📄 splc501driver_io.lst
字号:
Sunplus u'nSP Assembler - Ver. 1.14.3.1
Listing File Has Been Relocated
//***************************************************************************//
//文件描述：SPLC501底层驱动程序，主要包括对液晶的IO口初始化、写指令、写数据、
//读数据，以及西文ASCII表数据
//声明： 小丑 20050518 Sunnorth Mz Design
//
//
//***************************************************************************//
.include SPLC501Driver_IO.inc
< //.include hardware.inc
< .DEFINE P_IOA_Data 0x7000 // Write Data into data register and read from IOA pad
< .DEFINE P_IOA_Buffer 0x7001 // Write Data into buffer register and read from buffer register
< .DEFINE P_IOA_Dir 0x7002 // Direction vector for IOA
< .DEFINE P_IOA_Attrib 0x7003 // Attribute vector for IOA
< .DEFINE P_IOA_Latch 0x7004 // Latch PortA data for key change wake-up
<
< .DEFINE P_IOB_Data 0x7005 // Write Data into the data register and read from IOB pad
< .DEFINE P_IOB_Buffer 0x7006 // Write Data into buffer register and read from buffer register
< .DEFINE P_IOB_Dir 0x7007 // Direction vector for IOB
< .DEFINE P_IOB_Attrib 0x7008 // Attribute vector for IOB
< //.define DATA_PORT_HIGHT 0x00 //数据口输出高八位定义，若数据接口为IO端口的高八位，则不屏蔽
< .define M_IO_DATA_MASK 0x00ff //若数据口为高八位，则定义值为0xff00
<
< //.define M_IO_EP 0x0020 //EP与SPCE061A的接口定义
< //.define M_IO_RW 0x0010 //RW与SPCE061A的接口定义
< //.define M_IO_AO 0x0002 //AO与SPCE061A的接口定义
< //.define M_IO_CS 0x0001 //CS与SPCE061A的接口定义
< .define M_IO_EP 0x0020 //EP与SPCE061A的接口定义
< .define M_IO_RW 0x0010 //RW与SPCE061A的接口定义
< .define M_IO_AO 0x0008 //AO与SPCE061A的接口定义
< .define M_IO_CS 0x0004 //CS与SPCE061A的接口定义
<
<
< .define P_IO_Data_D P_IOA_Data
< .define P_IO_Data_A P_IOA_Attrib
< .define P_IO_Data_Di P_IOA_Dir
< .define P_IO_Data P_IO_Data_D
< .define P_IO_Data_B P_IOA_Buffer
<
< .define P_IO_Ctrl_D P_IOB_Data
< .define P_IO_Ctrl_A P_IOB_Attrib
< .define P_IO_Ctrl_Di P_IOB_Dir
< .define P_IO_Ctrl_B P_IOB_Buffer
< .define P_IO_Ctrl P_IO_Ctrl_D
00000000 .ram
0000BE13 .code
//***************************************************************************//
//程序：F_SPLC501_Initial_IO()
//描述：SPLC501接口的初始化程序 C语言调用，汇编语言调用
//参数：无
//声明：小丑 20050518 sunnorth Mz Design
//注意：破坏R1寄存器，保护R1
//***************************************************************************//
.public _F_SPLC501_Initial_IO
_F_SPLC501_Initial_IO:
F_SPLC501_Initial_IO:
0000BE13 88 D2 push r1 to [sp]
0000BE14 11 93 02 70 r1 = [P_IO_Data_Di]
0000BE16 09 A3 FF 00 r1 |= M_IO_DATA_MASK
0000BE18 19 D3 02 70 [P_IO_Data_Di] = r1
0000BE1A 11 93 03 70 r1 = [P_IO_Data_A]
0000BE1C 09 A3 FF 00 r1 |= M_IO_DATA_MASK
0000BE1E 19 D3 03 70 [P_IO_Data_A] = r1
0000BE20 11 93 01 70 r1 = [P_IO_Data_B]
0000BE22 09 A3 FF 00 r1 |= M_IO_DATA_MASK
0000BE24 19 D3 00 70 [P_IO_Data_D] = r1
0000BE26 11 93 07 70 r1 = [P_IO_Ctrl_Di]
0000BE28 7C A2 r1 |= (M_IO_EP+M_IO_AO+M_IO_RW+M_IO_CS)
0000BE29 19 D3 07 70 [P_IO_Ctrl_Di] = r1
0000BE2B 11 93 08 70 r1 = [P_IO_Ctrl_A]
0000BE2D 7C A2 r1 |= (M_IO_EP+M_IO_AO+M_IO_RW+M_IO_CS)
0000BE2E 19 D3 08 70 [P_IO_Ctrl_A] = r1
0000BE30 11 93 06 70 r1 = [P_IO_Ctrl_B]
0000BE32 09 A3 C3 FF r1 |= ~(M_IO_EP+M_IO_AO+M_IO_RW+M_IO_CS)
0000BE34 19 D3 05 70 [P_IO_Ctrl_D] = r1
0000BE36 88 90 pop r1 from [sp]
0000BE37 90 9A retf
//***************************************************************************//
//程序：F_SPLC501_Write_Com()
//描述：往SPLC501里写一个字节指令 C语言调用，汇编语言调用
//参数：r1送入要传送的指令
//声明：小丑 20050518 sunnorth Mz Design
//注意：破坏R1寄存器，保护R2、R5寄存器
//***************************************************************************//
.public _F_SPLC501_Write_Com
_F_SPLC501_Write_Com:
F_SPLC501_Write_Com:
0000BE38 90 D6 push r2,r3 to [sp]
0000BE39 88 DA push r5 to [sp]
0000BE3A 12 95 06 70 r2 = [P_IO_Ctrl_B] //得到IOB口的状态
0000BE3C 0A B5 DB FF r2 &= ~(M_IO_EP+M_IO_CS) //EP CS to Low 20050613 Edit by xinqiang
0000BE3E 1A D5 06 70 [P_IO_Ctrl_B] = r2 //EP Low
0000BE40 12 95 06 70 r2 = [P_IO_Ctrl_B]
0000BE42 0A B5 E7 FF r2 &= ~(M_IO_AO+M_IO_RW)
0000BE44 1A D5 06 70 [P_IO_Ctrl_B] = r2 //AO RW Low
.ifdef DATA_PORT_HIGHT
r1 = r1 lsl 4
r1 = r1 lsl 4
.endif
0000BE46 13 97 01 70 r3 = [P_IO_Data_B]
0000BE48 0B B7 00 FF r3 &= ~M_IO_DATA_MASK
0000BE4A 09 B3 FF 00 r1 &= M_IO_DATA_MASK //Get Low Data Command
0000BE4C 03 03 r1 = r1+r3
0000BE4D 19 D3 00 70 [P_IO_Data] = r1 //往数据口送数据
0000BE4F 00 EE nop
0000BE50 60 A4 r2 |= M_IO_EP //EP to Hight
0000BE51 1A D5 05 70 [P_IO_Ctrl] = r2
0000BE53 00 EE nop
0000BE54 0A B5 DF FF r2 &= ~M_IO_EP //EP to Low
0000BE56 44 A4 r2 |= M_IO_CS //CS to hight 20050613 Edit by xinqiang
0000BE57 1A D5 05 70 [P_IO_Ctrl] = r2
0000BE59 88 98 pop r5 from [sp]
0000BE5A 90 92 pop r2,r3 from [sp]
0000BE5B 90 9A retf
//***************************************************************************//
//程序：F_SPLC501_Write_Data()
//描述：往SPLC501里写一个字节数据 C语言调用，汇编语言调用
//参数：r1送入要传送的数据
//声明：小丑 20050518 sunnorth Mz Design
//注意：破坏R1寄存器，保护R2、R5寄存器
//***************************************************************************//
.public _F_SPLC501_Write_Data
_F_SPLC501_Write_Data:
F_SPLC501_Write_Data:
0000BE5C 88 D4 push r2 to [sp]
0000BE5D 12 95 06 70 r2 = [P_IO_Ctrl_B] //得到IOB口的状态
0000BE5F 0A B5 DB FF r2 &= ~(M_IO_EP+M_IO_CS) //EP CS to Low 20050613 Editby xinqiang
0000BE61 1A D5 06 70 [P_IO_Ctrl_B] = r2 //EP Low
0000BE63 12 95 06 70 r2 = [P_IO_Ctrl_B]
0000BE65 48 A4 r2 |= M_IO_AO
0000BE66 0A B5 EF FF r2 &= ~(M_IO_RW)
0000BE68 1A D5 06 70 [P_IO_Ctrl_B] = r2 //AO Hight, RW Low
.ifdef DATA_PORT_HIGHT
r1 = r1 lsl 4
r1 = r1 lsl 4
.endif
0000BE6A 13 97 01 70 r3 = [P_IO_Data_B]
0000BE6C 0B B7 00 FF r3 &= ~M_IO_DATA_MASK
0000BE6E 09 B3 FF 00 r1 &= M_IO_DATA_MASK //Get Low Data Command
0000BE70 03 03 r1 = r1+r3
0000BE71 19 D3 00 70 [P_IO_Data] = r1 //往数据口送数据
0000BE73 00 EE nop
0000BE74 60 A4 r2 |= M_IO_EP //EP to Hight
0000BE75 1A D5 05 70 [P_IO_Ctrl] = r2
0000BE77 00 EE nop
0000BE78 0A B5 DF FF r2 &= ~M_IO_EP //EP to Low
0000BE7A 44 A4 r2 |= M_IO_CS //CS to Hight 20050613 Editby xinqiag
0000BE7B 1A D5 05 70 [P_IO_Ctrl] = r2
0000BE7D 88 92 pop r2 from [sp]
0000BE7E 90 9A retf
//***************************************************************************//
//程序：F_SPLC501_Read_Data()
//描述：从SPLC501里读一个字节数据 C语言调用，汇编语言调用
//参数：r1输出传送的数据
//声明：小丑 20050518 sunnorth Mz Design
//注意：破坏R1寄存器，保护R2、R5寄存器
//***************************************************************************//
.public _F_SPLC501_Read_Data
.public F_SPLC501_Read_Data
_F_SPLC501_Read_Data:
F_SPLC501_Read_Data:
0000BE7F 40 F0 84 BE call F_SPLC501_Read_Data1
0000BE81 40 F0 84 BE call F_SPLC501_Read_Data1
0000BE83 90 9A retf
F_SPLC501_Read_Data1:
0000BE84 88 D4 push r2 to [sp]
0000BE85 12 95 02 70 r2 = [P_IO_Data_Di] //设置数据口为输入
0000BE87 0A B5 00 FF r2 &= ~M_IO_DATA_MASK
0000BE89 1A D5 02 70 [P_IO_Data_Di] = r2
0000BE8B 12 95 06 70 r2 = [P_IO_Ctrl_B] //得到IOB口的状态
0000BE8D 0A B5 DB FF r2 &= ~(M_IO_EP+M_IO_CS) //EP CS to Low 20050613 Editby xinqiang
0000BE8F 1A D5 06 70 [P_IO_Ctrl_B] = r2 //EP Low
0000BE91 58 A4 r2 |= (M_IO_AO+M_IO_RW)
0000BE92 1A D5 06 70 [P_IO_Ctrl_B] = r2 //AO Hight, RW Hight
0000BE94 00 EE nop
0000BE95 60 A4 r2 |= M_IO_EP
0000BE96 1A D5 06 70 [P_IO_Ctrl_B] = r2 //产生EP高电平，
0000BE98 00 EE nop
0000BE99 0A B5 DF FF r2 &= ~M_IO_EP //EP to Low
0000BE9B 1A D5 05 70 [P_IO_Ctrl] = r2
0000BE9D 11 93 00 70 r1 = [P_IO_Data]
0000BE9F 09 B3 FF 00 r1 &= M_IO_DATA_MASK
0000BEA1 44 A4 r2 |= M_IO_CS
0000BEA2 1A D5 05 70 [P_IO_Ctrl] = r2
0000BEA4 12 95 02 70 r2 = [P_IO_Data_Di] //恢复数据口为输出状态
0000BEA6 0A A5 FF 00 r2 |= M_IO_DATA_MASK
0000BEA8 1A D5 02 70 [P_IO_Data_Di] = r2
.ifdef DATA_PORT_HIGHT
r1 = r1 lsr 4
r1 = r1 lsr 4
.endif
0000BEAA 88 92 pop r2 from [sp]
0000BEAB 90 9A retf
//***************************************************************************//
//程序：F_SPLC501_Read_Status()
//描述：从SPLC501里读状态字数据 C语言调用，汇编语言调用
//参数：r1输出传送的数据
//声明：小丑 20050518 sunnorth Mz Design
//注意：破坏R1寄存器，保护R2寄存器
//***************************************************************************//
.public _F_SPLC501_Read_Status
.public F_SPLC501_Read_Status
_F_SPLC501_Read_Status:
F_SPLC501_Read_Status:
0000BEAC 88 D4 push r2 to [sp]
0000BEAD 12 95 02 70 r2 = [P_IO_Data_Di] //设置数据口为输入
0000BEAF 0A B5 00 FF r2 &= ~M_IO_DATA_MASK
0000BEB1 1A D5 02 70 [P_IO_Data_Di] = r2
0000BEB3 12 95 06 70 r2 = [P_IO_Ctrl_B] //得到IOB口的状态
0000BEB5 0A B5 DB FF r2 &= ~(M_IO_EP+M_IO_CS) //EP CS to Low 20050613 Editby Xinqiang
0000BEB7 1A D5 06 70 [P_IO_Ctrl_B] = r2 //EP Low
0000BEB9 12 95 06 70 r2 = [P_IO_Ctrl_B]
0000BEBB 0A B5 F7 FF r2 &= ~(M_IO_AO)
0000BEBD 50 A4 r2 |= M_IO_RW
0000BEBE 1A D5 06 70 [P_IO_Ctrl_B] = r2 //AO Hight, RW Hight
0000BEC0 00 EE nop
0000BEC1 60 A4 r2 |= M_IO_EP
0000BEC2 1A D5 06 70 [P_IO_Ctrl_B] = r2 //产生EP高电平，
0000BEC4 00 EE nop
0000BEC5 11 93 00 70 r1 = [P_IO_Data]
0000BEC7 09 B3 FF 00 r1 &= M_IO_DATA_MASK
0000BEC9 0A B5 DF FF r2 &= ~M_IO_EP //EP to Low
0000BECB 44 A4 r2 |= M_IO_CS //CS to Hight 20050613 Editby Xinqiang
0000BECC 1A D5 05 70 [P_IO_Ctrl] = r2
0000BECE 12 95 02 70 r2 = [P_IO_Data_Di] //恢复数据口为输出状态
0000BED0 0A A5 FF 00 r2 |= M_IO_DATA_MASK
0000BED2 1A D5 02 70 [P_IO_Data_Di] = r2
.ifdef DATA_PORT_HIGHT
r1 = r1 lsr 4
r1 = r1 lsr 4
.endif
0000BED4 88 92 pop r2 from [sp]
0000BED5 90 9A retf
//****************************************************************************************************
// 128X64I液晶底层驱动[6X8]字体库
// 设计者: powerint
// 描 述: [6X8]西文字符的字模数据 (纵向取模,字节倒序)
// 日 期: 2004.4.27
// 版本号: 1.1
//****************************************************************************************************
.PUBLIC _Asii8
_Asii8:
0000BED6 00 00 00 00 .DW 0x0000,0x0000,0x0000,0x0000,0x065F,0x0600,0x0007,0x0300,0x0703,0x0024,0x7E24,0x7E24
00 00 00 00
5F 06 00 06
07 00 00 03
03 07 24 00
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -