rfc1413.txt

来自「中、英文RFC文档大全打包下载完全版 .」· 文本 代码 · 共 451 行 · 第 1/2 页

Network Working Group                                       M. St. Johns
Request for Comments: 1413                      US Department of Defense
Obsoletes: 931                                             February 1993


                        Identification Protocol

Status of this Memo

   This RFC specifies an IAB standards track protocol for the Internet
   community, and requests discussion and suggestions for improvements.
   Please refer to the current edition of the "IAB Official Protocol
   Standards" for the standardization state and status of this protocol.
   Distribution of this memo is unlimited.

1.  INTRODUCTION

   The Identification Protocol (a.k.a., "ident", a.k.a., "the Ident
   Protocol") provides a means to determine the identity of a user of a
   particular TCP connection.  Given a TCP port number pair, it returns
   a character string which identifies the owner of that connection on
   the server's system.

   The Identification Protocol was formerly called the Authentication
   Server Protocol.  It has been renamed to better reflect its function.
   This document is a product of the TCP Client Identity Protocol
   Working Group of the Internet Engineering Task Force (IETF).

2.  OVERVIEW

   This is a connection based application on TCP.  A server listens for
   TCP connections on TCP port 113 (decimal).  Once a connection is
   established, the server reads a line of data which specifies the
   connection of interest.  If it exists, the system dependent user
   identifier of the connection of interest is sent as the reply.  The
   server may then either shut the connection down or it may continue to
   read/respond to multiple queries.

   The server should close the connection down after a configurable
   amount of time with no queries - a 60-180 second idle timeout is
   recommended.  The client may close the connection down at any time;
   however to allow for network delays the client should wait at least
   30 seconds (or longer) after a query before abandoning the query and
   closing the connection.







St. Johns                                                       [Page 1]

RFC 1413                Identification Protocol            February 1993


3.  RESTRICTIONS

   Queries are permitted only for fully specified connections.  The
   query contains the local/foreign port pair -- the local/foreign
   address pair used to fully specify the connection is taken from the
   local and foreign address of query connection.  This means a user on
   address A may only query the server on address B about connections
   between A and B.

4.  QUERY/RESPONSE FORMAT

   The server accepts simple text query requests of the form:

            <port-on-server> , <port-on-client>

   where <port-on-server> is the TCP port (decimal) on the target (where
   the "ident" server is running) system, and <port-on-client> is the
   TCP port (decimal) on the source (client) system.

   N.B - If a client on host A wants to ask a server on host B about a
   connection specified locally (on the client's machine) as 23, 6191
   (an inbound TELNET connection), the client must actually ask about
   6191, 23 - which is how the connection would be specified on host B.

      For example:

                 6191, 23

   The response is of the form

   <port-on-server> , <port-on-client> : <resp-type> : <add-info>

   where <port-on-server>,<port-on-client> are the same pair as the
   query, <resp-type> is a keyword identifying the type of response, and
   <add-info> is context dependent.

   The information returned is that associated with the fully specified
   TCP connection identified by <server-address>, <client-address>,
   <port-on-server>, <port-on-client>, where <server-address> and
   <client-address> are the local and foreign IP addresses of the
   querying connection -- i.e., the TCP connection to the Identification
   Protocol Server.  (<port-on-server> and <port-on-client> are taken
   from the query.)

      For example:

         6193, 23 : USERID : UNIX : stjohns
         6195, 23 : ERROR : NO-USER



St. Johns                                                       [Page 2]

RFC 1413                Identification Protocol            February 1993


5.  RESPONSE TYPES

A response can be one of two types:

USERID

     In this case, <add-info> is a string consisting of an
     operating system name (with an optional character set
     identifier), followed by ":", followed by an
     identification string.

     The character set (if present) is separated from the
     operating system name by ",".  The character set
     identifier is used to indicate the character set of the
     identification string.  The character set identifier,
     if omitted, defaults to "US-ASCII" (see below).

     Permitted operating system names and character set
     names are specified in RFC 1340, "Assigned Numbers" or
     its successors.

     In addition to those operating system and character set
     names specified in "Assigned Numbers" there is one
     special case operating system identifier - "OTHER".

     Unless "OTHER" is specified as the operating system
     type, the server is expected to return the "normal"
     user identification of the owner of this connection.
     "Normal" in this context may be taken to mean a string
     of characters which uniquely identifies the connection
     owner such as a user identifier assigned by the system
     administrator and used by such user as a mail
     identifier, or as the "user" part of a user/password
     pair used to gain access to system resources.  When an
     operating system is specified (e.g., anything but
     "OTHER"), the user identifier is expected to be in a
     more or less immediately useful form - e.g., something
     that could be used as an argument to "finger" or as a
     mail address.

     "OTHER" indicates the identifier is an unformatted
     character string consisting of printable characters in
     the specified character set.  "OTHER" should be
     specified if the user identifier does not meet the
     constraints of the previous paragraph.  Sending an
     encrypted audit token, or returning other non-userid
     information about a user (such as the real name and
     phone number of a user from a UNIX passwd file) are



St. Johns                                                       [Page 3]

RFC 1413                Identification Protocol            February 1993


     both examples of when "OTHER" should be used.

     Returned user identifiers are expected to be printable
     in the character set indicated.

     The identifier is an unformatted octet string - - all
     octets are permissible EXCEPT octal 000 (NUL), 012 (LF)
     and 015 (CR).  N.B. - space characters (040) following the
     colon separator ARE part of the identifier string and
     may not be ignored. A response string is still
     terminated normally by a CR/LF.  N.B. A string may be
     printable, but is not *necessarily* printable.

ERROR

   For some reason the port owner could not be determined, <add-info>
   tells why.  The following are the permitted values of <add-info> and
   their meanings:

          INVALID-PORT

          Either the local or foreign port was improperly
          specified.  This should be returned if either or
          both of the port ids were out of range (TCP port
          numbers are from 1-65535), negative integers, reals or
          in any fashion not recognized as a non-negative
          integer.

          NO-USER

          The connection specified by the port pair is not
          currently in use or currently not owned by an
          identifiable entity.

          HIDDEN-USER

          The server was able to identify the user of this
          port, but the information was not returned at the
          request of the user.

          UNKNOWN-ERROR

          Can't determine connection owner; reason unknown.
          Any error not covered above should return this
          error code value.  Optionally, this code MAY be
          returned in lieu of any other specific error code
          if, for example, the server desires to hide
          information implied by the return of that error



St. Johns                                                       [Page 4]