assemblyinfo.cs

LLBLGen 1.21 Sourcecode

//////////////////////////////////////////////////////////////////////
// Part of LLBLGen sourcecode. See version information
//////////////////////////////////////////////////////////////////////
// COPYRIGHTS:
// Copyright (c)2002 Solutions Design. All rights reserved.
// 
// Released under the following license: (BSD2)
// -------------------------------------------
// Redistribution and use in source and binary forms, with or without modification, 
// are permitted provided that the following conditions are met: 
//
// 1) Redistributions of source code must retain the above copyright notice, this list of 
//    conditions and the following disclaimer. 
// 2) Redistributions in binary form must reproduce the above copyright notice, this list of 
//    conditions and the following disclaimer in the documentation and/or other materials 
//    provided with the distribution. 
// 
// THIS SOFTWARE IS PROVIDED BY SOLUTIONS DESIGN ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, 
// INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 
// PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL SOLUTIONS DESIGN OR CONTRIBUTORS BE LIABLE FOR 
// ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 
// NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR 
// BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 
// STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE 
// USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 
//
// The views and conclusions contained in the software and documentation are those of the authors 
// and should not be interpreted as representing official policies, either expressed or implied, 
// of Solutions Design. 
//
//////////////////////////////////////////////////////////////////////
// Contributers to the code:
//		- Frans Bouma [FB]
//////////////////////////////////////////////////////////////////////
using System.Reflection;
using System.Runtime.CompilerServices;

//
// General Information about an assembly is controlled through the following 
// set of attributes. Change these attribute values to modify the information
// associated with an assembly.
//
[assembly: AssemblyTitle("LLBLGen")]
[assembly: AssemblyDescription("Generator for C# / VB.NET classes and Stored Procedures which will form the Low Level Business Logic Layer")]
[assembly: AssemblyConfiguration("")]
[assembly: AssemblyCompany("Solutions Design")]
[assembly: AssemblyProduct("LLBLGen")]
[assembly: AssemblyCopyright("(c)2002 Solutions Design")]
[assembly: AssemblyTrademark("")]
[assembly: AssemblyCulture("")]		

//
// Version information for an assembly consists of the following four values:
//
//      Major Version
//      Minor Version 
//      Build Number
//      Revision
//
// You can specify all the values or you can default the Revision and Build Numbers 
// by using the '*' as shown below:

[assembly: AssemblyVersion("1.2.*")]

//
// In order to sign your assembly you must specify a key to use. Refer to the 
// Microsoft .NET Framework documentation for more information on assembly signing.
//
// Use the attributes below to control which key is used for signing. 
//
// Notes: 
//   (*) If no key is specified, the assembly is not signed.
//   (*) KeyName refers to a key that has been installed in the Crypto Service
//       Provider (CSP) on your machine. KeyFile refers to a file which contains
//       a key.
//   (*) If the KeyFile and the KeyName values are both specified, the 
//       following processing occurs:
//       (1) If the KeyName can be found in the CSP, that key is used.
//       (2) If the KeyName does not exist and the KeyFile does exist, the key 
//           in the KeyFile is installed into the CSP and used.
//   (*) In order to create a KeyFile, you can use the sn.exe (Strong Name) utility.
//       When specifying the KeyFile, the location of the KeyFile should be
//       relative to the project output directory which is
//       %Project Directory%\obj\<configuration>. For example, if your KeyFile is
//       located in the project directory, you would specify the AssemblyKeyFile 
//       attribute as [assembly: AssemblyKeyFile("..\\..\\mykey.snk")]
//   (*) Delay Signing is an advanced option - see the Microsoft .NET Framework
//       documentation for more information on this.
//
[assembly: AssemblyDelaySign(false)]
[assembly: AssemblyKeyFile("")]
[assembly: AssemblyKeyName("")]