fet140_dma_10.s43

MSP430汇编语言官方源代码。入门级学习资料！

;******************************************************************************
;  MSP-FET430P140 Demo - DMA0, ADC12 A10 Block Xfer to Flash, TBCCR1, DCO
;
;  Description: A 0x20 word block of data is sampled and recorded into Flash
;  from the ADC12 channel 10 the integrated temperature sensor using the
;  Record() function. Timer_B CCR1 begins the ADC12 sample period, CCR0 the hold
;  and conversion start. Timer_B operates in the up mode with CCR0 defining the
;  sample period. DMA0 will automatically transfer each ADC12 conversion code
;  to memory when complete. At the end of the recording block, DMA0 will issue
;  an interrupt existing the function.
;  In this example the ADC12 sample period is 100 SMCLK cycle, and Flash
;  programming requires 70 cycles.
;  In the example the Flash block use to record the ADC12 data begins at 0x1080.
;  P1.0 is toggled during DMA transfer only for demonstration purposes.
;  ACLK = n/a, MCLK = SMCLK = default DCO ~ 800k
;  //* Set Breakpoint on NOP in the Mainloop to avoid Stressing Flash *//	
;  //* MSP430F169 Device Required *//
;
;               MSP430F169
;            -----------------
;        /|\|              XIN|-
;         | |                 |
;         --|RST          XOUT|-
;           |                 |
;           |A10          P1.0|-->LED
;
;
;   H. Grewal
;   Texas Instruments Inc.
;   Feb 2005
;   Built with IAR Embedded Workbench Version: 3.21A
;******************************************************************************
#include  <msp430x16x.h>
;------------------------------------------------------------------------------
            ORG     01100h                  ; Progam Start
;------------------------------------------------------------------------------
RESET       mov.w   #0A00h,SP               ; Initialize stackpointer
StopWDT     mov.w   #WDTPW+WDTHOLD,&WDTCTL  ; Stop watchdog timer
            mov     #FWKEY+FSSEL_2+FN0,&FCTL2 ; Clk src = SMCLK / 2 (~400KHz)
            bis.b   #01h,&P1DIR             ; Set P1.0 to output direction
Mainloop    call    #record
                    nop                     ; Needed only for debugger
            jmp     Mainloop
record      mov.w   #01080h,R5              ;
            mov.w   #FWKEY+ERASE,&FCTL1     ; Erase bit = 1
Erase_SegA  mov.w   #FWKEY,&FCTL3           ; Lock = 0
            mov.w   #0,&01080h              ; Dummy write to erase Flash segment
            mov.b   #SREF_1+INCH_10,&ADC12MCTL0 ; Channel A10, Vref+
            mov     #0h,&ADC12IFG
            mov     #SHS_3+CONSEQ_2,&ADC12CTL1 ; S&H TB.OUT1, rep. single chan
            mov.w   #REF2_5V+REFON+ADC12ON+ENC,&ADC12CTL0 ; VRef ADC12 on, enabled
            mov     #03600h,R15             ; Delay for needed ref start-up.
L$1         dec     R15                     ; See datasheet for details.
            jnz     L$1                     ;
            mov     #100,&TBCCR0            ; Init TBCCR0 w/ sample prd
            mov     #70,&TBCCR1             ; Trigger for ADC12 SC
            mov     #OUTMOD_7,&TBCCTL1      ; Reset OUT1 on EQU1, set on EQU0
SetupDMAx   mov.w   #ADC12MEM0_,&DMA0SA     ; Src address = ADC12 module
            mov.w   #1080h,&DMA0DA          ; Dst address = RAM memory
            mov.w   #020h,&DMA0SZ           ; Size in words
            mov.w   #DMA0TSEL_6,&DMACTL0    ; ADC12IFGx triggers DMA0
            mov.w   #DMAONFETCH,&DMACTL1    ; Required for proper Flash Write
            mov.w   #DMADSTINCR_3+DMAIE+DMAEN,&DMA0CTL; Config
            bis.b   #01h,&P1OUT             ; Start recording and enter LPM0
            mov     #TBSSEL_2+MC_1+TBCLR,&TBCTL ;SMCLK, clear TBR, up mode
            mov.w   #FWKEY+WRT,&FCTL1       ; Write bit = 1
            bis.b   #CPUOFF+GIE,SR          ; Enter LPM0, enable interrupts
            mov.w   #FWKEY,&FCTL1           ; Write bit = 0
            mov.w   #FWKEY+LOCK,&FCTL3      ; Lock = 1
            bic     #CONSEQ_2,&ADC12CTL1    ; Stop conversion immediately
            bic     #ENC,&ADC12CTL0         ; Disable ADC12 conversion
            mov     #0h, &ADC12CTL0         ; Switch off ADC12 & ref voltage
            mov     #0h, &TBCTL             ; Disable Timer_B
            bic.b   #01h,&P1OUT             ; Clear P1.0 (LED Off)
            ret
;------------------------------------------------------------------------------
DMA_ISR;    Common ISR for DMA/DAC12
;------------------------------------------------------------------------------
            bic     #DMAIFG,&DMA0CTL        ; Clear DMA0 interrupt flag
            bic     #LPM0,0(SP)             ; Exit LPMx, interrupts enabled
            reti                            ;
;------------------------------------------------------------------------------
;           Interrupt Vectors
;------------------------------------------------------------------------------
             ORG     0FFFEh                  ; POR, ext. Reset, Watchdog, Flash
             DW      RESET                   ;
             ORG     0FFE0h                  ; DMA Vector
             DW      DMA_ISR                 ;
             END