外部中断int0例子.i

请认真阅读您的文件包然后写出其具体请认真阅读您的文件包然后写出其具体

/***************************************************
CodeWizardAVR V1.24.8d Professional
//PD2插上跳线帽/PD3插上跳线帽/PC插上跳线帽,其他的开路
//使用内部时钟
//按动SW按键就可以打开/关闭蜂鸣器
//本例子没有考虑太多的按键防抖动功能
***************************************************/

// CodeVisionAVR C Compiler
// (C) 1998-2004 Pavel Haiduc, HP InfoTech S.R.L.

// I/O registers definitions for the ATmega8


#pragma used+
#pragma used+
sfrb TWBR=0;
sfrb TWSR=1;
sfrb TWAR=2;
sfrb TWDR=3;
sfrb ADCL=4;
sfrb ADCH=5;
sfrw ADCW=4;      // 16 bit access
sfrb ADCSRA=6;
sfrb ADMUX=7;
sfrb ACSR=8;
sfrb UBRRL=9;
sfrb UCSRB=0xa;
sfrb UCSRA=0xb;
sfrb UDR=0xc;
sfrb SPCR=0xd;
sfrb SPSR=0xe;
sfrb SPDR=0xf;
sfrb PIND=0x10;
sfrb DDRD=0x11;
sfrb PORTD=0x12;
sfrb PINC=0x13;
sfrb DDRC=0x14;
sfrb PORTC=0x15;
sfrb PINB=0x16;
sfrb DDRB=0x17;
sfrb PORTB=0x18;
sfrb EECR=0x1c;
sfrb EEDR=0x1d;
sfrb EEARL=0x1e;
sfrb EEARH=0x1f;
sfrw EEAR=0x1e;   // 16 bit access
sfrb UBRRH=0x20;
sfrb UCSRC=0X20;
sfrb WDTCR=0x21;
sfrb ASSR=0x22;
sfrb OCR2=0x23;
sfrb TCNT2=0x24;
sfrb TCCR2=0x25;
sfrb ICR1L=0x26;
sfrb ICR1H=0x27;
sfrw ICR1=0x26;   // 16 bit access
sfrb OCR1BL=0x28;
sfrb OCR1BH=0x29;
sfrw OCR1B=0x28;  // 16 bit access
sfrb OCR1AL=0x2a;
sfrb OCR1AH=0x2b;
sfrw OCR1A=0x2a;  // 16 bit access
sfrb TCNT1L=0x2c;
sfrb TCNT1H=0x2d;
sfrw TCNT1=0x2c;  // 16 bit access
sfrb TCCR1B=0x2e;
sfrb TCCR1A=0x2f;
sfrb SFIOR=0x30;
sfrb OSCCAL=0x31;
sfrb TCNT0=0x32;
sfrb TCCR0=0x33;
sfrb MCUCSR=0x34;
sfrb MCUCR=0x35;
sfrb TWCR=0x36;
sfrb SPMCR=0x37;
sfrb TIFR=0x38;
sfrb TIMSK=0x39;
sfrb GIFR=0x3a;
sfrb GICR=0x3b;
sfrb SPL=0x3d;
sfrb SPH=0x3e;
sfrb SREG=0x3f;
#pragma used-

// Interrupt vectors definitions


// Needed by the power management functions (sleep.h)
#asm
	#ifndef __SLEEP_DEFINED__
	#define __SLEEP_DEFINED__
	.EQU __se_bit=0x80
	.EQU __sm_mask=0x70
	.EQU __sm_powerdown=0x20
	.EQU __sm_powersave=0x30
	.EQU __sm_standby=0x60
	.EQU __sm_ext_standby=0x70
	.EQU __sm_adc_noise_red=0x10
	.SET power_ctrl_reg=mcucr
	#endif
#endasm



interrupt [2] void INT0_isr(void) //INT0的中断向量是2,请参考M48数据手册的48页
{
  PORTD.3=~PORTD.3;               //电平取反
 // EIFR|=1;                        //清除INT0中断触发标记,防止按键抖动
 GIFR|=0x40;
}

void main(void)
{ 
  PORTD.2=1;
  DDRD.2=0;                       //设置INT0端口为输入,上拉电阻有效
  PORTD.3=0;                      
  DDRD.3 =1;                      //设置PD3输出低电平,准备驱动蜂鸣器
  
//  EIMSK|=1;                       //打开INT0中断
//  EICRA|=3;                       //INT0上升沿触发
GICR|=0x40;
MCUCR|=3;
  #asm("sei")                     //插入汇编语句,打开全局中断   
  
  while (1)                       //循环,等待中断 
        {
           #asm("nop")            //空操作的汇编代码,等待中断发生
        };
    }