monitor.c

ssd192X_LPC2210_V2.0 LPC2210的16位数据口控制SSD1926

#include "ssd192X.h"

int LCD_WIDTH=320;
int LCD_HEIGHT=240;
int WIDE_TFT=0;

void lcd_hw_init(void)
{
	int i=0;
	INT32 lcd_hw_init[][2]=
	{
		{REG_PCLK_FREQ_RATIO_0         ,0x13},//0x158
		{REG_PCLK_FREQ_RATIO_1         ,0x0a},//0x159
		{REG_PCLK_FREQ_RATIO_2         ,0x05},//0x15a
		{REG_PANEL_TYPE                ,0x61},//0x10 /*serial tft*/
		{REG_MOD_RATE                  ,0x00},//0x11
		{REG_HORIZ_TOTAL_0             ,0x63},//0x12
		{REG_HORIZ_TOTAL_1             ,0x07},//0x13
		{REG_HDP                       ,0x27},//0x14
		{REG_HDP_START_POS0            ,0xa0},//0x16
		{REG_HDP_START_POS1            ,0x00},//0x17
		{REG_VERT_TOTAL0               ,0x0c},//0x18
		{REG_VERT_TOTAL1               ,0x02},//0x19
		{REG_VDP0                      ,0xef},//0x1C
		{REG_VDP1                      ,0x00},//0x1D
		{REG_VDP_START_POS0            ,0xa5},//0x1e
		{REG_VDP_START_POS1            ,0x00},//0x1f
		{REG_HSYNC_PULSE_WIDTH         ,0xdf},//0x20
		{REG_LLINE_PULSE_START_SUBPIXEL_POS,0x00},//0x21=0pixels
		{REG_HSYNC_PULSE_START_POS0    ,0x92},//0x22
		{REG_HSYNC_PULSE_START_POS1    ,0x02},//0x23
		{REG_VSYNC_PULSE_WIDTH         ,0x81},//0x24
		{REG_VSYNC_PULSE_START_POS0    ,0x22},//0x26
		{REG_VSYNC_PULSE_START_POS1    ,0x00},//0x27
		{REG_FPFRAME_START_OFFSET0	,0x0},//0x30
		{REG_FPFRAME_START_OFFSET1	,0x0},//0x31
		{REG_HRTFT_SPECIAL_OUTPUT	,0x01},//0x38
		{REG_DYN_DITHER_CONTROL,         0x00},	//0x50
		{REG_GPIO_STATUS_CONTROL1	,0x00},//0xac
//		{REG_DISPLAY_MODE 		,0x05},//0x70//default off
		{REG_SPECIAL_EFFECTS,            0x40},//0x71  ** byte swap enable
		{REG_LCD0_Rise_0	        ,0x01},//0x2b0
		{REG_LCD0_Rise_1	        ,0x00},//0x2b1
		{REG_LCD0_Fall_0	        ,0x04},//0x2b4
		{REG_LCD0_Fall_1	        ,0x00},//0x2b5
		{REG_LCD0_Period_0	        ,0x0a},//0x2b8
		{REG_LCD0_Period_0	        ,0x00},//0x2b9
		{REG_LCD0_Ctl_0	        	,0x02},//0x2bc
		{REG_DEFINE_END				,0x00}//0xFFFF
	};

	debug("Init monitor QVGA (320RGBx240).\n");
	while(lcd_hw_init[i][0]!=REG_DEFINE_END)
	{
		SSD_REGWB(lcd_hw_init[i][0],lcd_hw_init[i][1]);
		i++;
        }
}