hal_rf_settings.h

msp430 test code and examples for using a 5438

#ifndef HAL_RF_SETTINGS_H_
#define HAL_RF_SETTINGS_H_
/* Chipcon */
/* Product = CC2500 */
/* Chip version = E */
/* Crystal accuracy = 10 ppm */
/* X-tal frequency = 26 MHz */
/* RF output power = 0 dBm */
/* RX filterbandwidth = 541.666667 kHz */
/* Phase = 1 */
/* Datarate = 249.938965 kbps */
/* Modulation = (7) MSK */
/* Manchester enable = (0) Manchester disabled */
/* RF Frequency = 2432.999908 MHz */
/* Channel spacing = 199.951172 kHz */
/* Channel number = 0 */
/* Optimization = Sensitivity */
/* Sync mode = (3) 30/32 sync word bits detected */
/* Format of RX/TX data = (0) Normal mode, use FIFOs for RX and TX */
/* CRC operation = (1) CRC calculation in TX and CRC check in RX enabled */
/* Forward Error Correction = (0) FEC disabled */
/* Length configuration = (1) Variable length packets, packet length configured by the first received byte after sync word. */
/* Packetlength = 255 */
/* Preamble count = (2)  4 bytes */
/* Append status = 1 */
/* Address check = (0) No address check */
/* FIFO autoflush = 0 */
/* Device address = 0 */
/* GDO0 signal selection = ( 6) Asserts when sync word has been sent / received, and de-asserts at the end of the packet */
/* GDO2 signal selection = (11) Serial Clock */
const HAL_RF_CONFIG myRfConfig = {

    0x0B,   // FSCTRL1   Frequency synthesizer control.
    0x00,   // FSCTRL0   Frequency synthesizer control.
    0x5D,   // FREQ2     Frequency control word, high byte.
    0x93,   // FREQ1     Frequency control word, middle byte.
    0xB1,   // FREQ0     Frequency control word, low byte.
    0x86,   // MDMCFG4   Modem configuration.
    0x83,   // MDMCFG3   Modem configuration.
    0x83,   // MDMCFG2   Modem configuration.
    0x22,   // MDMCFG1   Modem configuration.
    0xF8,   // MDMCFG0   Modem configuration.
    0x00,   // CHANNR    Channel number.
    0x44,   // DEVIATN   Modem deviation setting (when FSK modulation is enabled).
    0x56,   // FREND1    Front end RX configuration.
    0x10,   // FREND0    Front end RX configuration.
    0x18,   // MCSM0     Main Radio Control State Machine configuration.
    0x16,   // FOCCFG    Frequency Offset Compensation Configuration.
    0x6C,   // BSCFG     Bit synchronization Configuration.
    0x03,   // AGCCTRL2  AGC control.
    0x40,   // AGCCTRL1  AGC control.
    0x91,   // AGCCTRL0  AGC control.
    0xA9,   // FSCAL3    Frequency synthesizer calibration.
    0x0A,   // FSCAL2    Frequency synthesizer calibration.
    0x00,   // FSCAL1    Frequency synthesizer calibration.
    0x11,   // FSCAL0    Frequency synthesizer calibration.
    0x59,   // FSTEST    Frequency synthesizer calibration.
    0x81,   // TEST2     Various test settings.
    0x35,   // TEST1     Various test settings.
    0x0B,   // TEST0     Various test settings.
    0x0B,   // IOCFG2    GDO2 output pin configuration.
    0x06,   // IOCFG0D   GDO0 output pin configuration. Refer to SmartRF