f2xx_ports_switchled.c

芯科原厂所有c8051fxx程序的例子。

//-----------------------------------------------------------------------------
// F2xx_Ports_SwitchLED.c
//-----------------------------------------------------------------------------
// Copyright 2005 Silicon Laboratories, Inc.
// http://www.silabs.com
//
// Program Description:
//
// This program demonstrates how to configure port pins as digital inputs
// and outputs.  The C8051F206 target board has one push-button switch 
// connected to a port pin and one LED.  The program constantly checks the 
// status of the switch and if it is pushed, it turns on the LED.
//
//
// How To Test:
//
// 1) Download code to a 'F206 target board
// 2) Ensure that the P2.5 and LED headers are shorted
// 3) Push the button (P2.5) and see that the LED turns on 
//
//
// FID:            2XX000002
// Target:         C8051F2XX
// Tool chain:     Keil C51 7.50 / Keil EVAL C51
// Command Line:   None
//
// Release 1.0
//    -Initial Revision (GP)
//    -15 NOV 2005
//

//-----------------------------------------------------------------------------
// Includes
//-----------------------------------------------------------------------------

#include <c8051f200.h>                 // SFR declarations

//-----------------------------------------------------------------------------
// Pin Declarations
//-----------------------------------------------------------------------------

sbit LED1    = P2^4;                   // LED1 ='0' means ON
sbit SW1     = P2^5;                   // SW1 ='0' means switch pressed

//-----------------------------------------------------------------------------
// Function Prototypes
//-----------------------------------------------------------------------------

void OSCILLATOR_Init (void);           
void PORT_Init (void);

//-----------------------------------------------------------------------------
// main() Routine
//-----------------------------------------------------------------------------

void main (void)
{
   WDTCN = 0xde;                       // Disable watchdog timer
   WDTCN = 0xad;

   PORT_Init();                        // Initialize Port I/O
   OSCILLATOR_Init ();                 // Initialize Oscillator
  
   while (1)
   {
      if (SW1 == 0)                    // If switch depressed
      { 
         LED1 = 0;                     // Turn on LED
      }
	  else   
      {  
         LED1 = 1;                     // Else, turn it off
      }                                	      
   }                                   // End of while(1)
}                                      // End of main()

//-----------------------------------------------------------------------------
// Initialization Subroutines
//-----------------------------------------------------------------------------

//-----------------------------------------------------------------------------
// OSCILLATOR_Init
//-----------------------------------------------------------------------------
//
// Return Value : None
// Parameters   : None
//
// This function initializes the system clock to use the internal oscillator
// at its maximum frequency.
//
//-----------------------------------------------------------------------------
void OSCILLATOR_Init (void)
{
   OSCICN |= 0x03;                     // Configure internal oscillator for
                                       // its maximum frequency (24.5 Mhz)
}

//-----------------------------------------------------------------------------
// PORT_Init
//-----------------------------------------------------------------------------
//
// Return Value : None
// Parameters   : None
//
// This function configures the crossbar and ports pins.
// 
// To configure a pin as a digital input, the pin is configured as digital
// and open-drain and the port latch should be set to a '1'.  The weak-pullups
// are used to pull the pins high.  Pressing the switch pulls the pins low.
//
// To configure a pin as a digital output, the pin is configured as digital
// and push-pull.  
//
// Some ports pins do not have the option to be configured as analog or digital,
// so it not necessary to explicitly configure them as digital.
//
// An output pin can also be configured to be an open-drain output if system
// requires it.  For example, if the pin is an output on a multi-device bus,
// it will probably be configured as an open-drain output instead of a 
// push-pull output.  For the purposes of this example, the pin is configured
// as push-pull output because the pin in only connected to an LED.
//
// P2.4   digital   push-pull     LED1
// P2.5   digital   open-drain    Switch 1
//-----------------------------------------------------------------------------
void PORT_Init (void)
{
   PRT2CF  = 0x10;                     // P2.4 is push-pull
                                       // P2.5 is open-drain

   P2MODE  = 0xFF;                     // P2.4 and P2.5 are digital

   PRT2MX  = 0xA0;                     // Enable global and P2 weak-pullups

   P2     |= 0x20;                     // Set P2.5 latch to '1'
}


//-----------------------------------------------------------------------------
// End Of File
//-----------------------------------------------------------------------------