board_memories.c

本程序是以前程序的升级

//------------------------------------------------------------------------------
/// Initialize and configure the SDRAM for a 48 MHz MCK (ROM code clock settings)
//------------------------------------------------------------------------------
void BOARD_ConfigureSdram48MHz(unsigned char busWidth)
{
    volatile unsigned int i;
    static const Pin pinsSdram[] = {PINS_SDRAM};
    volatile unsigned int *pSdram = (unsigned int *) AT91C_EBI_SDRAM;
    unsigned short sdrc_dbw = 0;

    switch (busWidth) {
        case 16:
            sdrc_dbw = AT91C_SDRAMC_DBW_16_BITS;
            break;

        case 32:
        default:
            sdrc_dbw = AT91C_SDRAMC_DBW_32_BITS;
            break;

    }

    // Enable corresponding PIOs
    PIO_Configure(pinsSdram, 1);

    // Enable EBI chip select for the SDRAM
    WRITE(AT91C_BASE_MATRIX, MATRIX_EBICSA, AT91C_MATRIX_CS1A_SDRAMC);


    // CFG Control Register
    WRITE(AT91C_BASE_SDRAMC, SDRAMC_CR, AT91C_SDRAMC_NC_9
                                        | AT91C_SDRAMC_NR_13
                                        | AT91C_SDRAMC_CAS_2
                                        | AT91C_SDRAMC_NB_4_BANKS
                                        | sdrc_dbw
                                        | AT91C_SDRAMC_TWR_1
                                        | AT91C_SDRAMC_TRC_4
                                        | AT91C_SDRAMC_TRP_1
                                        | AT91C_SDRAMC_TRCD_1
                                        | AT91C_SDRAMC_TRAS_2
                                        | AT91C_SDRAMC_TXSR_3);

    for (i = 0; i < 1000; i++);

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_MR, AT91C_SDRAMC_MODE_NOP_CMD); // Perform NOP
    pSdram[0] = 0x00000000;

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_MR, AT91C_SDRAMC_MODE_PRCGALL_CMD);     // Set PRCHG AL
    pSdram[0] = 0x00000000;                                         // Perform PRCHG

    for (i = 0; i < 10000; i++);

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_MR, AT91C_SDRAMC_MODE_RFSH_CMD);        // Set 1st CBR
    pSdram[1] = 0x00000001;                                         // Perform CBR

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_MR, AT91C_SDRAMC_MODE_RFSH_CMD);        // Set 2 CBR
    pSdram[2] = 0x00000002;                                         // Perform CBR

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_MR, AT91C_SDRAMC_MODE_RFSH_CMD);        // Set 3 CBR
    pSdram[3] = 0x00000003;                                    // Perform CBR

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_MR, AT91C_SDRAMC_MODE_RFSH_CMD);        // Set 4 CBR
    pSdram[4] = 0x00000004;                                   // Perform CBR

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_MR, AT91C_SDRAMC_MODE_RFSH_CMD);        // Set 5 CBR
    pSdram[5] = 0x00000005;                                   // Perform CBR

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_MR, AT91C_SDRAMC_MODE_RFSH_CMD);        // Set 6 CBR
    pSdram[6] = 0x00000006;                                 // Perform CBR

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_MR, AT91C_SDRAMC_MODE_RFSH_CMD);        // Set 7 CBR
    pSdram[7] = 0x00000007;                                 // Perform CBR

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_MR, AT91C_SDRAMC_MODE_RFSH_CMD);        // Set 8 CBR
    pSdram[8] = 0x00000008;                                 // Perform CBR

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_MR, AT91C_SDRAMC_MODE_LMR_CMD);         // Set LMR operation
    pSdram[9] = 0xcafedede;                                 // Perform LMR burst=1, lat=2

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_TR, (48000000 * 7) / 1000000);          // Set Refresh Timer

    WRITE(AT91C_BASE_SDRAMC, SDRAMC_MR, AT91C_SDRAMC_MODE_NORMAL_CMD);      // Set Normal mode
    pSdram[0] = 0x00000000;                                         // Perform Normal mode
}

//------------------------------------------------------------------------------
/// Configures the EBI for NandFlash access. Pins must be configured after or
/// before calling this function.
//------------------------------------------------------------------------------
void BOARD_ConfigureNandFlash(unsigned char busWidth)
{
    // Configure EBI
    AT91C_BASE_MATRIX->MATRIX_EBICSA |= AT91C_MATRIX_CS3A_SM;

    // Configure SMC
    AT91C_BASE_SMC->SMC_SETUP3 = 0x00010001;
    AT91C_BASE_SMC->SMC_PULSE3 = 0x03030303;
    AT91C_BASE_SMC->SMC_CYCLE3 = 0x00050005;
      AT91C_BASE_SMC->SMC_CTRL3  = 0x00020003;
      
    if (busWidth == 8) {

        AT91C_BASE_SMC->SMC_CTRL3 |= AT91C_SMC_DBW_WIDTH_EIGTH_BITS;
    }
    else if (busWidth == 16) {
 
        AT91C_BASE_SMC->SMC_CTRL3 |= AT91C_SMC_DBW_WIDTH_SIXTEEN_BITS;
    }
}

//------------------------------------------------------------------------------
/// Configures the EBI for NandFlash access at 48MHz. Pins must be configured
/// after or before calling this function.
//------------------------------------------------------------------------------
void BOARD_ConfigureNandFlash48MHz(unsigned char busWidth)
{
    // Configure EBI
    AT91C_BASE_MATRIX->MATRIX_EBICSA |= AT91C_MATRIX_CS3A_SM;

    // Configure SMC
    AT91C_BASE_SMC->SMC_SETUP3 = 0x00010001;
    AT91C_BASE_SMC->SMC_PULSE3 = 0x04030302;
    AT91C_BASE_SMC->SMC_CYCLE3 = 0x00070004;
    AT91C_BASE_SMC->SMC_CTRL3  = (AT91C_SMC_READMODE
                                 | AT91C_SMC_WRITEMODE
                                 | AT91C_SMC_NWAITM_NWAIT_DISABLE
                                 | ((0x1 << 16) & AT91C_SMC_TDF));
    
    if (busWidth == 8) {

        AT91C_BASE_SMC->SMC_CTRL3 |= AT91C_SMC_DBW_WIDTH_EIGTH_BITS;
    }
    else if (busWidth == 16) {
 
        AT91C_BASE_SMC->SMC_CTRL3 |= AT91C_SMC_DBW_WIDTH_SIXTEEN_BITS;
    }
}

//------------------------------------------------------------------------------
/// Configures the EBI for NorFlash access
/// \Param busWidth Bus width 
//------------------------------------------------------------------------------
void BOARD_ConfigureNorFlash(unsigned char busWidth)
{
    // Configure SMC

    AT91C_BASE_SMC->SMC_SETUP0 = 0x00000002;
    AT91C_BASE_SMC->SMC_PULSE0 = 0x0A0A0A06;
    AT91C_BASE_SMC->SMC_CYCLE0 = 0x000A000A;
    AT91C_BASE_SMC->SMC_CTRL0  = (AT91C_SMC_READMODE
                                  | AT91C_SMC_WRITEMODE
                                  | AT91C_SMC_NWAITM_NWAIT_DISABLE
                                  | ((0x1 << 16) & AT91C_SMC_TDF));

    if (busWidth == 8) {
        AT91C_BASE_SMC->SMC_CTRL0 |= AT91C_SMC_DBW_WIDTH_EIGTH_BITS;
    }
    else if (busWidth == 16) {
        AT91C_BASE_SMC->SMC_CTRL0 |= AT91C_SMC_DBW_WIDTH_SIXTEEN_BITS;
    }
    else if (busWidth == 32) {
        AT91C_BASE_SMC->SMC_CTRL0 |= AT91C_SMC_DBW_WIDTH_THIRTY_TWO_BITS;
    }
}


//------------------------------------------------------------------------------
/// Configures the EBI for NorFlash access at 48MHz.
/// \Param busWidth Bus width 
//------------------------------------------------------------------------------
void BOARD_ConfigureNorFlash48MHz(unsigned char busWidth)
{
    // Configure SMC
    AT91C_BASE_SMC->SMC_SETUP0 = 0x00000001;
    AT91C_BASE_SMC->SMC_PULSE0 = 0x07070703;
    AT91C_BASE_SMC->SMC_CYCLE0 = 0x00070007;
    AT91C_BASE_SMC->SMC_CTRL0  = (AT91C_SMC_READMODE
                                  | AT91C_SMC_WRITEMODE
                                  | AT91C_SMC_NWAITM_NWAIT_DISABLE
                                  | ((0x1 << 16) & AT91C_SMC_TDF));
                           
    if (busWidth == 8) {

        AT91C_BASE_SMC->SMC_CTRL0 |= AT91C_SMC_DBW_WIDTH_EIGTH_BITS;
    }
    else if (busWidth == 16) {
 
        AT91C_BASE_SMC->SMC_CTRL0 |= AT91C_SMC_DBW_WIDTH_SIXTEEN_BITS;
    }
    else if (busWidth == 32) {
 
        AT91C_BASE_SMC->SMC_CTRL0 |= AT91C_SMC_DBW_WIDTH_THIRTY_TWO_BITS;
    }
}