hal_board.h

cc2x30_sw_examples: 适用于SmartRF05EB 支持CC2430、CC2530 提供Light_Switch及perTest例程。

/*******************************************************************************

  Filename:     hal_board.h

  Description:  SmartRF05 board with CCxxxxEM.

*******************************************************************************/

#ifndef HAL_BOARD_H
#define HAL_BOARD_H

#if (chip==2430)
#include "ioCC2430.h"
#elif (chip==2431)
#include "ioCC2431.h"
#elif (chip==2530 || chip==2531)
#include "ioCC2530.h"
#elif (chip==2510)
#include "ioCC2510.h"
#elif (chip==2511)
#include "ioCC2511.h"
#else
#error "Chip not supported!"
#endif

#include "hal_cc8051.h"
#include "hal_defs.h"
#include "hal_mcu.h"

/*******************************************************************************
 * CONSTANTS
 */

#define BOARD_NAME                     "SRF05"

// SPI
#define HAL_BOARD_IO_SPI_MISO_PORT     1
#define HAL_BOARD_IO_SPI_MISO_PIN      7
#define HAL_BOARD_IO_SPI_MOSI_PORT     1
#define HAL_BOARD_IO_SPI_MOSI_PIN      6
#define HAL_BOARD_IO_SPI_CLK_PORT      1
#define HAL_BOARD_IO_SPI_CLK_PIN       5
#define HAL_BOARD_IO_EM_CS_PORT        1
#define HAL_BOARD_IO_EM_CS_PIN         4

// LCD
#define HAL_BOARD_IO_LCD_CS_PORT       1
#define HAL_BOARD_IO_LCD_CS_PIN        2
#define HAL_BOARD_IO_LCD_MODE_PORT     0
#define HAL_BOARD_IO_LCD_MODE_PIN      0
#define HAL_BOARD_IO_LCD_RST_PORT      1
#define HAL_BOARD_IO_LCD_RST_PIN       1

// LEDs
#define HAL_BOARD_IO_LED_1_PORT             1   // Green
#define HAL_BOARD_IO_LED_1_PIN              0
// LED2, LED3 and LED4 are not connected to CC2430


// Buttons
#define HAL_BOARD_IO_BTN_1_PORT             0   // Button S1
#define HAL_BOARD_IO_BTN_1_PIN              1

// Potmeter
#define HAL_POTMETER_ADC_PORT               0
#define HAL_POTMETER_ADC_CH                 7

// Joystick
#define HAL_BOARD_IO_JOYSTICK_ADC_PORT      0
#define HAL_BOARD_IO_JOYSTICK_ADC_PIN       6
#define HAL_BOARD_IO_JOY_MOVE_PORT          2
#define HAL_BOARD_IO_JOY_MOVE_PIN           0

// UART
#define HAL_BOARD_IO_UART_RTS_PORT          0
#define HAL_BOARD_IO_UART_RTS_PIN           5


// Debounce
#define HAL_DEBOUNCE(expr)    { int i; for (i=0; i<500; i++) { if (!(expr)) i = 0; } }

/*******************************************************************************
 * MACROS
 */

// LED
#define HAL_LED_SET_1() MCU_IO_SET_HIGH(HAL_BOARD_IO_LED_1_PORT, \
    HAL_BOARD_IO_LED_1_PIN)

#define HAL_LED_CLR_1() MCU_IO_SET_LOW(HAL_BOARD_IO_LED_1_PORT, \
    HAL_BOARD_IO_LED_1_PIN)

#define HAL_LED_TGL_1() MCU_IO_TGL(HAL_BOARD_IO_LED_1_PORT, \
    HAL_BOARD_IO_LED_1_PIN)



// Buttons
#ifdef SRF05EB_VERSION_1_3
#define HAL_BUTTON_1_PUSHED() (!MCU_IO_GET(HAL_BOARD_IO_BTN_1_PORT, \
    HAL_BOARD_IO_BTN_1_PIN))
#else
#define HAL_BUTTON_1_PUSHED() (MCU_IO_GET(HAL_BOARD_IO_BTN_1_PORT, \
    HAL_BOARD_IO_BTN_1_PIN))
#endif

// Joystick
#define HAL_JOYSTICK_LEVEL()  (MCU_IO_GET(HAL_BOARD_IO_JOYSTICK_ADC_PORT, \
    HAL_BOARD_IO_JOYSTICK_ADC_CH_PIN)

#define HAL_JOYSTICK_UP() ( halJoystickGetDir()==HAL_JOYSTICK_EVT_UP )
#define HAL_JOYSTICK_DOWN() ( halJoystickGetDir()==HAL_JOYSTICK_EVT_DOWN )
#define HAL_JOYSTICK_LEFT() ( halJoystickGetDir()==HAL_JOYSTICK_EVT_LEFT )
#define HAL_JOYSTICK_RIGHT() ( halJoystickGetDir()==HAL_JOYSTICK_EVT_RIGHT )

// UART RTS
#define HAL_RTS_SET()       MCU_IO_SET_HIGH(HAL_BOARD_IO_UART_RTS_PORT, \
    HAL_BOARD_IO_UART_RTS_PIN)
#define HAL_RTS_CLR()       MCU_IO_SET_LOW(HAL_BOARD_IO_UART_RTS_PORT, \
    HAL_BOARD_IO_UART_RTS_PIN)
#define HAL_RTS_DIR_OUT()   MCU_IO_OUTPUT(HAL_BOARD_IO_UART_RTS_PORT, \
    HAL_BOARD_IO_UART_RTS_PIN, 1)


// LCD SPI interface control
#define LCD_SPI_BEGIN()            MCU_IO_SET_LOW(HAL_BOARD_IO_LCD_CS_PORT, HAL_BOARD_IO_LCD_CS_PIN)
#define LCD_SPI_TX(x)              st( U1CSR &= ~0x02; U1DBUF = x; )
#define LCD_SPI_RX()               U1DBUF
#define LCD_SPI_WAIT_RXRDY()       st( while((U1CSR & 0x02) != 0x02); )
#define LCD_SPI_END()              st( NOP(); NOP(); NOP(); NOP(); \
                                       MCU_IO_SET_HIGH(HAL_BOARD_IO_LCD_CS_PORT, HAL_BOARD_IO_LCD_CS_PIN); )

// LCD pin control
#define LCD_DO_WRITE()             MCU_IO_SET_HIGH(HAL_BOARD_IO_LCD_MODE_PORT, HAL_BOARD_IO_LCD_MODE_PIN)
#define LCD_DO_CONTROL()           MCU_IO_SET_LOW(HAL_BOARD_IO_LCD_MODE_PORT, HAL_BOARD_IO_LCD_MODE_PIN)
#define LCD_ACTIVATE_RESET()       MCU_IO_SET_LOW(HAL_BOARD_IO_LCD_RST_PORT, HAL_BOARD_IO_LCD_RST_PIN)
#define LCD_RELEASE_RESET()        MCU_IO_SET_HIGH(HAL_BOARD_IO_LCD_RST_PORT, HAL_BOARD_IO_LCD_RST_PIN)

// Port initialization
#define LCD_CTRL_INIT_PORTS()      st( MCU_IO_OUTPUT(HAL_BOARD_IO_LCD_CS_PORT, HAL_BOARD_IO_LCD_CS_PIN, 1); \
                                       MCU_IO_OUTPUT(HAL_BOARD_IO_LCD_MODE_PORT, HAL_BOARD_IO_LCD_MODE_PIN, 1); \
                                       MCU_IO_OUTPUT(HAL_BOARD_IO_LCD_RST_PORT, HAL_BOARD_IO_LCD_RST_PIN, 1); )


/*******************************************************************************
 * FUNCTION PROTOTYPES
 */
void halBoardInit(void);
void halLcdSpiInit(void);
void halLcdSpiEna(void);
void halLcdSpiDis(void);

#endif

/*------------------------------------------------------------------------------
										  0ooo                                     
								ooo0	 (	 )                                     
								(	)	  ) /                                      
								 \ (	 (_/                                       
								  \_)		 Modify By:cuiqingwei [gary]                  
------------------------------------------------------------------------------*/