📄 avrdude.conf
字号:
# $Id: avrdude.conf.in,v 1.127 2007/10/29 22:43:00 joerg_wunsch Exp $
#
# AVRDUDE Configuration File
#
# This file contains configuration data used by AVRDUDE which describes
# the programming hardware pinouts and also provides part definitions.
# AVRDUDE's "-C" command line option specifies the location of the
# configuration file. The "-c" option names the programmer configuration
# which must match one of the entry's "id" parameter. The "-p" option
# identifies which part AVRDUDE is going to be programming and must match
# one of the parts' "id" parameter.
#
# Possible entry formats are:
#
# programmer
# id = <id1> [, <id2> [, <id3>] ...] ; # <idN> are quoted strings
# desc = <description> ; # quoted string
# type = par | stk500 | stk500v2 | stk500pp | stk500hvsp | stk500generic |
# avr910 | butterfly | usbasp |
# jtagmki | jtagmkii | jtagmkii_isp | jtagmkii_dw |
# dragon_dw | dragon_jtag | dragon_isp | dragon_pp |
# dragon_hvsp; # programmer type
# baudrate = <num> ; # baudrate for avr910-programmer
# vcc = <num1> [, <num2> ... ] ; # pin number(s)
# reset = <num> ; # pin number
# sck = <num> ; # pin number
# mosi = <num> ; # pin number
# miso = <num> ; # pin number
# errled = <num> ; # pin number
# rdyled = <num> ; # pin number
# pgmled = <num> ; # pin number
# vfyled = <num> ; # pin number
# ;
#
# part
# id = <id> ; # quoted string
# desc = <description> ; # quoted string
# has_jtag = <yes/no> ; # part has JTAG i/f
# has_debugwire = <yes/no> ; # part has debugWire i/f
# devicecode = <num> ; # deprecated, use stk500_devcode
# stk500_devcode = <num> ; # numeric
# avr910_devcode = <num> ; # numeric
# signature = <num> <num> <num> ; # signature bytes
# chip_erase_delay = <num> ; # micro-seconds
# reset = dedicated | io;
# retry_pulse = reset | sck;
# pgm_enable = <instruction format> ;
# chip_erase = <instruction format> ;
# chip_erase_delay = <num> ; # chip erase delay (us)
# # STK500 parameters (parallel programming IO lines)
# pagel = <num> ; # pin name in hex, i.e., 0xD7
# bs2 = <num> ; # pin name in hex, i.e., 0xA0
# serial = <yes/no> ; # can use serial downloading
# parallel = <yes/no/pseudo>; # can use par. programming
# # STK500v2 parameters, to be taken from Atmel's XML files
# timeout = <num> ;
# stabdelay = <num> ;
# cmdexedelay = <num> ;
# synchloops = <num> ;
# bytedelay = <num> ;
# pollvalue = <num> ;
# pollindex = <num> ;
# predelay = <num> ;
# postdelay = <num> ;
# pollmethod = <num> ;
# mode = <num> ;
# delay = <num> ;
# blocksize = <num> ;
# readsize = <num> ;
# hvspcmdexedelay = <num> ;
# # STK500v2 HV programming parameters, from XML
# pp_controlstack = <num>, <num>, ...; # PP only
# hvsp_controlstack = <num>, <num>, ...; # HVSP only
# hventerstabdelay = <num>;
# progmodedelay = <num>; # PP only
# latchcycles = <num>;
# togglevtg = <num>;
# poweroffdelay = <num>;
# resetdelayms = <num>;
# resetdelayus = <num>;
# hvleavestabdelay = <num>;
# resetdelay = <num>;
# synchcycles = <num>; # HVSP only
# chiperasepulsewidth = <num>; # PP only
# chiperasepolltimeout = <num>;
# chiperasetime = <num>; # HVSP only
# programfusepulsewidth = <num>; # PP only
# programfusepolltimeout = <num>;
# programlockpulsewidth = <num>; # PP only
# programlockpolltimeout = <num>;
# # JTAG ICE mkII parameters, also from XML files
# allowfullpagebitstream = <yes/no> ;
# enablepageprogramming = <yes/no> ;
# idr = <num> ; # IO addr of IDR (OCD) reg.
# rampz = <num> ; # IO addr of RAMPZ reg.
# spmcr = <num> ; # mem addr of SPMC[S]R reg.
# eecr = <num> ; # mem addr of EECR reg.
# # (only when != 0x3c)
#
# memory <memtype>
# paged = <yes/no> ; # yes / no
# size = <num> ; # bytes
# page_size = <num> ; # bytes
# num_pages = <num> ; # numeric
# min_write_delay = <num> ; # micro-seconds
# max_write_delay = <num> ; # micro-seconds
# readback_p1 = <num> ; # byte value
# readback_p2 = <num> ; # byte value
# pwroff_after_write = <yes/no> ; # yes / no
# read = <instruction format> ;
# write = <instruction format> ;
# read_lo = <instruction format> ;
# read_hi = <instruction format> ;
# write_lo = <instruction format> ;
# write_hi = <instruction format> ;
# loadpage_lo = <instruction format> ;
# loadpage_hi = <instruction format> ;
# writepage = <instruction format> ;
# ;
# ;
#
# If any of the above parameters are not specified, the default value
# of 0 is used for numerics or the empty string ("") for string
# values. If a required parameter is left empty, AVRDUDE will
# complain.
#
# NOTES:
# * 'devicecode' is the device code used by the STK500 (see codes
# listed below)
# * Not all memory types will implement all instructions.
# * AVR Fuse bits and Lock bits are implemented as a type of memory.
# * Example memory types are:
# "flash", "eeprom", "fuse", "lfuse" (low fuse), "hfuse" (high
# fuse), "signature", "calibration", "lock"
# * The memory type specified on the avrdude command line must match
# one of the memory types defined for the specified chip.
# * The pwroff_after_write flag causes avrdude to attempt to
# power the device off and back on after an unsuccessful write to
# the affected memory area if VCC programmer pins are defined. If
# VCC pins are not defined for the programmer, a message
# indicating that the device needs a power-cycle is printed out.
# This flag was added to work around a problem with the
# at90s4433/2333's; see the at90s4433 errata at:
#
# http://www.atmel.com/atmel/acrobat/doc1280.pdf
#
# INSTRUCTION FORMATS
#
# Instruction formats are specified as a comma seperated list of
# string values containing information (bit specifiers) about each
# of the 32 bits of the instruction. Bit specifiers may be one of
# the following formats:
#
# '1' = the bit is always set on input as well as output
#
# '0' = the bit is always clear on input as well as output
#
# 'x' = the bit is ignored on input and output
#
# 'a' = the bit is an address bit, the bit-number matches this bit
# specifier's position within the current instruction byte
#
# 'aN' = the bit is the Nth address bit, bit-number = N, i.e., a12
# is address bit 12 on input, a0 is address bit 0.
#
# 'i' = the bit is an input data bit
#
# 'o' = the bit is an output data bit
#
# Each instruction must be composed of 32 bit specifiers. The
# instruction specification closely follows the instruction data
# provided in Atmel's data sheets for their parts.
#
# See below for some examples.
#
#
# The following are STK500 part device codes to use for the
# "devicecode" field of the part. These came from Atmel's software
# section avr061.zip which accompanies the application note
# AVR061 available from:
#
# http://www.atmel.com/atmel/acrobat/doc2525.pdf
#
#define ATTINY10 0x10
#define ATTINY11 0x11
#define ATTINY12 0x12
#define ATTINY15 0x13
#define ATTINY13 0x14
#define ATTINY22 0x20
#define ATTINY26 0x21
#define ATTINY28 0x22
#define ATTINY2313 0x23
#define AT90S1200 0x33
#define AT90S2313 0x40
#define AT90S2323 0x41
#define AT90S2333 0x42
#define AT90S2343 0x43
#define AT90S4414 0x50
#define AT90S4433 0x51
#define AT90S4434 0x52
#define ATMEGA48 0x59
#define AT90S8515 0x60
#define AT90S8535 0x61
#define AT90C8534 0x62
#define ATMEGA8515 0x63
#define ATMEGA8535 0x64
#define ATMEGA8 0x70
#define ATMEGA88 0x73
#define ATMEGA168 0x86
#define ATMEGA161 0x80
#define ATMEGA163 0x81
#define ATMEGA16 0x82
#define ATMEGA162 0x83
#define ATMEGA169 0x84
#define ATMEGA323 0x90
#define ATMEGA32 0x91
#define ATMEGA64 0xA0
#define ATMEGA103 0xB1
#define ATMEGA128 0xB2
#define AT90CAN128 0xB3
#define AT90CAN64 0xB3
#define AT90CAN32 0xB3
#define AT86RF401 0xD0
#define AT89START 0xE0
#define AT89S51 0xE0
#define AT89S52 0xE1
# The following table lists the devices in the original AVR910
# appnote:
# |Device |Signature | Code |
# +-------+----------+------+
# |tiny12 | 1E 90 05 | 0x55 |
# |tiny15 | 1E 90 06 | 0x56 |
# | | | |
# | S1200 | 1E 90 01 | 0x13 |
# | | | |
# | S2313 | 1E 91 01 | 0x20 |
# | S2323 | 1E 91 02 | 0x48 |
# | S2333 | 1E 91 05 | 0x34 |
# | S2343 | 1E 91 03 | 0x4C |
# | | | |
# | S4414 | 1E 92 01 | 0x28 |
# | S4433 | 1E 92 03 | 0x30 |
# | S4434 | 1E 92 02 | 0x6C |
# | | | |
# | S8515 | 1E 93 01 | 0x38 |
# | S8535 | 1E 93 03 | 0x68 |
# | | | |
# |mega32 | 1E 95 01 | 0x72 |
# |mega83 | 1E 93 05 | 0x65 |
# |mega103| 1E 97 01 | 0x41 |
# |mega161| 1E 94 01 | 0x60 |
# |mega163| 1E 94 02 | 0x64 |
# Appnote AVR109 also has a table of AVR910 device codes, which
# lists:
# dev avr910 signature
# ATmega8 0x77 0x1E 0x93 0x07
# ATmega8515 0x3B 0x1E 0x93 0x06
# ATmega8535 0x6A 0x1E 0x93 0x08
# ATmega16 0x75 0x1E 0x94 0x03
# ATmega162 0x63 0x1E 0x94 0x04
# ATmega163 0x66 0x1E 0x94 0x02
# ATmega169 0x79 0x1E 0x94 0x05
# ATmega32 0x7F 0x1E 0x95 0x02
# ATmega323 0x73 0x1E 0x95 0x01
# ATmega64 0x46 0x1E 0x96 0x02
# ATmega128 0x44 0x1E 0x97 0x02
#
# These codes refer to "BOOT" device codes which are apparently
# different than standard device codes, for whatever reasons
# (often one above the standard code).
# There are several extended versions of AVR910 implementations around
# in the Internet. These add the following codes (only devices that
# actually exist are listed):
# ATmega8515 0x3A
# ATmega128 0x43
# ATmega64 0x45
# ATtiny26 0x5E
# ATmega8535 0x69
# ATmega32 0x72
# ATmega16 0x74
# ATmega8 0x76
# ATmega169 0x78
#
# Overall avrdude defaults
#
default_parallel = "lpt1";
default_serial = "com1";
#
# PROGRAMMER DEFINITIONS
#
programmer
id = "avrisp";
desc = "Atmel AVR ISP";
type = stk500;
;
programmer
id = "avrispv2";
desc = "Atmel AVR ISP V2";
type = stk500v2;
;
programmer
id = "avrispmkII";
desc = "Atmel AVR ISP mkII";
type = stk500v2;
;
programmer
id = "avrisp2";
desc = "Atmel AVR ISP mkII";
type = stk500v2;
;
# This is supposed to be the "default" STK500 entry.
# Attempts to select the correct firmware version
# by probing for it. Better use one of the entries
# below instead.
programmer
id = "stk500";
desc = "Atmel STK500";
type = stk500generic;
;
programmer
id = "stk500v1";
desc = "Atmel STK500 Version 1.x firmware";
type = stk500;
;
programmer
id = "stk500v2";
desc = "Atmel STK500 Version 2.x firmware";
type = stk500v2;
;
programmer
id = "stk500pp";
desc = "Atmel STK500 V2 in parallel programming mode";
type = stk500pp;
;
programmer
id = "stk500hvsp";
desc = "Atmel STK500 V2 in high-voltage serial programming mode";
type = stk500hvsp;
;
programmer
id = "avr910";
desc = "Atmel Low Cost Serial Programmer";
type = avr910;
;
programmer
id = "usbasp";
desc = "USBasp, http://www.fischl.de/usbasp/";
type = usbasp;
;
programmer
id = "usbtiny";
desc = "USBtiny simple USB programmer, http://www.ladyada.net/make/usbtinyisp/";
type = usbtiny;
;
programmer
id = "butterfly";
desc = "Atmel Butterfly Development Board";
type = butterfly;
;
programmer
id = "avr109";
desc = "Atmel AppNote AVR109 Boot Loader";
type = butterfly;
;
programmer
id = "avr911";
desc = "Atmel AppNote AVR911 AVROSP";
type = butterfly;
;
programmer
id = "jtagmkI";
desc = "Atmel JTAG ICE (mkI)";
baudrate = 115200; # default is 115200
type = jtagmki;
;
# easier to type
programmer
id = "jtag1";
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -