f500_timer0_16bittimer.c

C8051F500开发编程：MCU全部资源应用实例

//-----------------------------------------------------------------------------
// F500_Timer0_16bitTimer.c
//-----------------------------------------------------------------------------
// Copyright (C) 2008 Silicon Laboratories, Inc.
// http://www.silabs.com
//
// Program Description:
//
// This program flashes the green LED on the C8051F500 target board.  The
// LED blink frequency is set using the #define BLINK_RATE
//
//
// How To Test:
//
// 1) Download code to the 'F500 target board
// 2) Ensure that the P1.3 pins are shorted together on the J19 header
// 3) Run the program.  If the LED flashes at the specified blink rate, the 
//    program is working
//
//
// Target:         C8051F500 (Side A of a C8051F500-TB)
// Tool chain:     Keil C51 8.0 / Keil EVAL C51 / SDCC
// Command Line:   None
//
// Release 1.1 / 11 JUN 2008 (ADT)
//    -Edited Formatting
//
// Release 1.0 / 18 APR 2008 (GP)
//    -Initial Revision

//-----------------------------------------------------------------------------
// Includes
//-----------------------------------------------------------------------------

#include <compiler_defs.h>
#include <C8051F500_defs.h>            // SFR declarations

//-----------------------------------------------------------------------------
// Global Constants
//-----------------------------------------------------------------------------

#define SYSCLK       24000000/8        // SYSCLK frequency in Hz

#define BLINK_RATE   10                // How often to toggle the LED per sec.
                                       // Minimum value is 1

// Reload value for Timer0 assuming a 1:48 scaling factor for Timer0 clock
#define TIMER0_RL_HIGH  (0xFFFF -((SYSCLK/48/BLINK_RATE >> 8) & 0x00FF))
#define TIMER0_RL_LOW   (0xFFFF -(SYSCLK/48/BLINK_RATE & 0x00FF))

//-----------------------------------------------------------------------------
// Pin Definitions
//-----------------------------------------------------------------------------

SBIT (LED, SFR_P1, 3);                 // LED==1 means ON

//-----------------------------------------------------------------------------
// Function Prototypes
//-----------------------------------------------------------------------------

void OSCILLATOR_Init (void);
void PORT_Init (void);
void TIMER0_Init (void);

INTERRUPT_PROTO (TIMER0_ISR, INTERRUPT_TIMER0);

//-----------------------------------------------------------------------------
// main() Routine
//-----------------------------------------------------------------------------

void main (void)
{
   SFRPAGE = ACTIVE_PAGE;              // Set SFRPAGE for PCA0MD

   PCA0MD &= ~0x40;                    // Disable the watchdog timer

   OSCILLATOR_Init ();                 // Configure system clock
   PORT_Init ();                       // Initialize crossbar
   TIMER0_Init ();                     // Initialize Timer0

   EA = 1;                             // Enable global interrupts

   while (1);                          // Spin forever
}

//-----------------------------------------------------------------------------
// Initialization Subroutines
//-----------------------------------------------------------------------------

//-----------------------------------------------------------------------------
// OSCILLATOR_Init
//-----------------------------------------------------------------------------
//
// Return Value:  None
// Parameters:    None
//
// Configure the internal oscillator to maximum internal frequency / 8, which
// is 3 MHz
//
//-----------------------------------------------------------------------------
void OSCILLATOR_Init (void)
{
   U8 SFRPAGE_save = SFRPAGE;
   SFRPAGE = CONFIG_PAGE;

   OSCICN = 0x84;

   SFRPAGE = SFRPAGE_save;
}

//-----------------------------------------------------------------------------
// PORT_Init
//-----------------------------------------------------------------------------
//
// Return Value:  None
// Parameters:    None
//
// Configure the Crossbar and GPIO ports.
//
// P1.3 - digital  push-pull   LED
//
//-----------------------------------------------------------------------------
void PORT_Init (void)
{
   U8 SFRPAGE_save = SFRPAGE;
   SFRPAGE = CONFIG_PAGE;

   P1MDOUT |= 0x08;                    // Enable LED as a push-pull output
   P1SKIP  |= 0x08;                    // Skip the LED pin on the crossbar

   XBR2     = 0x40;                    // Enable crossbar and weak pull-ups

   SFRPAGE = SFRPAGE_save;
}

//-----------------------------------------------------------------------------
// TIMER0_Init
//-----------------------------------------------------------------------------
//
// Return Value:  None
// Parameters:    None
//
// Configure Timer0 to 16-bit Timer mode and generate an interrupt
// every TIMER0_RL Timer0 cycles using SYSCLK/48 as the Timer0 time base.
//
//-----------------------------------------------------------------------------
void TIMER0_Init(void)
{
   // No need to set SFRPAGE as all registers accessed in this function
   // are available on all pages

   TH0 = TIMER0_RL_HIGH;               // Init Timer0 High register
   TL0 = TIMER0_RL_LOW;                // Init Timer0 Low register

   TMOD  = 0x01;                       // Timer0 in 16-bit mode
   CKCON = 0x02;                       // Timer0 uses a 1:48 prescaler
   ET0   = 1;                          // Timer0 interrupt enabled
   TCON  = 0x10;                       // Timer0 ON
}


//-----------------------------------------------------------------------------
// Interrupt Service Routines
//-----------------------------------------------------------------------------

//-----------------------------------------------------------------------------
// TIMER0_ISR
//-----------------------------------------------------------------------------
//
// Process the Timer0 interrupt and toggle the LED
//
//-----------------------------------------------------------------------------
INTERRUPT (TIMER0_ISR, INTERRUPT_TIMER0)
{
   LED = !LED;                         // Toggle the LED
   TH0 = TIMER0_RL_HIGH;               // Reinitialize Timer0 High register
   TL0 = TIMER0_RL_LOW;                // Reinitialize Timer0 Low register
}

//-----------------------------------------------------------------------------
// End Of File
//-----------------------------------------------------------------------------