hw_usb.h

KEIL驱动 各方面各 你的看法女士的烦恼 方看到你

#define USB_RXCSRH1_AUTORQ      0x00000040  // Auto Request.
#define USB_RXCSRH1_ISO         0x00000040  // ISO.
#define USB_RXCSRH1_DMAEN       0x00000020  // DMA Request Enable.
#define USB_RXCSRH1_DISNYET     0x00000010  // Disable NYET
#define USB_RXCSRH1_PIDERR      0x00000010  // PID Error.
#define USB_RXCSRH1_DMAMOD      0x00000008  // DMA Request Mode.
#define USB_RXCSRH1_DTWE        0x00000004  // Data Toggle Write Enable.
#define USB_RXCSRH1_DT          0x00000002  // Data Toggle.
#define USB_RXCSRH1_INCRX       0x00000001  // Incomplete Receive.

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_RXCOUNT1 register.
//
//*****************************************************************************
#define USB_RXCOUNT1_COUNT_M    0x00001FFF  // Receive Packet Count.
#define USB_RXCOUNT1_COUNT_S    0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_TXTYPE1 register.
//
//*****************************************************************************
#define USB_TXTYPE1_SPEED_M     0x000000C0  // Operating Speed.
#define USB_TXTYPE1_SPEED_DFLT  0x00000000  // Default
#define USB_TXTYPE1_SPEED_FULL  0x00000080  // Full
#define USB_TXTYPE1_SPEED_LOW   0x000000C0  // Low
#define USB_TXTYPE1_PROTO_M     0x00000030  // Protocol.
#define USB_TXTYPE1_PROTO_CTRL  0x00000000  // Control
#define USB_TXTYPE1_PROTO_ISOC  0x00000010  // Isochronous
#define USB_TXTYPE1_PROTO_BULK  0x00000020  // Bulk
#define USB_TXTYPE1_PROTO_INT   0x00000030  // Interrupt
#define USB_TXTYPE1_TEP_M       0x0000000F  // Target Endpoint Number.
#define USB_TXTYPE1_TEP_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_TXINTERVAL1
// register.
//
//*****************************************************************************
#define USB_TXINTERVAL1_NAKLMT_M \
                                0x000000FF  // NAK Limit.
#define USB_TXINTERVAL1_TXPOLL_M \
                                0x000000FF  // TX Polling
#define USB_TXINTERVAL1_TXPOLL_S \
                                0
#define USB_TXINTERVAL1_NAKLMT_S \
                                0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_RXTYPE1 register.
//
//*****************************************************************************
#define USB_RXTYPE1_SPEED_M     0x000000C0  // Operating Speed.
#define USB_RXTYPE1_SPEED_DFLT  0x00000000  // Default
#define USB_RXTYPE1_SPEED_FULL  0x00000080  // Full
#define USB_RXTYPE1_SPEED_LOW   0x000000C0  // Low
#define USB_RXTYPE1_PROTO_M     0x00000030  // Protocol.
#define USB_RXTYPE1_PROTO_CTRL  0x00000000  // Control
#define USB_RXTYPE1_PROTO_ISOC  0x00000010  // Isochronous
#define USB_RXTYPE1_PROTO_BULK  0x00000020  // Bulk
#define USB_RXTYPE1_PROTO_INT   0x00000030  // Interrupt
#define USB_RXTYPE1_TEP_M       0x0000000F  // Target Endpoint Number.
#define USB_RXTYPE1_TEP_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_RXINTERVAL1
// register.
//
//*****************************************************************************
#define USB_RXINTERVAL1_TXPOLL_M \
                                0x000000FF  // RX Polling
#define USB_RXINTERVAL1_NAKLMT_M \
                                0x000000FF  // NAK Limit.
#define USB_RXINTERVAL1_TXPOLL_S \
                                0
#define USB_RXINTERVAL1_NAKLMT_S \
                                0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_TXMAXP2 register.
//
//*****************************************************************************
#define USB_TXMAXP2_MULT_M      0x0000F800  // Multiplier.
#define USB_TXMAXP2_MAXLOAD_M   0x000007FF  // Maximum Payload.
#define USB_TXMAXP2_MULT_S      11
#define USB_TXMAXP2_MAXLOAD_S   0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_TXCSRL2 register.
//
//*****************************************************************************
#define USB_TXCSRL2_INCTX       0x00000080  // Incomplete Transmit.
#define USB_TXCSRL2_NAKTO       0x00000080  // NAK Timeout
#define USB_TXCSRL2_CLRDT       0x00000040  // Clear Data Toggle.
#define USB_TXCSRL2_STALLED     0x00000020  // Endpoint Stalled.
#define USB_TXCSRL2_SETUP       0x00000010  // Setup Packet.
#define USB_TXCSRL2_STALL       0x00000010  // Send Stall.
#define USB_TXCSRL2_FLUSH       0x00000008  // Flush FIFO.
#define USB_TXCSRL2_ERROR       0x00000004  // Error.
#define USB_TXCSRL2_UNDRN       0x00000004  // Underrun.
#define USB_TXCSRL2_FIFONE      0x00000002  // FIFO Not Empty.
#define USB_TXCSRL2_TXRDY       0x00000001  // Transmit Packet Ready.

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_TXCSRH2 register.
//
//*****************************************************************************
#define USB_TXCSRH2_AUTOSET     0x00000080  // Auto Set.
#define USB_TXCSRH2_ISO         0x00000040  // ISO.
#define USB_TXCSRH2_MODE        0x00000020  // Mode.
#define USB_TXCSRH2_DMAEN       0x00000010  // DMA Request Enable.
#define USB_TXCSRH2_FDT         0x00000008  // Force Data Toggle.
#define USB_TXCSRH2_DMAMOD      0x00000004  // DMA Request Mode.
#define USB_TXCSRH2_DTWE        0x00000002  // Data Toggle Write Enable.
#define USB_TXCSRH2_DT          0x00000001  // Data Toggle.

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_RXMAXP2 register.
//
//*****************************************************************************
#define USB_RXMAXP2_MULT_M      0x0000F800  // Multiplier.
#define USB_RXMAXP2_MAXLOAD_M   0x000007FF  // Maximum Payload.
#define USB_RXMAXP2_MULT_S      11
#define USB_RXMAXP2_MAXLOAD_S   0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_RXCSRL2 register.
//
//*****************************************************************************
#define USB_RXCSRL2_CLRDT       0x00000080  // Clear Data Toggle.
#define USB_RXCSRL2_STALLED     0x00000040  // Endpoint Stalled.
#define USB_RXCSRL2_REQPKT      0x00000020  // Request Packet.
#define USB_RXCSRL2_STALL       0x00000020  // Send Stall.
#define USB_RXCSRL2_FLUSH       0x00000010  // Flush FIFO.
#define USB_RXCSRL2_DATAERR     0x00000008  // Data Error.
#define USB_RXCSRL2_NAKTO       0x00000008  // NAK Timeout.
#define USB_RXCSRL2_ERROR       0x00000004  // Error.
#define USB_RXCSRL2_OVER        0x00000004  // Overrun.
#define USB_RXCSRL2_FULL        0x00000002  // FIFO Full.
#define USB_RXCSRL2_RXRDY       0x00000001  // Receive Packet Ready.

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_RXCSRH2 register.
//
//*****************************************************************************
#define USB_RXCSRH2_AUTOCL      0x00000080  // Auto Clear.
#define USB_RXCSRH2_AUTORQ      0x00000040  // Auto Request.
#define USB_RXCSRH2_ISO         0x00000040  // ISO.
#define USB_RXCSRH2_DMAEN       0x00000020  // DMA Request Enable.
#define USB_RXCSRH2_DISNYET     0x00000010  // Disable NYET
#define USB_RXCSRH2_PIDERR      0x00000010  // PID Error.
#define USB_RXCSRH2_DMAMOD      0x00000008  // DMA Request Mode.
#define USB_RXCSRH2_DTWE        0x00000004  // Data Toggle Write Enable.
#define USB_RXCSRH2_DT          0x00000002  // Data Toggle.
#define USB_RXCSRH2_INCRX       0x00000001  // Incomplete Receive.

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_RXCOUNT2 register.
//
//*****************************************************************************
#define USB_RXCOUNT2_COUNT_M    0x00001FFF  // Receive Packet Count.
#define USB_RXCOUNT2_COUNT_S    0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_TXTYPE2 register.
//
//*****************************************************************************
#define USB_TXTYPE2_SPEED_M     0x000000C0  // Operating Speed.
#define USB_TXTYPE2_SPEED_DFLT  0x00000000  // Default
#define USB_TXTYPE2_SPEED_FULL  0x00000080  // Full
#define USB_TXTYPE2_SPEED_LOW   0x000000C0  // Low
#define USB_TXTYPE2_PROTO_M     0x00000030  // Protocol.
#define USB_TXTYPE2_PROTO_CTRL  0x00000000  // Control
#define USB_TXTYPE2_PROTO_ISOC  0x00000010  // Isochronous
#define USB_TXTYPE2_PROTO_BULK  0x00000020  // Bulk
#define USB_TXTYPE2_PROTO_INT   0x00000030  // Interrupt
#define USB_TXTYPE2_TEP_M       0x0000000F  // Target Endpoint Number.
#define USB_TXTYPE2_TEP_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_TXINTERVAL2
// register.
//
//*****************************************************************************
#define USB_TXINTERVAL2_TXPOLL_M \
                                0x000000FF  // TX Polling
#define USB_TXINTERVAL2_NAKLMT_M \
                                0x000000FF  // NAK Limit.
#define USB_TXINTERVAL2_NAKLMT_S \
                                0
#define USB_TXINTERVAL2_TXPOLL_S \
                                0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_RXTYPE2 register.
//
//*****************************************************************************
#define USB_RXTYPE2_SPEED_M     0x000000C0  // Operating Speed.
#define USB_RXTYPE2_SPEED_DFLT  0x00000000  // Default
#define USB_RXTYPE2_SPEED_FULL  0x00000080  // Full
#define USB_RXTYPE2_SPEED_LOW   0x000000C0  // Low
#define USB_RXTYPE2_PROTO_M     0x00000030  // Protocol.
#define USB_RXTYPE2_PROTO_CTRL  0x00000000  // Control
#define USB_RXTYPE2_PROTO_ISOC  0x00000010  // Isochronous
#define USB_RXTYPE2_PROTO_BULK  0x00000020  // Bulk
#define USB_RXTYPE2_PROTO_INT   0x00000030  // Interrupt
#define USB_RXTYPE2_TEP_M       0x0000000F  // Target Endpoint Number.
#define USB_RXTYPE2_TEP_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_RXINTERVAL2
// register.
//
//*****************************************************************************
#define USB_RXINTERVAL2_TXPOLL_M \
                                0x000000FF  // RX Polling
#define USB_RXINTERVAL2_NAKLMT_M \
                                0x000000FF  // NAK Limit.
#define USB_RXINTERVAL2_TXPOLL_S \
                                0
#define USB_RXINTERVAL2_NAKLMT_S \
                                0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_TXMAXP3 register.
//
//*****************************************************************************
#define USB_TXMAXP3_MULT_M      0x0000F800  // Multiplier.
#define USB_TXMAXP3_MAXLOAD_M   0x000007FF  // Maximum Payload.
#define USB_TXMAXP3_MULT_S      11
#define USB_TXMAXP3_MAXLOAD_S   0

//*****************************************************************************
//
// The following are defines for the bit fields in the USB_O_TXCSRL3 register.
//
//*****************************************************************************
#define USB_TXCSRL3_INCTX       0x00000080  // Incomplete Transmit.
#define USB_TXCSRL3_NAKTO       0x00000080  // NAK Timeout
#define USB_TXCSRL3_CLRDT       0x00000040  // Clear Data Toggle.
#define USB_TXCSRL3_STALLED     0x00000020  // Endpoint Stalled.
#define USB_TXCSRL3_SETUP       0x00000010  // Setup Packet.
#define USB_TXCSRL3_STALL       0x00000010  // Send Stall.
#define USB_TXCSRL3_FLUSH       0x00000008  // Flush FIFO.