压式发动机
supercharged engine
风冷式发动机
air-cooled engine
油冷式发动机
oil-cooled engine
水冷式发动机
water-cooled engine
自然进气式发动机
naturally aspirated engine
煤气机
gas engine
液化石油气发动机
liquified petroleum gas engine
柴油煤气机
diesel gas engine
多种燃料发动机
multifuel engine
石油发动机
hydrocarbon engine
双燃料发动机
duel fuel engine
热球式发动机
hot bulb engine
多气缸发动机
multiple cylinder engine
对置活塞发动机
opposed piston engine
对置气缸式发动机
opposed-cylinder engine
十字头型发动机
cross head engine
直列式发动机
in-line engine
星型发动机
radial engine
筒状活塞发动机
trunk-piston engine
斯特林发动机
stirling engine
套阀式发动机
knight engine
气孔扫气式发动机
port-scavenged engine
倾斜式发动机
slant engine
前置式发动机
front-engine
后置式发动机
rear-engine
中置式发动机
central engine
左侧发动机
left-hand engine
右侧发动机
right-hand engine
短冲程发动机
oversquare engine
长冲程发动机
undersquare engine
等径程发动机
square engine
顶置凸轮轴发动机
overhead camshaft engine
双顶置凸轮轴发动机
dual overhead camshaft engine
V形发动机
V-engine
顶置气门发动机
valve in-head engine
侧置气门发动机
side valve engine
无气门发动机
valveless engine
多气门发动机
multi-valve engine
卧式发动机
horizontal engine
斜置式发动机
inclined engine
立式发动机
vertical engine
W形发动机
w-engine
I形发动机
I-engine
L形发动机
L-engine
F形发动机
F-engine
性能
performance
二冲程循环
two-stroke cycle
四冲程循环
four-stroke cycle
狄塞尔循环
diesel cycle
奥托循环
otto cycle
混合循环
mixed cycle
定容循环
constant volume cycle
工作循环
working cycle
等压循环
constant pressure cycle
理想循环
ideal cycle
热力循环
thermodynamic cycle
冲程
stroke
活塞行程
piston stroke
长行程
long stroke
上行程
up stroke
下行程
down stroke
进气行程
intake stroke
充气行程
charging stroke
压缩行程
compression stroke
爆炸行程
explosion stroke
膨胀行程
expansion stroke
动力行程
power stroke
排气行程
exhaust stroke
膨胀换气行程
expansion-exchange stroke
换气压缩行程
exchange-compression stroke
止点
dead center
上止点
top dead center(upper dead center)
下止点
lower dead center(bottom dead center)
上止点前
budc(before upper dead center)
上止点后
atdc(after top dead cetner)
下止点前
bbdc(before bottom dead center)
下止点后
abdc(after bottom dead center)
缸径
cylinder bore
缸径与行程
bore and stroke
空气室
energy chamber
气缸余隙容积
cylinder clearance volume
燃烧室容积
combustion chamber volume
气缸最大容积
maximum cylinder volume
压缩室
compression chamber
排气量
displacement
发动机排量
engine displacement
活塞排量
piston swept volume
气缸容量
cylinder capacity
单室容量
single-chamber capacity
容积法
volumetry
压缩比
compression ratio
临界压缩比
critical compression ratio
膨胀比
expansion ratio
面容比
surface to volume ratio
行程缸径比
stroke-bore ratio
混合比
mixture ratio
压缩压力
compression pressure
制动平均有效压力
brake mean effective pressure(bmep)
空燃比
air fuel ratio
燃空比
fuel air ratio
燃料当量比
fuel equivalence ratio
扭矩
torque
单缸功率
power per cylinder
升功率
power per liter
升扭矩
torque per liter
升质量
mass per liter 
减额功率
derating power
输出马力
shaft horsepower
马力小时,马力时
horsepower-hour
总马力
gross horse power
总功率
gross power 
净功率
net power 
燃油消耗量
fuel consumption 
比燃料消耗率
specific fuel consumption
空气消耗率
air consumption
机油消耗量
oil consumption
有效马力
net horse power
额定马力
rated horse power
马力重量系数
horsepower-weight factor
制动功率
brake horse power
制动热效率
brake thermal efficiency 
总效率
overall efficiency
排烟极限功率
smoke limiting horsepower
功率曲线
power curve
机械损失
mechanical loss
机械效率
mechanical efficiency
有效热效率
effective thermal efficiency
充气系数
volumetric efficiency
过量空气系数
coefficient of excess air
适应性系数
adaptive coefficient
扭矩适应性系数
coefficient of torque adaptibility
转速适应性系数
speed adaptive coefficient
强化系数
coefficient of intensification
校正系数
correction factor
换算系数
conversion factor
活塞平均速度
mean piston speed
发动机转速
engine speed (rotational frequency)
怠速转速
idling speed
经济转速
economic speed
起动转速
starting speed
最低稳定工作转速
lowest continuous speed with load
最大扭矩转速
speed at maximum torque
最高空转转速
maximum no load governed speed
调速
speed governing 
超速
overspeed
怠速
idling
转速波动率
speed fluctuation rate
工况
working condition(operating mode)
额定工况
declared working condition
变工况
variable working condition
稳定工况
steady working condition
空载
no-load
全负荷
full load
超负荷
overload
部分负荷
part load
充量(进气)
charge
旋转方向
direction of rotation
顺时针
clockwise
逆时针
counter-clockwise
左转
left-hand rotation
右转
right-hand rotation
外径
major diameter
中径
pitch diameter
内径
minor diameter
径向间隙
radial clearance
发动机性能
engine performance
加载性能
loading performance
起动性能
starting performance
加速性能
acceleration performance
动力性能
power performance
排放性能
emission performance
空转特性
no load characteristics
负荷特性
part throttle characteristics
调速特性
governor control characteristics
万有特性
mapping characteristics
稳定调速率
steady state speed governing rate
气缸体和气缸盖
cylinder block and head
气缸体
cylinder block
整体铸造
cast inblock (cast enblock)
发动机罩
engine bonnet
气缸体加强筋
engine block stiffening rib
气缸
cylinder
(转子机)缸体
stator
缸径
cylinder bore
气缸体机架
cylinder block frame
气缸盖
cylinder head
配气机构箱
valve mechanism casing
气缸体隔片
cylinder spacer
气缸盖密封环
cylinder head ring gasket
气缸盖垫片
cylinder head gasket
气缸套
cylinder liner(cylinder sleeve)
干式缸套
dry cylinder liner
湿式缸套
wet cylinder liner
气缸水套
water jacket
膨胀塞
expansion plug
防冻塞
freeze plug
气缸壁
cylinder wall
环脊
ring ridge
排气口
exhaust port
中间隔板
intermediate bottum
导板
guideway
创成半径(转子机)
generating radius
缸体宽度(转子机)
operating width
机柱
column
燃烧室
combustion chamber
主燃烧室
main combustion chamber
副燃烧室
subsidiary combustion chamber
预燃室
prechamber
涡流燃烧室`
swirl combustion chamber
分开式燃烧室
divided combustion chamber
涡流式燃烧室
turbulence combustion chamber
半球形燃烧室
hemispherical combustion chamber
浴盆形燃烧室
bathtub section combustion chamber
L形燃烧室
L-combustion chamber
楔形燃烧室
wedge-section combustion chamber
开式燃烧室
open combustion chamber
封闭喷射室
closed spray chamber
活塞顶内燃烧室
piston chamber
爆发室
explosion chamber
燃烧室容积比
volume ratio of combustion cahmber
燃烧室口径比
surface-volume ratio of combustion chamber
通道面积比
area ratio of combustion chamber passage
曲轴箱通气口
crankcase breather
凸轮轴轴承座

⌨️ 快捷键说明

复制代码 Ctrl + C
搜索代码 Ctrl + F
全屏模式 F11
切换主题 Ctrl + Shift + D
显示快捷键 ?
增大字号 Ctrl + =
减小字号 Ctrl + -